大圆弧

Based on the method of minimizing maximum workpiece errors,the circular parameters of normal profile of spline hobs are optimized to obtain optimal circular parameters of the hob by analyzing workpiece errors.

通过对工件齿形误差的分析，根据最大误差最小法的基本原理，对矩形花键滚刀法向齿形的圆弧参数进行优化，使滚刀加工出的工件齿形误差最

After the death of purgatory The great pyramid of khufu's four cant is on the east, south, west and north, error less than three points, the arc length 230 meters, the bottom layer due to the tower, now penciling limestone shorter for 227 meters, the Angle of 51 degrees 52 points.

胡夫大金字塔的4个斜面正对东、南、西、北四方，误差不超过圆弧的3分，底边原长230米，由于塔外层石灰石脱落，现在底边减短为227米，倾角为51度52分。

According to the obtained characteristics of focal points and principal planes, using the expressions of focal point, focal plane, focal length, principal point, and principal plane of geodesic lenses, the geometry graphic imaging formation principles of geodesic lenses are developed to get the object-image-relation of geodesic lenses .

利用短程透镜焦点、焦平面、焦距、主点、主平面等的表达式，根据短程透镜在大口径范围内理想聚焦，主平面为以焦点为圆心、以焦距为半径、在原点相切的两个圆弧等性质，推导出了短程透镜物像关系的作图法求取原则。

Horizontal well,and especially available to design the well profiles with combination of arc and straight sections in the vertical expansion plot.

该模型适用于由直线段和圆弧段所组成的各种井身剖面，可广泛应用于斜直井、定向井、水平井、大位移井的设计与监测。

Based on the stress analysis to spired axis mechanism,in the aspect of sliding part which smoothes through alveolus intersection, theresearch of parameters optimization, about the middle alveolus of spired axis andthe dimension of sliding part, has been studied. To the problem that the reverseportion at the both sides of spired axis lashed fiercely and fraies quickly, thearticle finely analyses the best curve of alveolus when adding cushiony spring atthe both sides.

在对螺旋轴机构进行受力分析的基础上，从滑块顺利通过齿槽交叉点的要求方面，对螺旋轴中间段齿槽和滑块的尺寸进行了参数优化分析；针对螺旋轴两端曲线齿槽反向段在高速工作时冲击大、磨损快的问题；从减少滑块在齿槽反向段运动的冲击方面，比较分析了圆弧、抛物线、三角函数等曲线作为螺旋轴齿槽反向段曲线的加速度，提出了较优的(来源：ABCab论bf文网www.abclunwen.com)反向段曲线。

The analysis of the application of grooveless rolling technology proves that grooveless rolling can be successfully realized in the big-distance mills.

通过对无孔型轧制的工业试验和技术分析，得出无孔型轧制可在大间距轧机上实现，脱方控制的关键点是导卫控制和宽展控制，翻平宽展能使轧件产生圆弧钝角，避免了应力集中和裂纹，采用无孔型轧制具有可统一坯料、提高轧辊寿命2～4倍、降低能耗6%～7%等优点。

Then the 3D data from each stereo visionmeasuring unit can be translated into a unique frame of refrence.2. Designed control points of plane form with homocentric arcs and ball markers.By the moment invariants and least-squared procedure of ellipse fit, the markers wererecognized and located automatically with high precision.3. Studied the technology of camera self-calibration, according to the camerawith wide field of view, set up the distorted projection camera model.

通过被测物表面的控制点，将局部测量数据统一到全局坐标系中。2、设计了平面型多重圆弧编码控制点及立体控制点，结合边缘矩的不变性和椭圆最小二乘拟合技术实现控制点的精确定位。3、研究了相机的自标定技术，针对大视场相机的特点，建立了非线性相机成像模型，采用优化算法完成了相机的内、外部参数标定。

The data, which was obtained by calculation, was imitated and the experiential formula for the relation of the max external pressure resisted under the condition of different ratio between straight section length and the end arc radius on the flatted tube.

并对计算分析取得的数据进行拟和得到了扁管在直边段和圆弧半径的不同比值条件下能承受最大外压力的关系及经验公式。

Nalysis and research were made for relation about max external pressure resisting capacity under condition of different ratio between straight section length and end arc radius on the flatted tubes with same circumference and tube wall thickness by using analytical technology of finite element.

bstract 应用有限元分析方法，对相同周长、相同璧厚的扁管在直边段和圆弧半径的不同比值条件下与所能承受最大外压力的关系进行了分析。

The influences of the structural and movement parameters of the arc-track-type flexible holding and conveying mechanism and the sugarcane stalks geometric parameters on the conditions of sugarcane stalks outward windrowing, windrowing angle and distance were analyzed.

对甘蔗在夹持输送终点抛出后和着地时的运动学进行了理论分析，并建立了数学模型，推导出了甘蔗向外铺放的条件，以及甘蔗铺放距离、铺放角的理论计算公式，分析了圆弧轨道式柔性夹持输送装置结构参数、运动参数、甘蔗几何参数对甘蔗向外铺放、铺放距离、铺放角的相互影响规律；对甘蔗在夹持输送过程中的受力情况进行了理论分析，建立了甘蔗在夹持输送装置中所需最小夹持力模型，以及甘蔗质心距柔性夹持元件上端最大距离模型。

What are your goals and strategies for growth?

你的成长目标和策略是什么？

And unto the angel of the church in Sardis write; These things saith he that hath the seven irits of God, and the seven star I know thy works, that thou hast a name that thou livest, and art dead.

3：1 你要写信给撒狄教会的使者，说，那有神的七灵和七星的，说，我知道你的行为，按名你是活的，其实是死的。