dial indicator

dial indicator的基本解释

-

千分表, 刻度盘指示器, 百分表

与dial indicator相关的网络例句 [注：此内容来源于网络，仅供参考]

Company business scope: Metric plug plug plug left teeth straight plug, such as Brandt Gauge Metric ring ring ring teeth left straight Brandt ring ring gauge, such as dedicated short taper gauge cone gauge Mohs gauge needle, such as three types of vernier caliper caliper caliper with standard digital calipers, such as depth micrometer caliper micrometer outside diameter micrometer inside diameter micrometer micron micrometer scale, such as lever-type dial indicator dial indicator inner diameter dial indicator digital display dial indicator, such as Square Block-type wide angle square-foot knife-edge knife-edge angle square feet omnipotent point of view, such as meter-type coordinate measuring machine single lever gear comparator block welding inspection regulations, such as foot and other workers?

本公司经营范围：塞规公制塞规左牙塞规直管塞规布氏塞规等环规公制环规左牙环规直管环规布氏环规等专用量规锥度量规短锥量规莫氏量规三针等卡尺类游标卡尺带标卡尺数显卡尺深度卡尺等千分尺外径千分尺内径千分尺内侧千分尺微米千分尺等量表类百分表杠杆百分表内径百分表数显百分表等角尺类宽座角尺刀口尺刀口角尺万能角度尺等量仪类单坐标测量仪杠杆齿轮比较仪焊接检验尺等块规及其他工？

The first direct measurement with micrometer piston skirt and the outside diameter Do micrometer stop screw to the locking plate position, and then dial indicator card installed and well well inserted under the initial installation of the amount of cards, directly into the cylinder corresponding cylinder kit, adjust the volume of the cylinder rod out in table inserted length, so that small hands dial indicator cell has about 1 volume of pre-press and lock locking rod inserted mother, at the same time, large dial indicator dial to adjust zero, the last cylinder to adjust the volume of good form under test card inserted rods and do at Anvil micrometer and measured the rod between the big hands dial indicator at this time than the "zero" high value is the piston and cylinder liner with the space.

3先直接用千分尺测量活塞裙部的外径并将干分尺止动螺钉扳转到锁紧位置，再将卡装好百分表和初步安装好插杆的量缸表直接卡入对应气缸套内，调整量缸表插杆的伸出长度，使百分表的小表针有1格左右的预压量并锁紧插杆锁母，同时将百分表的大表盘调整到零，最后将调整好的量缸表的测杆和插杆卡在干分尺的砧座和测杆之间，此时百分表大表针比&零&高的数值即为活塞和气缸套的配合间隙。

The first direct measurement with micrometer diameter piston skirt, and then dial indicator card installed and the initial installation of the amount of good cylinder rod inserted card table micrometer mounted on the anvil between the seat and the measuring bar, adjust the volume of cylinder table Interpolation of the extended length of rod, when the dial indicator has small hands around 1.5-2 cell volume preloading lock locking rod inserted mother, and a large dial indicator to zero adjust the final stretch to the volume of cylinder table into the Cylinder Sleeve, large dial indicator hands than "zero" low value (considering the small hands reading) is the piston and cylinder liner with the space.

2先直接用千分尺测量活塞裙部的外径，然后将卡装好百分表和初步安装好插杆的量缸表卡装在千分尺的砧座和测杆之间，调整量缸表插杆的伸出长度，当百分表的小表针有1.5-2格左右的预压量时锁紧插杆锁母，并将百分表的大表盘调整到零，最后将量缸表伸入气缸套内，百分表大表针比&零&低的数值即为活塞和气缸套的配合间隙。

与dial indicator相关的网络解释 [注：此内容来源于网络，仅供参考]

dial indicator：针盘指示表

调整斜度,以调整底座之高度及水平度.之距离以测微器(Micro-meter)测定之而调整到0.01mm以下之精度.由负荷机械之联结器面至如第5图所示,於电动机侧之联结器上装上针盘指示表(Dial indicator)将电动机转部静静地其次,

dial indicator：刻度盘指示器

dial gauge 刻度盘 | dial indicator 刻度盘指示器 | dial instrument 度盘式仪表

dial indicator：千分表

dial indicator 拨号盘速度指示器千分表 | dial indicator 千分表 | dial lamp 标度灯