轴的

The method is :there are two perpendicular axes whose distance are controlled ,one is the axis of work table, the other is fixed with a microscope for aiming.

该测量方法是：两个相互垂直且间距可调的数控回转轴，一轴与工件的回转中心重合，另一轴上固定可移动的瞄准显微镜，当显微镜瞄准被测孔时，两轴的转角由各自的圆光栅测出，两轴之间的角度位置确定曲面壳体零件上小孔的孔位置，同时采用CCD摄像头，利用图象处理技术实现小孔的尺寸测量。

A cap and two pinch bolts hold the crank in place, rather like a threadless headset.

与大飞联体的中轴，在安装时有些像在装无纹前叉：在轴的另一端，曲柄像立把一样，用两颗螺丝把中轴夹紧。

Two shaft-less roll mounting positions are provided on a rotating turret which positions the full rolls conveniently for unloading and remounting of an empty spindle while the working roll is winding the product.

两个少轴的轴辊的挂载位置是在旋转塔上面，而旋转塔的位置可以方便地将轴辊卸下或在工作中的轴辊吹送产品的同时重新挂载一个空的主轴。

A miniature motor 1 includes: a motor case 2; a gear case 5 connected to the motor case 2, for pivotally supporting an output shaft 15; a brush holder 30, 30 ' for holding a brush 17 and attached to the gear case 5; and a brush holder attaching portion 7, 7 ', which is formed into a recess-shape, into which the brush holder is press-fitted in the axial direction of the output shaft, the brush holder attaching portion being formed integrally with the gear case.

本发明公开了一种微型马达(1)，包括：马达壳体(2)；连接到马达壳体(2)上的齿轮箱(5)，用于可枢转地支撑输出轴(15)；电刷托架(30、30′)，用于保持电刷(17)并安装到齿轮箱(5)上；以及电刷托架安装部分(7、7′)，该安装部分形成为凹陷形状，电刷托架沿着输出轴的轴向压配合到该安装部分内，电刷托架安装部分与齿轮箱一体地形成。

According to the structural feature of modern tilting levels, the method of erecting the collimation axis to the standing axis and the principle of the setting out of slope with the tilting standing axis are expounded.

根据现代微倾水准仪的视准轴可以调整的构造特点，阐述了使水准仪视准轴垂直于竖轴的方法，以及倾斜竖轴法放样斜坡面的原理；讨论了其误差来源、大小；对照几个行业的设计、施工及验收规范和测量规范，给出了简便可行的操作方法与有效检验手段。

The introductive robot arm of this text can output two lines pulses by the PLC, driving the horizontal stalk, and the perpendicular stalk to drive the electrical engineering actuator respectively, to control the robot arm precision of the horizontal stalk and perpendicular stalk at the fixed position, tiny move switch input the position signal to the PLC.The direct current motor drags along to begin the claw and bedrocks to revolve, the position signal from revolve the code dish and near to the switch feedback to host of PLC;The electromagnetism valve control the machine hand open and close, thus carry out the function of the machine hand precision work.

本文介绍的机械手是由PLC输出两路脉冲，分别驱动横轴、竖轴步进电机驱动器，控制机械手横轴和竖轴的精确定位，微动开关将位置信号传给PLC主机；直流电机拖动手爪和底盘旋转，位置信号由旋转码盘和接近开关反馈给PLC主机；电磁阀控制气开阀的开关来控制机械手手爪的张合，从而实现机械手精确运动的功能。

The rolling wheel of D51 rolling loop machine is fixed with an expansion ring and its axial locating accuracy is high so the processing difficult of rolling wheel is reduced.

D51型辗环机辗压轮系采用涨圈固定，轴向定位精度高，简化了辗压轮的机械加工；下支承轴端圆锥孔后面设有方孔，辗压辊与下支承轴的联接可靠，更换容易，减少了非生产性工作消耗，提高了劳动生产率。

According to the power transmission shaft and the drive shaft speed design and analysis of the axial force, a strength of the shaft Verification, and select bearings and bearing strength calculation.

根据轴传递的功率及转速设计出各传动轴，并分析轴的受力情况，对轴进行强度校核，并选择轴承和轴承强度计算。

The fatigue analysis also was carried out with FE-SAFEWORKS then the fatigue life was predicted. A new way of design of coupling shaft is proposed.

基于此，应用有限元方法分析了转接轴静强度，并用FE-SAFEWORKS模块对转接轴进行疲劳分析，计算其寿命，从而为转接轴的设计提供一种新的思路。

Because the traditional design of the pump shaft and its strength calibration are quite tedious, it is extremely necessary and imminent to develop a set of convenience and dependable CAD software to improve the quality and efficiency of shaft part in the pump and to achieve the combination of the pump shaft intensity calibration and AutoCAD.

鉴于泵轴传统手工设计和强度校核的繁琐，开发一套方便、可靠的适用于水泵轴类零件强度校核的CAD系统以提高泵轴类零件设计的质量与效率，实现轴的强度校核计算与AutoCAD技术的结合就显得非常迫切和必要。

If you are unfortunate enough to the lovelorn, please tell me, I will help you out, really, please contact me!

如果你不幸失恋了，请告诉我，我会帮助你摆脱困境，真的，请联系我啦！

China's plan to cut energy intensity by 20 percent and pollutant discharges by 10 percent between 2006 and 2010 is a case in point.

中国计划在2006年到2010间降低20%的能源强度和减少10%的主要污染物排放，就是一个这样的例子。