基本单元

In the second chapter, elementary theories and ideas of one step forming inverse approach were described and warped modification method, implemented by Cook, was introduced into one step forming simulation and based on idea of surface spreading; new quadrilateral element modification arithmetic was put forward. By spreading warped quadrilateral onto plane in local coordinate system, a plane quadrilateral element whose shape and area were equal to original warped quadrilateral element was gotten and internal force vectors of four nodes and stiffness matrix of elements were improved to increase precision of simulations on this plane element.

第二章从一步成形逆有限元法的基本理论和思想出发，将Cook基于弹性理论的四边形单元的翘曲修正算法引入基于塑性的一步成形，并且基于曲面展开的思想，本文提出一种新的四节点单元翘曲修正方案，通过把翘曲的单元展开的方法在局部参考系中得到一个与实际翘曲单元的形状与面积非常接近的平面单元，在该平面单元中进行单元刚度及内力向量的计算，进一步改善模拟结果的精度。

Firstly it describes the development ,basic principle and application and propagation characteristic of mobile channel , then investigates the system structure of DAB transmitter and receiver separately and the key technology of realization of the digital audio broadcast system.And then discusses the system component of FFT －the demodulation module of OFDM .The 409- points FFT module employs a radix-4 decimation-in-frequency algorithm, includes arithmetic element , read and write address element ,twiddle factor element and control element , is realized by FPGA. In the end , the result is verified in the matlab .

首先概述了OFDM的发展、基本原理和应用以及移动信道的传播特性，接着分别研究了数字音频广播接收机和发射机的系统结构，以及数字音频广播系统实现的关键技术，然后详细论述了OFDM解调模块FFT的系统结构，主要研究了4096点FFT采用基－4按频率抽取实现的算法，整个FFT模块包括了运算单元、读写地址单元、旋转因子单元以及控制单元，并且在FPGA中进行了硬件实现，并在matlab环境下对结果进行了验证。

The geology research of carbonate reservoirs in Ordovician of Tahe oilfield showed that many large dissolved vugs and fractures were developed. The spread of the reservoir take on a very heterogeneous state. And the typical fractured-vuggy reservoirs was formed. According to the combination of the various spaces, the formation was divided into vuggy formation, fractured-vuggy formation and fractured formation. The research showed that development of the vug is relevant to the its position on the structure, the fractures, the water surface and the weathering surface. Multi-phase charge and recharge of the oil in the reservoirs resulted in the complexity of the fluid distribution. So the"Bottle Model"was brought forward to explain the movement of the water-oil contact. The special storage space and the complex fluid distribution lead to the unstability of the production and the complexity of the water cut. In order to explain the characteristic of the fracture-vug unit was brought forward and the basic principle and method of the partition of the fracture-vug unit was formed. The classification and evaluation of the units were performed according the reserve and energy. Based on the research of geology characteristic and the fluid flow in the reservoir the comprehensive numerical simulation plan of the fractured-vuggy reservoirs were established. Through the selection of the simulation unit, fluid flow type and parameter equivalent the triple media reservoir simulation model was established. Considering the practical application the model was resolved by the DKR decomposition conjugate grads method. Based on the fine reservoir description of Dsitrict IV of the Tahe oilfield the various space type were classified and combined together. The geology model of Unit S48 was constructed. Two typical single well model was established according to the geology and the dynamic phenomena. Finally the single well model and the Unit S48 were simulated by the triple media reservoir simulator. Via the local grid refinement and coarsening in the simulation good matchs were gained. Based on the results of the simulation the reserve distribution, percent of reserve produced in various space and the natural energy were analyzed. The fluid was storaged in the fractures and vugs mostly and more than 90% the produced oil came from the systems. The energy belonged to the active one. The results of simulation accorded with the fact and showed the validity and practicability the research and the simulator.

