填料

The model takes into account the flow and physical property characteristics of the systems as well as geometric variables such as corrugation angle.

根据质量和动量守恒原理，考虑下降液膜和气相的相互作用、系统内气液两相流动、物性特征以及填料结构参数对压降的影响，提出了填料塔内规整填料的压降模型。

For expeller seal combined with packing, adjust degree of tightness of gland in time and replace packing termly, so as to insure a little of clear water through the shaft all the time.

对于付叶轮加填料组合式密封，应及时调整填料压盖的松紧并定期更换填料，以保证始终有少量的清洁水通过轴。

For expeller seal combined with packing, always keep a little of clean water washing along shaft, and termly inspect degree of tightness of gland and replace packing termly. For the mechanical seal, the high pressure sealing water supply should be granted.

对于付叶轮加填料组合式密封，要求始终保持少量清洁水沿轴流过，定期调整填料压盖的松紧并定期更换填料；对于机械密封，要确保高压轴封水的供给。

For expeller seal combined with packing, leakage should be checked in place with packing: before the motor starting, open shaft seal water. If excessive leakage, please tighten gland nuts until guttate leakage.

对于付叶轮加填料组合式密封，应检查填料处泄漏量：启动前，先打开轴封水，如果泄漏量过大，应拧紧填料压盖螺母，直至泄漏呈点滴状为止。

During the auto-control mixing,the parameters of the mixing process,such as rotor speed,filling factor,ram pressure and mix temperature have effect on the mix quality;and the effect of some parameters can be decreased by using instantaneous power control.

瞬时功率控制实质上是对混炼物料粘度的控制。1 瞬时功率控制分析粒状填料能否均匀分散在橡胶中虽然与填料粒子的大小、形状和表面状态有很大关系，但起决定作用的仍然是橡胶的粘度。橡胶粘度太大或太小对粒状填料在橡胶中的分散都不利。

The high density printing and dyeing, the "TB/TA、TB/TH swing the filler freely" applied in the craft of anaerobic hydrolysis in the chemical engineering waste water, this research for the effectiveness of filler optimization was through small and middle sized testing. The fruitage of the study could be used to the selection of filler and application of practical significance in guiding the project.

高浓度印染、化工废水厌氧水解工艺中所应用的"TB/TA、TB/TH自由摆动填料"，通过小试、中试实验对多种填料进行效能优化研究，该实验结果对填料的选型及实际工程，特别是在成分复杂多变的印染、化工废水处理工程中的应用具有重要的指导意义。

Gland – two piece gland bushing/packing flange is self-aligning to prevent stem damage for cocked gland.

填料压盖-两件式填料压盖衬套/填料法兰能够自动校准，以防止由于填料压盖翘起造成阀杆损坏。

Stuffing mainly by the packing, seal ring, filling cylinders, packing gland, water-sealed tube.

填料函主要由填料，水封环，填料筒，填料压盖，水封管组成。

Topological optimization system of variable density method based on finite element software;2. Interface depths inversion of potential field data with variable density model;3. According to the characteristics of the cold insulation box of Fractionating tower, it is considered that the effect of inner-filling on the construction is related with the variable density, then the relative formulation in the condition of n.

根据分馏塔保冷箱的特点，认为内填料对结构的作用与变密度有关，推导了无水平位移下的相关公式；对此结构在有水平位移下内填料的发育进行仿真分析，并将内填料的作用与结构的楼层柱的旋转角建立联系；最后根据得到的结论对分馏塔保冷箱在风与内填料作用下进行了非线性分析，得到结构的极限承载力。

Check the seal filling for proper seal condition.If too loose,press down the filling cover properly.Renew the filling after operating for the month.

检查密封填料的密封情况，如太松，应适当压紧填料压盖，每运行一个月，应将旧填料取出换上新填料。

Methods: Five patients with parkinsonism or dystonia were assigned to general anesthesia using an modified endotracheal tube.

本实验依照人体实验之相关规定进行，五位患有帕金森氏症或肌张力异常的病人接受神经立体定位手术。

If you can benefit from this book, it is our honour.

如果您能从本书获益，这将是我们的荣幸。