焊接

The welding of sleeve and steel plate, anchor bar and sleeve all adopt the intermittent welding.

套筒与钢板的焊接，锚筋与套筒的焊接均采用间断焊接。

It is shown that the simulation results of welding current, arc length and wire extension agree with the experimental results in fillet joints.

实际焊接试验显示，模拟焊接电流与实际焊接电流波形高度吻合，说明建立的数学模型是准确的。

It is successful to re melt deposit pure copper rotating band with D 30 shell body by using the process.

研究了一种新的焊接工艺方法——熔敷焊接方法，采用该方法在 3 0 mm口径弹体上焊接纯铜弹带取得成功。

It is successful to re-melt deposit pure copper rotating band on D-30 shell body by using the process.

本研究探索了一种新的焊接工艺方法—熔敷扩散焊接方法，采用该方法在 30口径弹体上焊接纯铜弹带取得成功。

The application of welded reinforcing bar net in bridge construction is introduced. The bridge top build with it has advantages: simple paving design, constructing conveniently, high efficiency, quality guaranteed.

介绍了钢筋焊接网在桥梁建设中的应用，钢筋焊接网桥面具有铺装设计简单、场施工方便、效，施工质量有可靠保证的优点，大量的工程实践表明钢筋焊接网的应用具有广阔的发展空间。

The welding conditions can be conformed by the stress situation,6 different parameters were used for all position welding. The activating fluxes were deposed on the metal surface by a brusher.

在分析涂敷活性剂时熔池受力变化的基础上制定了焊接规范，管道全位置焊接时分6段进行参数设置，每一段采用不同的焊接参数。

By application in one large ethylene engineering,it was demonstrated that the welding procedure of chrome molybdenum alloy steel was right and rational,at a greater degree,it improved the welding quality and decreased defects in the welding process.

通过在某大型乙烯工程施工中的实际应用，验证了此铬钼合金钢焊接工艺是正确合理的，能够较大程度提高管道焊接质量，减少焊接时各种缺陷的产生。

According to the results of comparison between these methods of spectrum evaluation, a new method of power spectrum evaluation of welding arc sound is advanced by means of association of wavelet packet analysis with the Welch average method .

对试验系统采集到的焊接电弧声进行了小波包多层分解，并利用周期图法、Welch 平均法及AR模型法，对各频段信号进行功率谱估计。根据不同谱估计方法的对比结果，提出小波包分解结合Welch 平均法对焊接电弧声进行功率谱估计的新方法。通过对几种规范与飞溅率下的电弧声功率谱的初步分析，发现其功率谱分布具有一定的规律性，并且不同频段谱峰值及其对应频率与焊接飞溅具有相关

Most of the component structure connected by welding. Ensure welding intensity while minimizing the distortion of welding.

整个机构的大多数联接方式是焊接，应保证焊接强度，同时尽量减少焊接的变形量。

This broad weld will improve the strength of the constantan/ copper junction and provide a large area pad for welding to third party base materials.

这种大面积的焊接会增加康铜与铜接合的强度，从而提供一个大范围的焊接点来与第三方基体材料焊接。

On closer examination, though, this is not a vote for multilateralism but just the opposite.

仔细审视后我们发现，这并非是对多边主义投出的赞成票，而是恰好相反。

Uncovering their weak spots, so I can defeat them.

揭露出他们的弱点，这样我就可以打败他们了。