输出电流

The principle of constant power drive is: PD converts the change of output light power of laser diode into the change of diode current, and the change of current is feed back to voltage-current converser which adjusts output current of driver to compensate the laser diode.

这样，当激光器的输出光功率衰减时，驱动器相应的增大输出电流；当激光器的输出光功率增强时，驱动器就相应减小输出电流。对许多激光器应用来说，最希望脉冲输出，因为脉冲输出只有极小的结发热。

The structure of the design include a nucleus manipulator (AT89S52 ), the current , sampling, comparision amplification, A/D, D/A converter, keyboard display, and so on .

本设计是基于单片机的一种数控电源，与一般电源相比具有宽范围电流输出、可修改性所需电流键盘输入、两级步进调节、输出电流及设定电流显示、负载两端电压显示、纹波系数小等特点。

34C02M8/LM8 Pinout: Short Circuit Current Output Current Transition Time Maximum Transmission Rate 1,000 RS-422 RECEIVER Common Mode Range Differential Input Differential Input Threshold-0.2 Input Voltage Hysteresis30 Input Resistance3 TTL Output Level V V2.4 Maximum Receiving Rate1,000 Short Circuit Output Current POWER REQUIREMENTS V =+12V, 10% V =+5V, 10% V =-12V, 10% ENVIRONMENTAL Operating Temperature -CS0 -MR-55 Storage Temperature-65

34C02M8/LM8引脚说明：短路电流输出电流过渡时期的最大传输速率1000的RS - 422接收器差分输入共模范围差分输入阈值0.2输入电压Hysteresis30输入Resistance3 TTL输出等级V 2.4版本的最大接收Rate1，000短路输出电流电源要求ν= 12五，10％的V =+5 V的，10％的V =- 12V的，10％，环境工作温度- CS0 -议员- 55存储温度- 65

This kind of system utilizes a new current-sharing scheme which amazingly bases on magnetic amplifier and average current-sharing method.The whole design of the modulized electroplating power system is discussed. The power section of the system is made up of a few power modules, and the control section is a simple and common PWM controller with compensation network.

随着开关电源输出电流的日益增加，由多个电源模块并联替代单个大电流模块输出大电流的优势也越来越明显，灵活而且经济的分布式电源系统已经成为电镀电源系统之趋势，而其中的电源模块电流平衡成为技术关键之一。

Because the primary source of noise in an amplifying IC is its input stage, you can assume that the standard deviation of the random component of output current of the paralleled-N voltage-to-current converters is σNI=σI×, where σI is the standard deviation of the random component of output current of a voltage-to-current converter.

由于放大器噪声的主要来源为输入端，假设N个并联电压电流转换器输出电流的随机器件标准差为σNI=σI×，σI为电压电流转换器输出电流的随机器件标准差。

And a signal processing interface board is done to acquire these parameters such as engine speed, excitation current, output current, output voltage, and battery current.

和一个信号处理接口板是为取得这些参数，如发动机转速，励磁电流，输出电流，输出电压，电池和电流。

A zero rippled input current and continuous output current Buck-Boost converter topology converter was proposed.

针对传统Buck-Boost输入输出电流断续的缺点，提出一种基于独立电感零纹波输入电流和输出电流连续的Buck-Boost变换器，详细分析了变换器的稳态工作原理。

Record data include generator voltage UG1,UG2, auto setting value UGREF,manual setting value IFREF, trigger angle ARF, active power P, reactive power Q, rotor voltage Ufd, field current Ifd, generator frequency F0, local cabinet output current ILA, other cabinet output current ILB.

记录的数据包括发电机电压UG1，UG2，自动给定值UGREF，手动给定值IFREF，触发角 ARF，有功功率P，无功功率Q，转子电压Ufd，励磁电流 Ifd，发电机频率F0，本柜输出电流ILA，它柜输出电流ILB。

A tested prime motor is mechanically connected with a magnetic particle brake through driving steps, an instruction computer controls the output current of a power program controller, and the output current is used as the excitation current of the magnetic particle brake. A ball feed screw is arranged between a decelerator and a counterweight pan during the driving steps, and a cap nut covers on the ball feed screw. The holder of the ball feed screw is fixedly provided with a guide rail which is fixedly connected with the cap nut through a flange.

其被测试原动机通过传动环节与磁粉制动器机械连接，指令计算机控制电源程序控制器的输出电流，电源程序控制器的输出电流作为磁粉制动器的激磁电流，传动环节中在减速器和配重盘之间设有一滚珠丝杠，滚珠丝杠上套设一螺母，在滚珠丝杠的底座上固定一导轨，该导轨与螺母通过法兰固定连接。

Operational Tran conductance lifers and Grounded actorhas become one of the most important methods to implement integrated continuous-time filters. Operational Tran conductance Amplifierscan transfer input voltage into current to output,and control or change output current within large range by an external controlling current of amplifier. Most articles consider OTA as a voltage-mode circuit component and give voltage-to-voltage transfer function of all having been implemented filter circuits,i.e. The input signal and output signal of filter circuits are voltages .

运算跨导集成运算放大器OTA ( Operational Tran conductance Amplifier 以下简称跨导运放)的功能是将输入电压转换为电流输出，并通过外加偏置电流控制运放的工作电流，从而使它的输出电流在较大范围内变化，而在大多数文献中，器件都被作为电压模式元器件使用实现的各种滤波电路都是按传送电压比给出的，即滤波电路输入信号和输出信号均为电压信号。

What are your goals and strategies for growth?

你的成长目标和策略是什么？

And unto the angel of the church in Sardis write; These things saith he that hath the seven irits of God, and the seven star I know thy works, that thou hast a name that thou livest, and art dead.

3：1 你要写信给撒狄教会的使者，说，那有神的七灵和七星的，说，我知道你的行为，按名你是活的，其实是死的。