斜度

The second row of blocks should be cut beveled at thebottom so the layer begins to slant inward toward the middle.

第二层的雪砖底部要切割的有一个斜度，这样垒起来就向中间收口了。

On the basis of previously research, this paper re-probe into the mechanism of electro-chemist mechanical manufacturing process, making the rational technological parameter, and developing the manufacturing equipment. Through a lot of technology tests, get a lot of labratory data, accordingly, researched the surface feature of the electro-chemist manufacturing process, and deeply discussed its influence on the work piece feature. The last result is that: the electro-chemist mechanical manufacturing process can reduce the low-frequency component significantly, but on high-frequency component, it has little influence, having obviously positive pole flat effect. After manufacture, the tip parts on the surface of the work piece is cut off, there is micro "high land" shape, the parameter for surface roughness is reduced a lot, the surface outline of the work piece is negative, the bearing length rate is cliffy. Also the surface quality of the work piece is improved. This can help to avoid changing the shape, improve the feature of rub, gear and reduce the time to suit. This would also ensure the precision and result in a longer work piece life.

在以前研究的基础上，本论文重新探讨了电化学机械复合光整加工工艺的机理，确定了较合理的工艺参数，对电化学机械复合光整加工设备进行了改进，通过工艺实验广泛地搜集了大量实验数据，依据实验数据，多角度地研究了电化学机械复合光整加工的表面形貌特点，并且从理论上深入讨论了电化学机械复合光整加工表面形貌对工件工作性能的影响，最后得出的结论为：电化学机械复合光整加工对工件原始表面的低频成分有较大程度的降低，而对高频成分影响较小，有明显的阳极整平作用，被加工工件表面的尖峰状凸起被去除，工件表面呈现出微观&高原型&，表面轮廓不平度高度特性参数大幅度降低，工件表面轮廓分布集中，且呈负偏态，轮廓偏斜度为负值，轮廓支承长度率曲线陡峭，工件的表面质量得到综合改善，这对提高零件的抗接触变形能力、改善摩擦、磨损性能、降低工件的磨合时间、提高工件的精度保持性、延长工件的寿命均有利。

A further advantage is the smaller pitch of the screws allowing more threads to grasp the thinner cortices.

另一项优势是螺钉较小的斜度让更多的螺纹把持薄的皮质骨。

Diameter precision grinding; Machinable professional and technical personnel of high precision internal diameter, inside diameter and control the depth gradient.

精密内径研磨；专业的技术人员可加工精度较高的内径、斜度与控制内径深度。

Other clues that Tom would look for included the toeing marks, sideward ridges on the tracks, the length of the stride, and the size of the track.

其他汤姆还会找寻的线索包括：行走时趾尖方向的痕迹、足迹侧面脊的斜度、步幅的长度、和足迹的大小。

Finally a computer routine based on SLDMINV has an ability of simulating the measurement of induction sonde in highly deviated or horizontal wells with a borehole and invasions at the speed of about 4 min/point and with an accuracy of about 3～5％.

现已可用基于SLDMINV的程序，以约4分钟/点的速度和3～5％的精度模拟有井、有侵入的大斜度井、水平井中的感应测井响应。

With the rapid progress of the oil industry, many new and challenging problems began to face the well logging researchers in recent years, such as the development of new types of low frequency electromagnetic tools, the response of traditional induction logging sonde in highly deviated or horizontal wells, the processing technique of crosshole electromagnetic measurements, and the resistivity anisotropy, etc.

随着石油工业的不断发展，新的具有挑战性的问题不断出现在测井研究者面前，如新式低频电磁波测井仪的性能评价，大斜度井，水平井中感应测井的响应特征，井间电磁资料处理方法，电阻率各向异性问题等等。

The floors of the bins shall be of concrete or other approved material having sufficient slope to ensure adequate drainage of aggregates before being used for concreting.

料仓的底面应该是混凝土或者其它批准的材料，具有足够的斜度，以保证骨料在用于浇筑之前能足够地排水。

Place short and long food chips in posterior occlusion of unilateral left side. When the masticated load was 3、5、7 kg, the displacement of abutments was measured by a LB-high sensitive laser transferring detector to calculate displacement, inclination and torsion of the abutment in mesial-distal, labial lingual and vertical and horizontal directions.

分别在左侧后牙区放置长、短食物片的咬合状态下，负载3 kg、5 kg、7 kg咬合力时，用高精度半导体激光位移测量仪测量并计算出同侧基牙在近远中向、颊舌向的水平位移和倾斜、垂直向的位移和水平旋转，统计分析不同牙尖斜度对基牙位移的影响。

Since the entire pad on the wafers must be overprinted to achieve an acceptable reflowed bump size, when overprinting is done on tight pad pitches, the apertures must be positioned with enough space between them so that bridging defects do not occur.

因为晶片整个焊盘应过量印刷锡膏以达到课接受的回流峰尺寸。当焊盘锡膏在焊盘斜度过渡印刷时，孔间应有足够的空间，这样才不会产生连锡。

If you are unfortunate enough to the lovelorn, please tell me, I will help you out, really, please contact me!

如果你不幸失恋了，请告诉我，我会帮助你摆脱困境，真的，请联系我啦！

China's plan to cut energy intensity by 20 percent and pollutant discharges by 10 percent between 2006 and 2010 is a case in point.

中国计划在2006年到2010间降低20%的能源强度和减少10%的主要污染物排放，就是一个这样的例子。