啮合

These designing parameters include stiffness of epicyclical bearings, synthetic meshing stiffness of gears, stiffness of supporting bearing of out put shaft, mass of inner rack, meshing angle of gears, distance between inputting shaft and supporting shaft and input speed etc..

这些设计参数包括：行星轴承刚度、齿轮综合啮合刚度、输出轴支承轴承刚度、内齿板质量、齿轮啮合角、输入轴和支承轴间距及输入转速等，根据这些分析，可以提出改善三环传动动态性能的可能途径。

It is proved that the method using the BEM to calculate the load distributions on the contact lines of involute gear pair, in which the applied load is taken in the form of a concentrated one at a single node, is not suitable. A method in which the tractions of the BEM are made to imitate the Hertzian pressure of the gear using 8 nodes isoparametric elements is introduced.

本文解决了边界元法在空间啮合副计算中存在的系数矩阵的存储，奇异单元积分的计算、表面不连续点处面力一点多值和求解未知量的线性方程组矩阵元素的计算等问题，编制了比不采用上述处理方法的一般边界单元法节省近一半内存和计算时间的适合空间啮合副的三维边界元法计算程序。

Then calculates clearances in radius direction for all kinds of nonparallel degree between input shaft and output shaft, and presents conditions of adjustability. Applies the experimental device, which is developed for this paper research, as example, introduce calculation formulation of overlapping coefficient and pressure angle while the distance between two centers is uncertain, in this way, we get the range of the center distance.

以本论文的实验研究装置为例，引入了中心距不确定状况下的重迭系数、压力角等计算公式，以两齿轮啮合时的分度圆不能相割为最小中心距，以两齿轮啮合的重迭系数不小于1为最大中心距，从而得到相应的中心距范围。

But the involute gear exposes certain own defaults too, such as the external toothing transmission is the engaging transmission of the protruding tooth to the protruding tooth, its contact stress is big,bearing capacity is low etc.

但是渐开线齿轮也暴露出自身一些缺点，如外啮合传动是凸齿对凸齿的啮合传动，其接触应力大，承载能力低等缺点。

On the base of simply introducing running transmission mechanism of shearer,according to the theory of rack and pinion engagement,mainly analyses impact cause resulted from toothing between shearer involute sprocket and conveyor pin-rail ,using the specific parameters.

简单介绍了目前大功率采煤机的行走传动装置，并结合某采煤机渐开线行走轮和输送机销排销齿的具体参数，按照齿轮齿条啮合理论，分析了此渐开线行走轮和销齿啮合产生冲击的原因之一。

In order to solve the technical problems of cold pressing of de-hulled double-low rapeseed ,a new twin-screw press with a principle of combination of joggling and non-joggling was designed and manufactured,the pressing chamber of which had characteristics of multiple-stage compression and relaxation and a thin layer of when pressing.

为实现双低菜籽脱皮后的冷态压榨，研制了一种双螺杆榨油机，采用啮合式和非啮合式相组合的原理，在榨膛内实行多级压缩和松弛及薄料层压榨，其理论压缩比达23.0，榨膛长径比达11.5，压榨时间达180 s，并具有强大的物料自清功能，解决了脱皮菜籽仁在榨膛内输送困难的问题。

Utilizing the extremum theory of function to obtain the minimum radius of curvature of theoretical profile, and factors that affecting the minimum radius of curvature were discussed, thus provided theoretical basis for the studies of the continuous contact transmission of swinging movable teethed central gear meshing pair, contact stress and meshing stiffness etc..

利用函数极值理论得到理论廓线的最小曲率半径，讨论了最小曲率半径的影响因素。为摆动活齿中心轮啮合副的连续接触传动、接触应力和啮合刚度等的研究提供了理论基础。

The company mainly produces chemical process pumps, high pressure reciprocating pump, piston metering pumps, hydraulic diaphragm metering pumps, mechanical diaphragm metering pumps, gear pumps, meshing, the meshing gear pumps, small flow pump, single screw pump, double-headed Screw pump, three screw pump, shielding pump, magnetic pumps, liquid pumps, boiler feed water pump, steam reciprocating pump, fluorine plastic pump, slurry pumps, water treatment and medicine, environmental protection equipment, industrial pumps accessories, annex Buffer, back-pressure valve, filter, check valves, safety valves, instrumentation, and other on-line

公司主要生产化工流程泵、往复式高压泵、柱塞计量泵、液压隔膜计量泵、机械隔膜计量泵、内啮合齿轮泵、外啮合齿轮泵、小流量离心泵、单螺杆泵、双头螺杆泵、三头螺杆泵、屏蔽泵、磁力泵、液下泵、锅炉给水泵、蒸汽往复泵、氟塑料泵、渣浆泵、水处理加药系统、环保设备、工业泵配件、附件缓冲器、背压阀、过滤器、止回阀、安全阀、在线检测仪表等

Thusthe bearing capacity of three-ring gear drive is increased by this phenomenon, whichmay be called Elastic Meshing Effect.

我们将啮合齿轮因弹性变形多齿承载引起的齿轮承载能力提高的现象称为弹性啮合效应。

The engagement theory of the gear rack mechanism can be used to study the silent chain mechanism.

基于齿轮齿条机构的啮合理论，研究了渐开线齿形链机构的啮合机理。

I will endeavour to find you some assistance.

我尽力帮你找人帮忙。

At first I only know bruck is the idol of American younglings, afterwards I returned back to Taiwan ,even in Beijing last year ,I saw her poster everywhere, I was so surprised at her charm.

起初我只晓得布鲁克雷德丝是美国少男少女崇拜的偶像，后来回台湾，甚至去年在北京，居然也四处看见她的海报，才惊讶她的魅力之大。