定位板

Coupled with the quad seal retainer plate, this alignment assures progressive opening/closing flows, stable throttling, low friction operation and positive closure.

加上四边形密封护圈板，这种对齐定位确保逐级的启/闭流量，稳定的节流，低摩擦操作和积极的关闭。

It's fixed by swing depressor fixtume structure thedespower can be assured by checking computations.

在前述定位基准面选择的前提下，用摆动式压板杠杆夹紧结构，夹紧力经验算可以保证。

It's fixed by swing depressor fixtume structure the despower can be assured by checking computations.

在前述定位基准面选择的前提下，用摆动式压板杠杆夹紧结构，夹紧力经验算可以保证。

Through studying on GPS OEM board and LED display module,the collection and display system of GPS's information are designed.

通过对GPS OEM板和LED显示模块的研究，设计了GPS定位信息的采集与显示系统。

Through studying on GPS OEM board and LED display module,thecollection and display system of GPS's information are designed.

通过对GPSOEM板和LED显示模块的研究，设计了GPS定位信息的采集与显示系统。

5 Create the inferior screw model Bisectioning the included angle between exterior and interior screw and theincluded angle between ecto-upper and ento-upper screw in AutoCAD2006 software,Create a plane traverse the two bisection points and the core of the pedicle.

采用上述辅助定位后如遇椎弓根部穿破情况则需要手动调整螺钉以使螺钉刚好与原穿破侧椎弓根骨壁相切。 1.2.5创建下侧进钉方向的椎弓根螺钉模型：在AutoCAD2006程序中将椎弓根螺钉内外夹角、上方夹角两等分，由同侧两等分点与椎弓根中心点共同创建一平面，依该平面与同侧球在下终板平面交点创建下方螺钉模型。

The design doesn't rely on the packing to position the gate, making packing replacement easier.

这种设计结构不依赖密封填料来定位闸板，因此使得密封填料的更换更加简单。

The included seating angle for the head is standard at 60°.

顶杆的头部用顶料板固定定位，头部陷入凹坑的角度取标准值60°。

IF REPLACING BY PIECE, REPLACE FACE PLATE FIRST USING BACK WELDING,THE SIDE PLATES,EDGE PLATES AND MEMBERS INSIDE SHALL BE STRAIGHTED IF DEFORMED,AND THEN STARTED FITMENT, AND THEN SECURED,WELDING. AT THE SAME TIME, THE CUTTING FLAME SHALL BE CONTROL WHEN CUTTING, AND FORBID TO CUTTING THE BASE

舱盖板整块换新的，可以先换新面板，但面板割除时要采用退割法，里面的侧板、边板和构件如变形需校正后才能装配面板，全部装配好后再定位焊接好，同时在切割的时候尽量控制切割火焰，并严禁割伤母材，从而加大变形量。

Information relating to the Yale and Era cylinder type locks, how to position the lock, drilling the cylinder hole, fitting the cylinder mechanism and mounting plate and also fitting the striking plate/ kepper in the door frame.

有关的资料和时代耶鲁缸式锁，如何定位锁，钻缸孔，配件气缸机制和安装板以及配件的突出板/凯珀在门框。

I am sure after a few weeks of adaptation and familiarization I will have no difficulty in functioning on a daily basis in an English speaking society or in participating fully in graduate studies.

在大学的三年的学习生活不仅给予我自身的充实，更重要的是磨练和培养了我较强的自觉能力和严谨，踏实的作风以及不怕困难的精神，对未来充满了信心！

As the first volcanoes erupted, one of the gases that bellowed out was steam.

在第一批火山喷发时，喷出的气体之一就是水蒸汽。