摇臂

It is made up of amoderate breeze gear wheel transmission that the MG400/920-WD typemining machine cuts the cutting department, cut the electricalmachinery of cutting department and put to fix up horizontally inthe rocker arm, the power that the motor outputs leans on a roundof transmission of department of gear wheel and planet round viathe tertiary straight tooth, urge the cylinder to rotate finally.

MG400/920-WD 型采煤机截割部主要是由四级齿轮传动组成，截割部电机放在摇臂内横向布置，电动机输出的动力经由三级直齿圆柱齿轮和一级行星轮系的传动，最后驱动滚筒旋转。

This design firstly fixed ondesign scheme and selected basic components, and besides, developedthe reliability analysis of transmission system. The design ofMG300/701-WD Shearer's cutting unit. It is made up of a gearbox andmoderate breeze gear wheel transmission that the MG300/701-WD typemining machine cuts the cutting department, Cut the electricalmachinery of cutting department and put to fix up horizontally inthe rocker arm, The power that the motor outputs leans on a roundof transmission of department of gear wheel and planet round viathe tertiary straight tooth, Urge the cylinder to rotate finally.

本文首先确定了设计方案和选择了基本部件并开展了传动系统的可靠性分析，MG300/701-WD型采煤机截割部主要是由一个减速箱和四级齿轮传动组成，截割部电机放在摇臂内横向布置，电动机输出的动力经由三级直齿圆拄齿轮和行星轮系的传动，最后驱动滚筒旋转。

On the basis of drawing on the technology and experiences of tower assembling and erection for 500kV and 750kV transmission lines in China, such methods suitable to the tower assembling for UHV transmission line as inside suspension pole with outside pulling wires, ground rocker pole and tower crane are adopted and applied in UHVAC test and pilot project, pursuantly the task of tower assembling and erection in this project is completed, from this a lot of practical experiences are achieved and can be available for reference to subsequent engineering and construction..

文章在借鉴我国500 kV和750 kV架空输电线路组塔施工技术和经验的基础上，提出了内悬浮外拉线抱杆组塔、落地摇臂抱杆组塔、塔式起重机组塔等适合于特高压线路铁塔组立的方法。该方法已在特高压交流试验示范工程中得到应用，为后续工程建设提供了技术储备。

This text mainly discusses how to carry on engineering design to the control system of the radial drilling machine.

本文主要是探讨如何对摇臂钻床控制系统进行工程设计。

This is controled by the rocker arm.

这是由摇臂。

The rocker arm and the connecting rod are important parts of the loader's working device.

摇臂和连杆是装载机工作装置的重要部分，对它们的设计一般用传统的类比法和试凑法。

Process Equipment Design and direct impact on improving the quality and performance valve rocker arm shaft bearings.

现货机械加工行业发生着党课的结构性变化，工艺工装的设计与改良已成为企业生存和发展的必要条件，工艺工装的设计与改良直接影响着气门摇臂轴支座的质量与性能。

One of the heads with rocker arm brackets and spark plugs installed.

其中一名负责人与摇臂括号和火花塞安装。

This setup shows the radius on the end of the rocker arm brackets being cut using the rotary table.

这表明，半径设置的结束摇臂括号被削减使用转盘。

It is supported on 5 rocker arm supporting seats.

支撑在5个摇臂支座上。

What are your goals and strategies for growth?

你的成长目标和策略是什么？

And unto the angel of the church in Sardis write; These things saith he that hath the seven irits of God, and the seven star I know thy works, that thou hast a name that thou livest, and art dead.

3：1 你要写信给撒狄教会的使者，说，那有神的七灵和七星的，说，我知道你的行为，按名你是活的，其实是死的。