塔河油田奥陶系碳酸盐岩油藏的地质研究表明，其储层中发育着很多大型的溶蚀洞、缝，储层的平面展布呈现出极度的非均质性，形成了典型的缝洞型碳酸盐岩油藏，根据各种孔隙介质在储层中的组合，将储层分为了溶洞型、裂缝-溶洞型和裂缝型三类；研究表明溶洞储层的发育和构造位置、裂缝的发育、潜水面和风化面的位置等因素有关；多期充注的油气成藏模式导致了流体复杂的赋存状态，由此提出了所谓的"瓶子模型"，解释生产过程中油水界面的变化；特殊的储集空间类型和流体分布特征导致油田在开发过程中表现出很大的不确定性和含水变化的复杂性，为了合理的解释油气田开发过程中的动态特征，提出了"缝洞单元"的概念，并制定了"缝洞单元"纵横向划分的基本原则和依据及划分方法，并对"缝洞单元"进行了分类和评价；基于地质特征和流体在其中流动规律的研究，提出了缝洞型碳酸盐岩油藏的数值模拟综合解决方案，通过模拟单元的选择、流动类型和参数的等效，建立了三重介质油藏三维三相数值模拟模型，采用不完全LU分解预处理共轭梯度法进行了求解；在塔河油田4区精细油藏描述的基础上，将各种类型的孔隙空间进行了归类组合，建立了S48单元的地质模型；通过对油井生产动态进行分析研究，建立了两类和油井地质、生产动态相对应的单井模型；最后应用三重介质油藏数值模拟软件对单井模型和S48单元进行了数值模拟，通过局部加密和粗化等技术模拟流体流动规律，取得了很好的拟合效果；结合数值模拟结果，分析了各种介质中的储量分布、储量产出的百分比以及地层的能量，认为塔河油田缝洞型油藏中流体绝大多数储集于缝洞系统之中，所产出流体90%以上也来自于缝洞系统，其底水能量属于较充足的类型；模拟结果和油田实际情况符合较好，说明了地质研究和油藏数值模拟研究的正确性。

The geology research of carbonate reservoirs in Ordovician of Tahe oilfield showed that many large dissolved vugs and fractures were developed. The spread of the reservoir take on a very heterogeneous state. And the typical fractured-vuggy reservoirs was formed. According to the combination of the various spaces, the formation was divided into vuggy formation, fractured-vuggy formation and fractured formation. The research showed that development of the vug is relevant to the its position on the structure, the fractures, the water surface and the weathering surface. Multi-phase charge and recharge of the oil in the reservoirs resulted in the complexity of the fluid distribution. So the"Bottle Model"was brought forward to explain the movement of the water-oil contact. The special storage space and the complex fluid distribution lead to the unstability of the production and the complexity of the water cut. In order to explain the characteristic of the fracture-vug unit was brought forward and the basic principle and method of the partition of the fracture-vug unit was formed. The classification and evaluation of the units were performed according the reserve and energy. Based on the research of geology characteristic and the fluid flow in the reservoir the comprehensive numerical simulation plan of the fractured-vuggy reservoirs were established. Through the selection of the simulation unit, fluid flow type and parameter equivalent the triple media reservoir simulation model was established. Considering the practical application the model was resolved by the DKR decomposition conjugate grads method. Based on the fine reservoir description of Dsitrict IV of the Tahe oilfield the various space type were classified and combined together. The geology model of Unit S48 was constructed. Two typical single well model was established according to the geology and the dynamic phenomena. Finally the single well model and the Unit S48 were simulated by the triple media reservoir simulator. Via the local grid refinement and coarsening in the simulation good matchs were gained. Based on the results of the simulation the reserve distribution, percent of reserve produced in various space and the natural energy were analyzed. The fluid was storaged in the fractures and vugs mostly and more than 90% the produced oil came from the systems. The energy belonged to the active one. The results of simulation accorded with the fact and showed the validity and practicability the research and the simulator.

