凸轮轴

Multi-cylinder engines are normally equipped with pumps in unit monobloc form incorporating a corresponding number of elements,having a common camshaft and control means but provided with individual adjustments for regulating their output and setting their timing .

多汽缸发动机一般情况下装配整体式油泵，把相关的喷射单元组合成一体，共用凸轮轴和控制方式，但可单独调整以调节各自功率输出和设定各自的正时。每个喷射单元必须输送等量燃油，按照预定的输送比率分别校准。

The moonlike cylinder head and camshaft hole which is made by single forming reduce the noise caused by the cylinder head.

整体式缸头，凸轮轴孔一次成形，缸头噪声更小。

This engine benefits from variable valve A high-performance chassis for saloon-style driving sensations timing and camshaft variator which permits two types of use: one calibration for idling or when running partially loaded at mid and high revs for maximum power, and a second calibration which permits a bigger overlap between the intake and exhaust strokes for a torque gain of between 5 and 10Nm.

从可变气门的高底盘的轿车性能风格的驾驶感觉，时间和凸轮轴变速器的许可证或空转运行时有部分中的最大功率和高转速装两种用途：1校准这台发动机的好处，和第二个校准它允许更大之间的进排气重叠杆为5至10纳米扭矩增益。

Insert a self-tapping screw into the drilled pin and carefully pull the pin from the camshaft.

插入自动攻丝螺丝到钻孔的销中，小心地在凸轮轴中拉动销。

In addition to its cool camouflaging, a four-stroke, double overhead cam, 499cc engine make this Kymco ATV move like a flash, so if you blink, you'll miss it!

除了它的冷静伪装，四冲程，双凸轮轴， 499cc引擎，使这个kymco亚视提出想要一个闪光灯，因此，如果您一眨眼，你就会错过它！

As well as the Double Vanos variable camshaft system, which allows large amounts of torque to be delivered even at low revs

同时双凸轮轴可变气门正时系统也可以允许发动机在很低的转速下输出巨大的扭矩。

Oil filter, equipped in ubrication system, is mainly in charge of filtering the detrimental impurity in engine oil from oil pan so that the engine oil supplied to bent axle, connecting bar, camshaft and piston ring will be clean and the service life of those parts can be extended.

机油滤清器位于发动机润滑系统中。其作用是对来自油底壳的机油中有害杂质进行滤除，保证供给曲轴、连杆、凸轮轴、增压器、活塞环的机油的清洁，起到润滑、冷却、清洗作用从而延长这些零部件的寿命。

The 4.0-liter V-6 is a single overhead camshaft, 24-valve engine that utilizes a semi-permanent mold cast aluminum block with iron liners and cast aluminum cylinder heads.

4.0升V - 6是一个单顶置凸轮轴，24气门发动机，采用了半永久模铸造铁衬里和铸铝缸盖铝块。

EQ6100 hole in accordance with the crankshaft and camshaft cylinder hole processing demands, first of all, boring head to determine the movement and power parameters; and then the design principle of the completion of program analysis and design of structural calculations; finalized to the motion control system into the design.

摘 要：根据 EQ6100缸体曲轴孔与凸轮轴孔的加工要求，首先确定镗削动力头的运动和动力参数；然后完成方案原理的设计分析以及结构计算设计；最后完成进给运动控制系统的设计。

At present, we are able to provide such motorcycle parts as chain wheel, chain, brake shoe, clutch cover, ignitor, rectifier, relay, high pressure bag, magnetic motor coil, belt, shock absorber, moulding, air valve, valve guide, camshaft, timing chain, spark plug, rocker arm, piston, piston ring, start disc, bearing, oil tank cover, lock set, steering bearing, oil meter, filter, horn, drive plate, driven wheel assembly, buffer rubber, intermediate shaft sleeve, starter motor, spoke and switch button etc.

目前，本公司有以下多个摩托车系列：链轮、链条、制动蹄、离合器压盘点火器、整流器、继电器、高压包、磁电机线圈、皮带、减震器、压条、气门、导管、凸轮轴、时规链、火花塞、摇臂、活塞、活塞环、启动盘、轴承、油箱盖、套锁、转向轴承、油量计、滤清器喇叭、驱动盘、从动轮总成、缓冲胶、中轴套、启动电机、辐条、开关按纽等。

What are your goals and strategies for growth?

你的成长目标和策略是什么？

And unto the angel of the church in Sardis write; These things saith he that hath the seven irits of God, and the seven star I know thy works, that thou hast a name that thou livest, and art dead.

3：1 你要写信给撒狄教会的使者，说，那有神的七灵和七星的，说，我知道你的行为，按名你是活的，其实是死的。