- 更多网络例句与百分表相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Introduced saw chain depth setting and cutting top run-out and cutting top total run-out and side clearance of the cutting edge testing method by the centesimal graduation meter and the instrument microscope, and discussed the testing error.
阐述了利用百分表、万能工具显微镜检测锯链限料量、切削齿齿顶跳动、切削齿齿顶总跳动、侧刃后角的方法，并分析了测量误差。
-
Vernier caliper, digital caliper, depth gauge, combination square set, dial indicator.
3A49 游标卡尺，数显卡尺，深度尺，组合角度尺，百分表。
-
How to do this is: the series-water roll clamping in grinder, head of the bed with a fixed Center, bed end, respectively, with huoluo thimble, despite a string of water both ends of the roll Center always ends up in l, with a dial check and correction of water roll radial runout of excircle and the tiaodong of error control in 0.02mm, to achieve accuracy requirements.
抽象操纵为：把串火辊夹持在磨床上，床头用变动顶针，床尾用方活顶针，分别顶住串火辊两头的边缘孑L，用百分表查抄和订正火辊外方的径向跳动度，并把跳动度的差错把持在0.02mm不以外，使其到达不粗度请求。
-
Traditional method detecting by dial indicator or feeler gauge needs more time and effort.
传统的检测方法是由百分表或触角衡量，需要更多的时间和精力。
-
The method using precise leveling instrument as settlement observation system of static load test in the soft sail is pro-posed herein, for the reasons that conventional combined base beam and dial gauger observation system is easily affected by load platform.
针对软土地区单桩静载试验中常用的基准梁百分表沉降量测系统易受压重平台影响的问题，提出将精密水准仪作为静载试验的沉降量测系统。
-
Company business scope: Metric plug plug plug left teeth straight plug, such as Brandt Gauge Metric ring ring ring teeth left straight Brandt ring ring gauge, such as dedicated short taper gauge cone gauge Mohs gauge needle, such as three types of vernier caliper caliper caliper with standard digital calipers, such as depth micrometer caliper micrometer outside diameter micrometer inside diameter micrometer micron micrometer scale, such as lever-type dial indicator dial indicator inner diameter dial indicator digital display dial indicator, such as Square Block-type wide angle square-foot knife-edge knife-edge angle square feet omnipotent point of view, such as meter-type coordinate measuring machine single lever gear comparator block welding inspection regulations, such as foot and other workers?
本公司经营范围：塞规公制塞规左牙塞规直管塞规布氏塞规等环规公制环规左牙环规直管环规布氏环规等专用量规锥度量规短锥量规莫氏量规三针等卡尺类游标卡尺带标卡尺数显卡尺深度卡尺等千分尺外径千分尺内径千分尺内侧千分尺微米千分尺等量表类百分表杠杆百分表内径百分表数显百分表等角尺类宽座角尺刀口尺刀口角尺万能角度尺等量仪类单坐标测量仪杠杆齿轮比较仪焊接检验尺等块规及其他工？
-
To address this situation, I believe that the operation could be improved on are: the installation and adjustment of measuring, the first sub-scale do to adjust the nominal cylinder liner size, and then dial indicator card installed and well well inserted under the initial installation of the traffic card directly into the cylinder table by measuring the smallest cylinder liner wear, the cylinder table adjust the volume of the extended length of rod inserted, so that the volume of the dial indicator cylinder table has small hands around 1.5-2.0 preloading cell volume and cylinder volume table mother under lock locking plug, the final table and then measured the volume of cylinder rod and rod card inserted at the anvil micrometer measuring bar between the seat and the large dial and adjust the dial indicator to zero.
针对这种情况，笔者认为，操作上可改进为：安装和调整量具时，先将干分尺调整到气缸套的公称尺寸，再将卡装好百分表和初步安装好插杆的量缸表直接卡入所测气缸套磨损最小处，调整量缸表插杆的伸出长度，使量缸表的百分表小表针有1.5-2.0格左右的预压量并将量缸表的插杆锁母锁紧，最后再将量缸表的测杆和插杆卡在千分尺的砧座和测杆之间并将百分表的大表盘调整到零。
-
Engine cylinder liner of the general process of measurement are: cylinder liner according to the nominal size measuring selection, that is, sub-thousand-foot-cylinder form and quantity (including the volume of cylinder rod inserted table); installation and adjustment of measuring, that is first to adjust micrometer cylinder liner the nominal size, and then loaded card good indicator of the volume of cylinder form measuring bar and the bar card inserted in the anvil micrometer measuring bar between the seat and adjust the volume of cylinder form of extended length of rod inserted, when the dial indicator of the 1.5-2.0 cells have small hands around the amount of pre-press under lock-lock female plug, and a large dial indicator to zero adjust
发动机气缸套测量的一般过程是：根据气缸套的公称尺寸选择量具，即千分尺和量缸表；安装和调整量具，即先将千分尺调整到气缸套的公称尺寸，再将卡装好百分表的量缸表的测杆和插杆卡在千分尺的砧座和测杆之间，调整量缸表插杆的伸出长度，当百分表的小表针有1.5-2.0格左右的预压量时锁紧插杆锁母，并将百分表的大表盘调整到零
-
The first direct measurement with micrometer piston skirt and the outside diameter Do micrometer stop screw to the locking plate position, and then dial indicator card installed and well well inserted under the initial installation of the amount of cards, directly into the cylinder corresponding cylinder kit, adjust the volume of the cylinder rod out in table inserted length, so that small hands dial indicator cell has about 1 volume of pre-press and lock locking rod inserted mother, at the same time, large dial indicator dial to adjust zero, the last cylinder to adjust the volume of good form under test card inserted rods and do at Anvil micrometer and measured the rod between the big hands dial indicator at this time than the "zero" high value is the piston and cylinder liner with the space.
