凸轮机构

Facing some difficult design which exists in the cam contour curve of indexing motion mechanism against domestic company presently,the conjugate contour curve was viewed as the idea of design and the motion animation was used as the method of design.

针对目前国内企业在间歇运动机构凸轮轮廓曲线设计中所遇到的困难，采用共轭曲线的设计思想和运动模拟仿真的设计思路，并通过案例，介绍了凸轮轮廓曲线的设计方法。

For example, to counter the disadvantage of apprising the dynamic characteristics of valve train with the maximum negative acceleration which is not enough be observed directly and not enough correct, a method of observing directly the valve trains bounce has been also put forward in this paper.

也就是在理论研究手段基本完备的情况下，利用模型直接观察机构的飞脱现象。并且以6110柴油机配气机构为例，考察了机构中最容易反映飞脱特性的推杆力随结构参数、凸轮型线和凸轮转速的变化规律，为研究配气机构飞脱特性提供了直观有效的方法。

In a disk device, a base body (10) has a drawing lever (80) for inserting a disk, a discharge lever (100) for discharging the disk, and a slider mechanism for pivoting the drawing lever (80) and the discharge lever (100). The slider mechanism has a first cam groove for sliding a first pin of the drawing lever (80) and a second cam groove for sliding a second pin of the discharge lever (100). The drawing lever (80) pivots when the first pin slides in the first cam groove as the slider mechanism operates, and the discharge lever (100) pivots when the second pin slides in the second cam groove as the slider mechanism operates.

该光盘装置，在基座本体(10)上设置插入光盘的引入杆(80)、排出光盘的排出杆(100)以及使引入杆(80)和排出杆(100)转动的滑动机构；在滑动机构上具有使引入杆(80)的第一销滑动的第一凸轮槽和使排出杆(100)的第二销滑动的第二凸轮槽；通过第一销随着滑动机构的动作在第一凸轮槽内滑动，引入杆(80)进行转动，通过第二销随着滑动机构的动作在第二凸轮槽内滑动，排出杆(100)进行转动。

Reducing gear drives cam rotate to top half-turn and link gear of upper gate move, top disc opens and discharges. Spring device makes disc close and replace with displacement of cam. When cam rotates to bottom half-turn link, gear of sub-layer gate moves, below disc opens and discharges. The disc closes little by little with the displacement of cam. These two actions maintain a closed state of either disc on the pipe. So it can discharges and lock air at the same time.?

减速装置带动凸轮旋转至上半圈时，上层阀门的连杆机构互动，阀板逐渐打开卸灰，随着凸轮的旋转，弹簧机构使阀板逐渐关闭复位；凸轮旋转至下半圈时，下层阀门的连杆机构互动，阀板逐渐打开卸灰，随着凸轮的旋转又使阀板逐渐关闭，这样两个动作使管道上阀板始终有一个是关闭状态，因而，可使卸灰与锁气同时达到目的。

Design of eccentric rotating conjugate cams paper-transferring mechanism ;2. On the basis of the principle of TYM 750 Die Cutting and Foilstamping Press,the mathematical model for the paper-transferring mechanism was constructed.

根据TYM 750烫印模切机递纸机构的工作原理，构建递纸机构的数学分析模型，按照递纸吸嘴的运动轨迹，求出递纸机构中凸轮从动杆的运动规律，利用反转法得到凸轮的廓线。

Several essential problems about the mechanism, such as the relations between cam angles and geometric parameters, the allowable values of some angular parameters, the equations of cam prole and the return motion of rocker AC, are solved.

关于这种机构的几个基本问题得到解决，如凸轮角度和几何参数的关系，一些角参数的允许值，凸轮的轮廓线和摇杆的回行运动的方程。

Using ratch cam intermittence shut-off mechanism,keeped parts on a carrier,and shut off after punching a certain length,through the concrete example,the structure principle,working process and design points of the ratch cam intermittence shut-off mechanism were introduced.

应用棘轮凸轮间歇切断机构，将制件留在一条载体上，构成一定长度后再切断成条状，通过具体实例，从棘轮凸轮间歇切断机构结构原理、动作过程、设计要点等方面作了介绍。

After simulation and optimum design, the most proper cam curve of latching mechanism is obtained.

文章提出了凸轮曲线式卡槽机构的两种设计思路，制定了三种卡槽机构的初步设计方案，并对这三种不同的卡槽机构进行了仿真，发现了初步设计方案中存在的一些问题，最后在此基础上进行了优化改进，寻找到凸轮曲线式卡槽的最佳设计方案。

Initially, assuming that the contact between cam and tappet is"dry contart", a dynamics model of Hertzin contact stiffness and impact damping is established. Next, with dynamic load on cam—tappet pair from the model, an analysis is made both to unsteady EHD oil film in cam—tappet pair under condition of full and partial lubrtication and to wear characteristics of cam profile. then, according to the fact that the lubrication in cam—tappet contact surface is EHD lubrication, taking the interaction between stiffness and damping of unsteady EHD oil film and rigidity of solid object contact into account, a dynamics equation of valve train relating to the dynamic effect of EHD oil film is built up and solved. Consequently, a further study is made on the dynamic characteristics of valve train under interaction of EHD oil film dynamic behavior and the problem of EHD lubrication in cam—tappet pair. Finally, the dynamic effect of full and partial EHD oil film is studied accordingly.

首先，通过对凸轮—挺杆接触为&干接触&的假设，建立了考虑赫兹&接触刚度&和冲击&阻尼&的配气机构动力学模型，用由此求得的凸轮—挺杆表面动载荷对凸轮—挺杆进行了全膜状态和部分膜状态非稳态弹流润滑分析，并研究了凸轮轮廓的磨损规律；然后，是在凸轮挺杆表面存在弹流动压油膜这一事实的基础上，相当于在动力学方程中考虑非稳态弹流油膜的&刚度&、&阻尼&和固体接触&刚度&的耦合作用，建立并求解了考虑弹流润滑行为动力学效应的配气机构的动力学方程，从而深入地研究了弹流润滑行为与动力学行为耦合作用下的配气机构动力学特征以及凸轮挺杆弹流润滑问题；作为前面工作的对应部分，考虑弹流油膜动力学效应的研究工作也同样分为全膜状态和部分膜状态进行。

The method can be used to analysis the errors of the parallel indexing cam mech...

本文还对平行分度凸轮机构进行了实例分析计算，论证其正确性。

What are your goals and strategies for growth?

你的成长目标和策略是什么？

And unto the angel of the church in Sardis write; These things saith he that hath the seven irits of God, and the seven star I know thy works, that thou hast a name that thou livest, and art dead.

3：1 你要写信给撒狄教会的使者，说，那有神的七灵和七星的，说，我知道你的行为，按名你是活的，其实是死的。