槽的

Two sets of optimized sizes under two sets of different weighting coefficients were given, and the corresponding width of channel were 130 and 120 μm, and fin width were 176 and 350 μm, and height were 640 and 1000 μm, and the thermal resistance were 0.4857 and 0.5094 K/W, respectively.

给出了2种加权系数情况下的优化尺寸，相应的微槽宽度分别为130 μm和120 μm，槽栅的宽度分别为176 μm和350 μm，微槽的高度分别为640 μm和1000 μm，相应的热阻分别为

Another cover is not closed tightly.

另一处弱电线槽的槽盖也未盖严实。

In this paper,a cutting method of machining straight slot-parts is mainly researched by using the principle of cycloid .

本文主要研究利用摆线原理加工直槽的方法，从理论方面证明利用摆线原理加工直槽的可行性，并且基于VER ICUT仿真平台实现了直槽类零件的连续切削的动态加工仿真

Unslotted magazines are processed in a downstream configuration, slotted magazines are more properly placed on a rotating platform.

处理未开槽的盒子放于槽中的下部，有槽的适合放于旋转的平台。

Any motherboard chipset of DIMM memory slots of the maximum output power is limited, this is the same time, we double-sided multi-use memory and stuck all the memory slots, and a total capacity of memory did not reach the motherboard chipset supported by the upper limit of memory, the computer does not recognize a total capacity of memory, and even can not open one of the major reasons.

任何主板芯片组都对DIMM内存插槽(或是其他形式的内存插槽)的最大输出功率有限制，这也就是我们同时使用多根双面内存将所有内存插槽插满，而内存总容量并没有达到主板芯片组所支持的内存上限时，计算机无法识别内存总容量，甚至是无法开启的一个重要原因。

Aquatic plants were soaked in two purifying-tanks to investigate the effects of illumination intensity and aeration on diurnal variations of Chla,SP,POD of Pontederia cordata and pH,DO,COD,NH+4-N,TP of water from purifying-tanks when treating the malodorous river water at seven different times,another blank purifying-tank was set as a control. Comparative studies and correlation analysis of these different indicators were carried out to improve the plants working efficiency and provide scientific basis for optimal operation of plant purifying-tanks.

测定了曝气和非曝气的2个植物净化槽在1 d中7个不同时间点的出水水质理化指标(pH、DO、COD、NH+4-N、TP)及植物叶片的叶绿素、可溶性蛋白含量及过氧化物酶活性，另设空白槽为对照；试验目的是研究各指标的日变化情况及相互关系，为提高梭鱼草净化黑臭河水的处理效率及其植物净化槽的合理优化运行提供科学依据。

The analysis of leakage causes for flash trough was presented, and the wear layers on inlet tube and the baffle wear plate inside of flash trough were used to increase the wear life of flash trough.

分析了闪蒸槽泄漏的原因，采用在进口接管堆焊耐磨层及筒体上增加耐磨档板的方法对闪蒸槽进行了改造，增加了闪蒸槽的寿命。

In the paper, the vacuum infusion molding process based on grooves was investigated by experiments, and the parameters of width, d e pth and spacing for flow grooves and spacing for supply grooves were optimized a ccording on the molding experiments and various factors that had influence on th e mold filling process were discussed.

真空注射成型工艺是一种新型的复合材料液体模塑成型工艺，对沟槽型真空注射成型工艺开展了实验研究，通过充模实验确定了引流槽的宽度、深度和槽间距及主槽的槽间距等工艺参数并进行了优化；对影响充模过程的各种因素进行了详细的讨论，并以夹芯面板的制作实例阐述了沟槽型真空注射成型的工艺过程。

The utility model profiles is cross-section shaped that in the side,there is the lumen cross-section.vertical profiles of inter-connected connectors connects eucampia square plate-shaped nut screw connected to the bottom profile and the slot between the rectangular cross-section of the convex edge grip tightly, so to connect high strength, easy disassembly

本实用新型的型材是在侧面上有内腔横截面是工字型槽的型材，垂直连接的型材间有弯角连接件和方板形螺母用螺钉相连，可把型材槽底和槽口间的矩形截面的凸棱紧紧夹住，所以连接强度高，拆装方便

The profile of the utility model is a cavity in the side. there is a cross-section of the trough-shaped profile, the vertical connection between section corner and the square plate connector with screw-shaped nut attached to the bottom profile and the slot between the rectangular cross-section of the convex edge grip tightly, so to connect high strength, easy to disassembly

本实用新型的型材是在侧面上有内腔横截面是工字型槽的型材，垂直连接的型材间有弯角连接件和方板形螺母用螺钉相连，可把型材槽底和槽口间的矩形截面的凸棱紧紧夹住，所以连接强度高，拆装方便

If you are unfortunate enough to the lovelorn, please tell me, I will help you out, really, please contact me!

如果你不幸失恋了，请告诉我，我会帮助你摆脱困境，真的，请联系我啦！

China's plan to cut energy intensity by 20 percent and pollutant discharges by 10 percent between 2006 and 2010 is a case in point.

中国计划在2006年到2010间降低20%的能源强度和减少10%的主要污染物排放，就是一个这样的例子。