英语人>网络例句>啮合 相关的搜索结果
网络例句

啮合

与 啮合 相关的网络例句 [注:此内容来源于网络,仅供参考]

This practical new-pattern power input axis 1 is assorted with furrow whole machine batholith 46 power fitting machine support 26 install rototiller axis 21 gear box 4,17 There are glide assorted umbrella gears 5, tooth border away-combine talon 7 and spring in axis .umbrella gears 5 and power input axis end of umbrella gears 11 mesh , the other end of axis with umbrella gears 42 mesh umbrella gears14 on rototiller axis 21, on axis 21 installs revovle furrow sword 23, on the shelf is tail wheel 29.tooth border away-combine talon 7 is driven by branch arm 35 on dial fork axis 34, branch arm is controlled by handle 38, connect part 39, control hold 36, it has orientation part .

本实用新型动力输入轴1与耕整机底盘46动力装置配合。机架26上装有旋耕轴21,齿轮箱4,17。轴1有滑动配合的伞齿轮5和牙镶离合爪7,有弹簧8。伞齿轮5与动力输出轴13端部的伞齿轮11啮合,轴13另一端有伞齿轮42与旋耕轴21上的伞齿轮14啮合,轴21上装有旋耕刀23,上有尾轮29。牙镶离合爪7由位于拨叉轴34上的支臂35驱动,支臂由手柄38,连接件39,操纵把36控制,有定位件45。

Taking cydid gear-pin rail chainless traction mechanism of MG375W as an example, make theoretical deduction for the profile and the kinematic characteristics of the cycloid gear , and make simulation analysis for some different engaging positions by computer.

以MG375W采煤机的摆线轮与销排无链牵引机构为例,进行了摆线轮齿廓特性及运动特性的理论推导,对不同的啮合工位进行了计算机模拟仿真分析,得出了中心距及节距发生变化引起啮合传动特性的变化规律。

This paper describes a meshing analysis of the contrate harmonic gear drive which can quickly select the optimum transmission and determine the corresponding meshing parameters and structure parameters.

建立的端面谐波齿轮传动的啮合分析软件,可以较快地选取最佳传动方案,确定相应的啮合参数和结构参数。

On the basis of the mathematics model of contrate harmonic gear drive, the change law of meshing backlash of contrate harmonic gear was analyzed by meshing analysis software.

据板壳理论采用高度变位对刚轮和柔轮进行变位,在端面谐波齿轮传动数学模型基础上,用啮合分析软件分析端面谐波齿轮啮合侧隙的变化规律。

The paper provides a meshing analysis of the contrate harmonic gear drive which can quickly select the optimum transmission scheme and determine the corresponding meshing parameters and structure parameters.

广东技术师范学院,广州 510665; 2。佛山市财经学校,佛山 528000)摘要建立的端面谐波齿轮传动的啮合分析软件,可以较快地选取最佳传动方案,确定相应的啮合参数和结构参数。

Cycloidal pump has been applied in hydraulic system widely because of its many advantages.

0引言摆线齿轮泵是一种输送流体的内啮合齿轮泵,它具有体积小、流量大、结构紧凑、啮合重叠系数大、传动平稳等特点,在液压系统中广泛应用。

In order to reduce the difference of stress level of sabot dedendum surface remarkably and the stress of dangerous dedendum surface greatly, interval meshing technology was applied to the composite sabot of high power armor piercing projectiles.

为有效地降低复合材料弹托发射过程中齿根面应力水平的差异,将啮合间隙技术应用于大威力穿甲弹的复合材料弹托上,给出了间隙啮合技术应用的一般步骤和方法。

It consists of three parts firstly,a large number of meshing data were measured out through three dismountable teeth installed along the radial direction of rigid wheel under loading status,secondly,the experimental curves of tangential force t and of radial force r inside meshing zone were gained by means of method of mathematica...

包括三部分:首先,在载荷状态下,通过安装在刚轮径向方向上三个可装、拆的活齿,测得大量的啮合数据;其次,通过数学统计方法获得啮合区内切向力Ft和径向力Fr的实验曲线;最后,应用函数逼近法获得载荷区内载荷分布方程

On the basis of an analysis of theoretic clearances and teeth deformation, amathematic model was developed in this thesis to describe the state of multi-toothcontacting and load distribution, and a method was proposed to involve the EME ingear strength evaluation.

本文在考虑内外齿轮工作齿廓理论间隙、轮齿弹性变形的基础上,建立了三环传动弹性啮合的理论分析模型,得到了同时啮合的齿对数和各齿对上的载荷分配情况。

It is an important but difficult job to compute the transmission ratio and the meshing efficiency of epicyclic gear trains.

周转轮系传动比与啮合效率(只考虑轮齿啮合摩擦损失)的计算方法卜3 J较多,但都比较沉繁。

第5/40页 首页 < 1 2 3 4 5 6 7 8 9 ... > 尾页
推荐网络例句

I will endeavour to find you some assistance.

我尽力帮你找人帮忙。

At first I only know bruck is the idol of American younglings, afterwards I returned back to Taiwan ,even in Beijing last year ,I saw her poster everywhere, I was so surprised at her charm.

起初我只晓得布鲁克雷德丝是美国少男少女崇拜的偶像,后来回台湾,甚至去年在北京,居然也四处看见她的海报,才惊讶她的魅力之大。

Ah may dee:You are chinese living in a democratic country.

你是居住在民主国家的中国人吧。