3先直接用千分尺测量活塞裙部的外径并将干分尺止动螺钉扳转到锁紧位置，再将卡装好百分表和初步安装好插杆的量缸表直接卡入对应气缸套内，调整量缸表插杆的伸出长度，使百分表的小表针有1格左右的预压量并锁紧插杆锁母，同时将百分表的大表盘调整到零，最后将调整好的量缸表的测杆和插杆卡在干分尺的砧座和测杆之间，此时百分表大表针比&零&高的数值即为活塞和气缸套的配合间隙。
-
The first direct measurement with micrometer diameter piston skirt, and then dial indicator card installed and the initial installation of the amount of good cylinder rod inserted card table micrometer mounted on the anvil between the seat and the measuring bar, adjust the volume of cylinder table Interpolation of the extended length of rod, when the dial indicator has small hands around 1.5-2 cell volume preloading lock locking rod inserted mother, and a large dial indicator to zero adjust the final stretch to the volume of cylinder table into the Cylinder Sleeve, large dial indicator hands than "zero" low value (considering the small hands reading) is the piston and cylinder liner with the space.
2先直接用千分尺测量活塞裙部的外径，然后将卡装好百分表和初步安装好插杆的量缸表卡装在千分尺的砧座和测杆之间，调整量缸表插杆的伸出长度，当百分表的小表针有1.5-2格左右的预压量时锁紧插杆锁母，并将百分表的大表盘调整到零，最后将量缸表伸入气缸套内，百分表大表针比&零&低的数值即为活塞和气缸套的配合间隙。
- 更多网络解释与百分表相关的网络解释 [注：此内容来源于网络，仅供参考]
-
Algol：日本爱固
tutoyo )系列产品:卡尺、千分尺、高度尺、百分表、千分表、角度仪、精密量块、投影机、工具显微镜、表面粗糙度仪、轮廓仪、三坐标测定机、硬度计等、日本(TOHNICHI)东日、0512-55006630中村(KANON)扭力工具、日本爱固( ALGOL)、日本依梦达(IM
-
vernier calliper：游标测径器
vernier calipers with dial indicator 带百分表游标卡尺 | vernier calliper 游标测径器 | vernier callipers 游标卡尺
-
centimeter：百分表
凹槽对接焊缝groove butt joints | 百分表Centimeter | 百分表检定仪Dialgage calibrater
-
cylindrical lens：柱面透镜
柱面透镜(Cylindrical Lens)检测柱面透镜(Cylindrical Lens)检测的检测一直比较薄弱,很多企业对偏心的检测还停留在用百分表或千分表打边厚差.面形测量用样板等水平.本人对这块也不熟悉,希望有这方面检测经验或熟悉的人来给大家介绍介绍!
-
diametric expansion：径向扩张
dial indicator 千分表,百分表 | diametric expansion 径向扩张 | diametrically opposite cylinder 径向对置气缸
-
caliper gages：测径器
17 thickness gages 厚度表 | 18 caliper gages 测径器 | 19 dial test indicators 杠杆百分表/千分表
-
dial gauges：百分表
b5205 金属矩尺 carpenter's squares | b5206 百分表 dial gauges | b5209 金属卷尺 steel tape measures
-
depth dial gauge：深度百分表
内径表 internal dial gauge | 深度百分表 depth dial gauge | 通用卡尺 general gauge
-
test indicator：杠杆百分表
百分表及内径量表 indicator | 杠杆百分表 test indicator | 线性测微计 gage head
-
dial test indicator：千分表, 百分表
dial plate 标度盘, 拨号盘, 指针板, 表盘 | dial test indicator 千分表, 百分表 | part n 部分, 局部, 零件, 角色