转向轴

The trailer designed to not only meet the biaxial workplace narrow the request of the carriers, but also economical and practical.

本次设计的双轴转向拖车不但满足工作场地狭窄的运输工具的要求，而且经济实用。

Rotation: counter clockwise facing motor shaft coupling.

转向：面对电机轴为逆时针。

This paper uses the ADAMS software to set up a dynamic model of tractor-trailer combination consisting of one tractor and five trailers with a total of 13DOF. The effects of drawbar length, articulation joint position on path following performance are investigated using parameter analysis method.

本文应用机械系统分析软件ADAMS建立了由一节牵引车和五节双轴转向拖车组成的汽车列车系统13个自由度的动力学模型，采用模型参数化分析方法，讨论了牵引杆长度、主车与拖车和拖车与拖车的铰接点位置对主车与拖车轨迹同辙性的影响。

The axial and bending characteristis models the of the pneumatic pressure artificial muscle actuator were set up according to the energy conservation law and the infinitesimal deformation theory respectively, and simulation researches and experiments had been done for the characteristics of the actuator.

论文基于能量守恒与转换定律及最小形变原理建立了空气压人工筋驱动器的轴向驱动力学模型及弯曲转向特性模型，仿真计算了人工筋驱动器的驱动力学特性及弯曲转响特性，通过实验研究对理论模型进行了实验验证。

Mainly produce touch upon mini cars, light trucks, and motorcars, with over 300 product types of knuckle, semi-axis, gear, flange pipe, bearing, gasoline engine crankshaft, etc.. To supply specialty service and high quality products to domestic producers, such as Changan Group, Cherry Group, JMC, JAC, SGMW, Jianan Cheqiao Corp., CSG TRW Chassis Systems Co., Ltd. etc..

主要产品包括微型车、轻型车、轿车的转向节、半轴、齿轮、联结盘、轴颈、轴承座、通用汽油机曲轴以及拖拉机轮轴等300多种产品，分别为长安、上汽五菱、上汽奇瑞、江铃、江淮、柳州五菱汽车工业有限公司、南方汽车股份公司四川建安车桥公司、南方天合等主机厂及零部件公司配套。

Test tasks: to check whether the loose connector; hand plate coupling the rotor to move a few laps to see whether rotation and flexible unit, whether there is uneven sound and light and heavy feeling, to determine whether pump or foreign body axis is curved seals, such as the installation is correct; inspection seal on the 20th cavity clean lubricants are added 1 / 2 cavity space; pump unit surface is clean; unit no-load test shift.

试车工作：检查连接件是否松动；用手盘动联轴器使转子转数圈，看机组转动是否灵活，是否有响声和轻重不匀的感觉，以判断泵内有否异物或轴是否弯曲，密封件安装正不正等；检查密封腔内的清洁20号润滑油是否加注1/2腔内空间；泵机组表面是否干净；机组转向空载测试。

Test job: to check whether the connections loose; hand plate coupling the rotor to move a few laps, watch crew rotation is flexible, it has the sound and feeling of the severity of Unevenness to determine whether there is foreign body pump or shaft is bending, sealing the installation is not correct, etc.; inspection seal cavity clean lubricants on the 20th whether or not add 1 / 2 cavity space; pump unit surface is clean; crew turned no-load test.

试车工作：检查连接件是否松动；用手盘动联轴器使转子转数圈，看机组转动是否灵活，是否有响声和轻重不匀的感觉，以判断泵内有否异物或轴是否弯曲，密封件安装正不正等；检查密封腔内的清洁20号润滑油是否加注1/2腔内空间；泵机组表面是否干净；机组转向空载测试。

Steering axis inclination is the inward tilt of the steering knuckle at the top.

指点轴倾向指点轴倾向是转向关节的内部掀动在上面。

The yaw velocity gains of the vehicle and the relationship among the steering center position,the 2th and 3rd axle steering angle ratio and vehicle's speed are analyzed based on the zero side-slip proportional control strategy of mass center.

引言近年来，由于市场需求及高等级路面里程的增加，公路载货车及其他特种车辆的车身及其吨位越来越大，其车轴数目也相应增加，这样造成其转向以及在复杂弯道上的通过性都较小型车要困难得多，因此多轴车特别是大型多轴车向多轮转向方向发展。

HanDe leading products include Hub Reduction Drive Axle, Single Reduction Driving Axle, Steering Axle and Tag Axle etc. totaling 5 series of more than 50 types' products.

公司主导产品有：轮边减速驱动桥、单级减速驱动桥、转向前轴、重型军用越野车驱动桥、挂车承载轴等五大类50多个品种。

I am sure after a few weeks of adaptation and familiarization I will have no difficulty in functioning on a daily basis in an English speaking society or in participating fully in graduate studies.

在大学的三年的学习生活不仅给予我自身的充实，更重要的是磨练和培养了我较强的自觉能力和严谨，踏实的作风以及不怕困难的精神，对未来充满了信心！

As the first volcanoes erupted, one of the gases that bellowed out was steam.

在第一批火山喷发时，喷出的气体之一就是水蒸汽。