动态测试

It can test barbette" s dynamic performance by serval ways. During testing, the system control barbette" s moving and acquire the real-time data. And reflect the systems state on the friendly system interface.

在测试过程中，完成对炮塔的各种动态控制以及现场性能数据的实时采集，并通过友好的系统界面向工作人员实时反映整个测试过程的运行状态。

It was found that the correlation between the dynamic and static test results was high.

测试结果表明，动态与静态测试结果之间的相关程度较高。

It can realize the real-time measurement and data storage,and the dynamic state of the dynamometer is well.

摘 要：基于电动车辆用系统稳态和动态性能测试台架实现同一平台的包括电机驱动和发电特性的测试要求。

Then, a test system with various types of sensor interface was built, which had the ability of displaying rolling-angle and drawing the error curve dynamically.

试验结果表明：该系统可以在转速为0～50 r/s的情况下达到±0.036°的测试精度，为姿态传感器的研制、动态性能检测提供了有效的测试手段。

A new projectile-filling device was developed to realize the fracture perforating under the condition of high foramen density.

提出了一种新型装药结构并实现在高孔密条件下的复合射孔，所开发的产品进行了地面混凝土靶测试、地面动态压力-时间过程测试和现场应用试验。

This new-style intelligent work charactor testing device for furl pump valve has high testing efficiency, low error.

这种新型的燃油泵阀门工作特性的智能测试装置，检测效率高、误差小，不仅能检测燃油泵阀门的静态性能，还能对其动态性能作测试，适合于燃油泵装配生产线上的在线检测，从而可从根本上克服传统检测方式的缺陷，以正确掌握阀门的工作性能与状态。

With the compare of research methods such as direct experiment, indirect method and numerical simulation method, and with the applied background of the Virtual Prototype technology, the paper puts forward a new strategy for the design of the testing device for dynamic response of road based on Pro/E、 ADAMS and ANSYS software. On the basis of the theory, this paper analyze the scheme and the important parts, and has proposed that actual modeling parameter, pattern and arrangement scheme, and structured the complete machine scheme of a testing device for testing road dynamic response based on dynamic load of vehicle-road.

本文在系统分析了各种车路系统动载荷研究方法的基础上，针对直接试验方法、间接试验方法和数字仿真方法的发展，并结合"虚拟样机"技术的应用背景，提出了一种基于Pro／E、ADAMS和ANSYS软件的基于车路动载荷的测试路面力学响应的试验装置的虚拟样机的实现策略，并在此基础上，对方案和重要部件进行了分析，提出了实际的建模参数、型式和布局方案，构建了一种基于车路系统动力学的测试路面动态力学响应的试验装置的整机方案。

The luminescence power of semiconductor laser diode is tested after the radiator element of laser diode is made and the drive circuit is designed. Then, chaos mathematic model is introduced to produce deterministic class stochastic signal and C langrage program, which is based on the hardware circuit design of MSP430, is designed and on-line debugged to implement the dynamic stimulation effect and avoid the body adaptability with the duty cycle of chaos sequence. The duty cycle is adjusted and controlled to accomplish the reinforcing and reducing in moxibustion. At last, Average power of laser diode is tested under the conditions of different duty cycles and the waveforms are collected by applying virtual instrument.

在半导体激光器散热装置的特别制作及工作驱动电路的设计基础上，完成半导体激光器发光功率的测试，然后引入混沌数学模型方法来产生确定性的类随机信号，在 MSP430 单片机硬件电路设计的基础上，应用单片机 C语言进行程序设计并在线调试，实现传统灸法的动态刺激效果，采用混沌序列占空比信号消除人体适应性，调整和控制输出占空比的改变以达到灸疗的补泻手法的实现，最后对不同控制占空比情况下激光器输出的平均功率进行测试，完成工作波形的采集。

The heat generation curves of seven rubber materials used in tires with the changes of temperature have been obtained by using Dynamic Mechanics Analysis technique on NETZSCH DMA242 instrument, knowing that the heat generation of every other rubber materials except inner liner rubber changes lightly alone with the temperature within 10℃～80℃. According to the Fourier law, the heat transfer coefficients of tire rubber are measured by stable method on self-made experiment instrument. The coefficients changes lineally within 20℃～80℃ and the relation formulas λ=λ〓+bt are given out attached with λ〓 and b. The specific heat of tire rubber are measured on Differential Scanning Calorimeter NETZSCH DSC204 and the relations with temperature are linear and the formula is c=c〓+bT, where c〓 and b gained from experiment result data are presented in the paper. The heat convection coefficients on the surface of rolling tire are measured according to the principle of heat-mass transfer analogy principle after simplifying rolling tire into rotating disk with straight movement on wind channel. The relation with rotation speed of disk is linear as h=5. 399+0.0258n and the relation with straight line speed of tire is linear too, h=

论文采用动态力学分析技术，使用NETZSCH DMA 242型实验仪，获得了轮胎用七种胶料的生热率随温度变化曲线，确知除内衬层胶以外，其它各种胶料在一般胎温范围内（10℃～80℃）的生热率随温度变化不大；轮胎胶料的导热系数根据傅立叶定律的基本原理，采用稳态法在自行搭建的实验台上进行测试，结果表明，材料的导热系数在20℃～80℃的温度范围内随温度呈线性变化，论文给出了各种材料导热系数的线性变化的关系式λ=λ〓+bt及其λ〓和b的值；轮胎胶料的比热运用差式扫描量热原理，在NETZSCH DSC204型DSC实验仪上进行测试，结果表明，胶料的比热随温度的变化呈线性变化，其关系可用c=c〓+bT表示，文中给出了根据实验数据拟合的c〓、b的值；对轮胎表面的对流换热系数的测定，本文先将滚动的轮胎简化为有直线运动的旋转圆盘，而后采用萘升华热质比拟技术，在风洞中测量了滚动轮胎表面的对流换热系数，结果表明，圆盘表面对流换热系数与转速呈线性关系，即h=5.399+0.0258n，轮胎表面对流换热系数与其直线运动的速度呈线性关系，即h=

To provide optical fiber: Fiber Distributed Temperature Stress Test System, Fiber Distributed Temperature Measurement System, Fiber Bragg Grating Health Monitoring System, fiber optic geophone systems, fiber Bragg grating wavelength calibration instrument and so on, which sensor product line is extremely rich and has industry representation, including: fiber optic temperature hygrometer, fiber-optic gas alarm, fiber-optic magnetic field sensors, optical fiber vibration sensor, fiber-optic high temperature pressure sensors, fiber-optic WIM system , fiber optic strain gauge welding, fiber optic embedded strain gauge, optical soil pressure gauge, fiber reinforcement meter, fiber optic pressure ring, fiber-optic displacement meter, fiber cracks meter, fiber optic osmometer, fiber-optic temperature sensor high temperature , optical fiber cable meter and so on.

北京达卡科技有限公司光纤方面提供：光纤分布式应力温度测试系统、光纤分布式温度测试系统、光纤光栅健康监测系统、光纤地震检波系统、光纤光栅波长校验仪等，其中传感器产品线极为丰富和具有行业代表性，包括：光纤温湿度计、光纤瓦斯报警器、光纤磁场传感器、光纤振动传感器、光纤耐高温高压传感器、光纤动态称重系统、光纤焊接式应变计、光纤埋入式应变计、光纤土压力计、光纤钢筋计、光纤压力环、光纤位移计、光纤裂缝计、光纤渗压计、光纤耐高温温度传感器、光纤钢索计等。

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。