trigger mode

trigger mode的基本解释

-

触发模

与trigger mode相关的网络例句 [注：此内容来源于网络，仅供参考]

Study 2 used 2(conflict target: supervisor/subordinate)×3(conflict management mode: integrating/obliging/dominating ) design, letting participants to evaluate the effeciency and appropriateness of the management mode used in the contexts. The results showed:(1) the integrating mode were perceived most efficient and appropriage within the three conflict modes;(2) the interaction between the referent role of conflict object and the management mode is significant, which means when the conflict took place with the supervisor, the participants thought the obliging mode was more appropriate and efficient , while when it took place between the subordinate, they thought the dominating mode was more appropriate and efficient than obliging mode.(3)the interaction between SDO and conflict management mode is significant, which means the participants with high SDO would make no preference between obliging and dominating mode, but the participates with low SDO would favor the dominating rather than obliging mode;(4) the interaction between dialectical ways of thinking and conflict management mode is significant, the lower the level of dialectical way of thinking the participants were, the more difference were found between the appraisal of obliging and dominating mode.(5) the moderating effect of SDO and dialectical ways of thinking to the relationship between conflict object and management mode were not significant, which means the relative position of conflict object in China is so strong that can't be affected by SDO and dialectical ways of thinking.

研究二采用2*3（冲突处理方式：迁就/支配/整合）的情境设计，让被试对情境中冲突主角的冲突处理方式进行恰当有效性的评价，结果显示： 1、在与上级或下级发生冲突时，被试对迁就、支配和整合三种策略中整合式的恰当有效性的评价最高；2、冲突对象的相对地位与冲突处理方式之间的交互作用显著，即当与上级发生冲突时，被试认为使用迁就的处理方式比支配的方式更恰当有效，而与下级发生冲突时，被试则认为使用支配的处理方式比迁就的方式更有效； 3、SDO与冲突处理方式之间的交互作用显著，即SDO水平高的被试对迁就式与支配式的认知评价没有差异，而SDO水平低的被试对支配式比迁就式有更高的评价；4、辩证思维水平与冲突处理方式之间的交互作用显著，即低辩证思维水平的个体比高辩证的个体对支配式与迁就式的评价差异更大；5、SDO水平及辩证思维方式水平对冲突对象影响冲突处理方式评价的程度的调节作用不显著。

A hammer drill, in particular a chipper comprising: a body 2 having at least one support handle 4; an electric motor mounted within the body 2 ;an electric switch 22, capable of being switched on and off by a trigger button 8 connected to it, to activate or deactivate respectively the electric motor, wherein the trigger button 8 is moveable between two positions, a first position where the electric switch 22 is off and a second position where the electric switch 22 is on; a locking arm 38 moveably mounted on the electric switch 22 which, when the trigger button 8 is located in its second position, is moveable between two positions, a first position where it is disengaged from the trigger button 8 and a second position where it engages with the trigger button 8 and holds the trigger button 8 in its second position.

锤钻特别是錾，包括：本体(2)，该本体(2)具有至少一个支撑手柄(4)；安装在本体(2)内的电动马达；电开关(22)，该电开关(22)能够由连接到电开关(22)上的触发按钮(8)接通和断开，从而分别使电动马达启动或停用，其中该触发按钮(8)能够在两个位置即第一位置和第二位置之间移动，在该第一位置处电开关(22)断开，在该第二位置处电开关(22)接通；可移动地安装在电开关(22)上的锁紧臂(38)，当触发按钮(8)位于它的第二位置中时，该锁紧臂(38)能够在两个位置即第一位置和第二位置之间移动，在该第一位置处锁紧臂(38)与触发按钮(8)脱离，在该第二位置处锁紧臂(38)与触发按钮(8)接合并将触发按钮(8)保持在触发按钮(8)的第二位置中。

Trigger control circuit in accordance with pulse phase and input along the angle of the trigger value, the corresponding time delay after the rising edge of trigger pulse, open SCR, and in the corresponding half-cycle before the end of hair falling edge trigger pulse, turn-off thyristor, for the next half cycle of the trigger ready.

触发控制电路根据鉴相脉冲沿和输入的触发角数值，延迟相应时间后发出触发脉冲上升沿，打开可控硅，并在相应半个周期结束前发触发脉冲下降沿，关断可控硅，为下个半周期触发做好准备。

与trigger mode相关的网络解释 [注：此内容来源于网络，仅供参考]

external trigger input：外触发输入

external trigger 外触发器 | external trigger input 外触发输入 | external trigger pulse 外触发脉冲

trigger input circuit：触发输入电路

trigger input 触发脉冲输入 | trigger input circuit 触发输入电路 | trigger inverter 触发脉冲变换器

Trigger guard：护弓

Trigger 扳机 | Trigger guard 护弓 | Trigger pull 扳机压力