塔河油田奥陶系碳酸盐岩油藏的地质研究表明，其储层中发育着很多大型的溶蚀洞、缝，储层的平面展布呈现出极度的非均质性，形成了典型的缝洞型碳酸盐岩油藏，根据各种孔隙介质在储层中的组合，将储层分为了溶洞型、裂缝-溶洞型和裂缝型三类；研究表明溶洞储层的发育和构造位置、裂缝的发育、潜水面和风化面的位置等因素有关；多期充注的油气成藏模式导致了流体复杂的赋存状态，由此提出了所谓的&瓶子模型&，解释生产过程中油水界面的变化；特殊的储集空间类型和流体分布特征导致油田在开发过程中表现出很大的不确定性和含水变化的复杂性，为了合理的解释油气田开发过程中的动态特征，提出了&缝洞单元&的概念，并制定了&缝洞单元&纵横向划分的基本原则和依据及划分方法，并对&缝洞单元&进行了分类和评价；基于地质特征和流体在其中流动规律的研究，提出了缝洞型碳酸盐岩油藏的数值模拟综合解决方案，通过模拟单元的选择、流动类型和参数的等效，建立了三重介质油藏三维三相数值模拟模型，采用不完全LU分解预处理共轭梯度法进行了求解；在塔河油田4区精细油藏描述的基础上，将各种类型的孔隙空间进行了归类组合，建立了S48单元的地质模型；通过对油井生产动态进行分析研究，建立了两类和油井地质、生产动态相对应的单井模型；最后应用三重介质油藏数值模拟软件对单井模型和S48单元进行了数值模拟，通过局部加密和粗化等技术模拟流体流动规律，取得了很好的拟合效果；结合数值模拟结果，分析了各种介质中的储量分布、储量产出的百分比以及地层的能量，认为塔河油田缝洞型油藏中流体绝大多数储集于缝洞系统之中，所产出流体90%以上也来自于缝洞系统，其底水能量属于较充足的类型；模拟结果和油田实际情况符合较好，说明了地质研究和油藏数值模拟研究的正确性。

It effectively solves the problem of contact mechanics between burden granules. The dynamic data structure that is a linked list is built to save and delete the varying data in simulation calculation process. Therefore, the distinct element method simulation model of charging bell-less top blast furnace is established in view of the distinct element method model of blast furnace burden granular.

本文首先对离散单元法的基本原理和数值计算方法进行了系统研究，针对高炉炉料颗粒介质特点，对离散单元法进行了相应改进，建立了高炉炉料颗粒运动的离散单元法基本数学模型，推导出了相应的高炉炉料颗粒离散单元法数值计算基本参数的计算公式，例如阻尼、刚度、时步等，并确定了合理的数值模拟参数值。

The foundational method to construct Command and Control Relationships Network Model is discussed.Entity elements of organizations are divided into Scouters,Decision Makers and Actors.Two dimensions of the power,"influence" and "domination",are studied in the point of sociological view,the conception of C2 relationships is redefined.

研究了构建C2组织的指挥控制关系网络模型的基本方法，将组织的实体要素划分为侦察单元、决策单元和执行单元三类；从社会学的角度分析了C2组织中指挥控制权力的&影响&和&支配&两个维度，并重新定义了指挥控制关系；将实体单元和单元之间的指挥控制关系抽象为网络模型的点和边。

The basic unit of quantum electromagnetic field is obviously a kind of matter in structural realism, therefore, the basic unit (electromagnetic element-wave) of classical electromagnetic field should be certainly a kind of matter, too.

摘 要：在结构实在论中，量子电磁场的基本单元——&光子&显然是一种物质。

Cascades are the basic unit of heat-work conversion in turbomachinery, and therefore its aerodynamic design theory and methodology has been the key subject in the area of turbomachinery aerothermodynamics all over the world.

叶栅作为叶轮机械热功转换的基本单元，其气动设计理论与设计方法的研究，一直是国内外叶轮机械气动热力学领域关注的重点。

Family is a basic unit of society.

家庭是社会的基本单元。

The family is the basic unit of our society.

家庭是社会的基本单元。

Cynanchum Lingtai apricot production in the average weight 65 grams, the brightly-colored fruit, juicy rich, sweet-sour taste, sweet from the nucleolus, when the late Qing Dynasty famous Shaanxi, Gansu provinces, the Qing imperial court Tongzhi tribute for years.

灵台生产的牛心杏平均单果重65克，果实色泽鲜艳，汁多味浓，甜酸适口，离核仁甜，清末时就驰名陕、甘两省，清同治年间曾为朝廷贡品。

Chenopodium album,Solanum nigrum, and Amaranthus retroflexus were very susceptible to the herbicides. Polygonum persicaria and Abutilon theophrasti were relatively less susceptible to the herbicides, and Lycopersicon esculentum was not susceptible to it. The relationship between reduction rates of weed biomass and PPM values of weed leaves 2,4, and 6 days after treatment was established.

供试的6种杂草对该混剂的敏感性存在显著差异：红心藜Chenopodium album、龙葵Solanum nigrum和反枝苋Amaranthus retroflexus对该混剂最敏感，ED90值分别为47.65、71.67和29.17g/hm2；春蓼Polygonum persicaria和苘麻Abutilon theophrasti敏感，ED90值分别为96.91、114.20g/hm2；而番茄不敏感。