均匀地

Numerical simulation for nonuniformly injected SOAs is an important basis for the device characterization, fabrication, and applications. We can conveniently and fleetly obtain the device characters and the effects of each design parameter through numerical simulation.

对非均匀注入SOA的数值仿真是研究其器件特性、器件制作、拓展其应用的重要基础，通过数值仿真我们可以方便快捷地获得器件的特性及各参数对其特性的影响，运用分析的结果来指导器件设计。

A signal reconstruction algorithm based on the output signal spectrum is studied, the experiment data prove that the algorithm can reconstruct the nonuniformly sampling signal, the research of this algorithm provided theory basis for its application

研究了一种基于系统输出序列频谱的滤波重构算法，通过原型电路的实际数据，证明该算法可以有效地重构非均匀采样信号，为该算法的应用提供了理论基础。

Polystyrene-MMT nanocomposites were prepared by free radical polymerization of styrene containing dispersed clay. The organophilic MMT particles were easily dispersed and swollen in styrene monomer.

采用双－苯基二甲基十八烷基溴化铵作为有机插层剂对钠基蒙脱土进行了有机化处理，该有机化的蒙脱土粒子在苯乙烯单体中很容易地均匀分散并形成稳定的胶体溶液。

The range depicted on the following photograph (Photo 1) comprises of a suitable entry unit provided with centrally driven unwinding unit as well as tension adjusting elements that ensure an even supply of fabric into the padder.

下面图片所示的是冷轧堆染色机，其进布装置配有中央退卷装置和张力调节装置，以此保证织物均匀平稳地进入轧车，织物在通过轧车后经导辊被送至打卷装置，针织物在A型架上打卷，随布卷增大，A型架由初始位置恒速背离轧辊前行。

Because ammonium paratungstate is difficult to dissolve in water,the chemical reaction of acid decomposition APT to H2WO4 is solid-liquid reaction and hinder the reaction uniformly and effectively carrying on.

李玲 APT在水中的难溶性使得酸分解APT制取钨酸的化学反应成为固－液反应，从而妨碍了反应均匀有效地进行。

The results show that the surface quality of phosphating film is obviously improved by ZY, and a uniform and compact coating can be obtained when phosphated at 20℃ for about 20 minutes, which is 1.09 g/m^2 in weight, can withstand CuSO4 solution dropping for above 200 s, and resist mass fraction of 3% NaCl solution soaking for more than 5 hours.

结果表明，成膜助剂ZY明显地改善了磷化膜的表面质量，在20℃、磷化20min时可以获得均匀致密的磷化膜，膜重为1.09g/平方公尺，耐CuSO4点滴时间超过200s，质量分数为3%的NaCl溶液浸泡时间超过5h。

In this paper,surface line-charge method was taken to calculate the magnetic distribution in a 160kA large prebake anode aluminum reduction cell in Guizhou Aluminum Smelter.

应用表面磁荷法对贵州铝厂 16 0kA大型预焙阳极铝电解槽的磁场进行了计算，通过对电流分布均匀情况下和考虑了实际电流分布情况下的电解槽磁场的比较，可以看出，阳极和阴极电流分布对铝电解槽磁场分布具有绝对的影响，只有在考虑了阳极和阴极电流实际分布的情况下，才能准确地计算出铝电解槽的实际磁场分布。

The results show that Sb addition can diminish the crystal grain, but the content of segregative phase at crystal boundary increases, and the current efficiency of material is low. Compared with Sb addition, Sn addition can also diminish the crystal grain, the current efficiency increases, the content of segregative phase at crystal boundary reduces, but diffusional corrosion of the anode surface is not uniform. The cooperation of Sb and Sn can prevent Si from segregating effectively and enhance the current efficiency obviously. At the same time, anode materials have preferable surface dissolution characteristics.

结果表明： Sb具有细化晶粒的作用，但晶界存在较多偏析相，电流效率偏低；与Sb相比较， Sn也具有细化晶粒的作用，电流效率有所提高，晶界偏析相较少，但阳极的表面腐蚀溶解不均匀； Sn和Sb的协同作用在于能有效地抑制Si的偏析，显著提高阳极的电流效率，使得阳极表面具有良好的腐蚀溶解性。

The water chamber takes the shape of tilting cube, in favor of uniform distribution of cooling water on tube plate surface. The tube bundle is divided into two groups of zygomorphy according to the bisection system and it has eight support clapboards. The siphonopore center of each clapboard increases a certain distance corresponding to that of two tube plates and the cooling tube takes the shape of arch. The two-way cooling water of bisection flows through the condenser in opposite direction so as to improve the distribution of heat load for tube bundle. Around the throat of condenser, the final stage low-pressure heater, air extraction tube, intake device of bypass exhaust and the like are deployed.

它的特点是：水室呈倾斜立方体形状，有利于冷却水流在管板面上均匀分布；由于采用对分制，管束相应地分为左、右对称的两组，并且管束设有八块支撑隔板，每块隔板的管孔中心相对于两端管板的管孔中心依次抬高一定的距离，以使冷却管呈拱形状；对分制的两路冷却水以相反方向流过凝汽器，从而改善管束的热负荷分布；在凝汽器喉部布置了末级低压加热器，抽汽管道及旁路排汽接受装置等。

The experiments show that too high cooling rate disadvantages the formation of spherical primary crystals, while higher mechanical stirring strength is necessary to spheroidize and homogenize the primary crystals.

较高的搅拌强度可以有效地减小初晶硅的尺寸，并使之边角钝化和均匀化；但当冷却速率太大时，由于搅拌时间缩短，则不利于球形初生相颗粒的生成。

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。