倾轴的

By using solidworks software,The models of AOD converter shell and molten steel for obtaining the areal coordinates are created to make refined calculation about the tilting moment s of the new or old converters.

运用solidworks软件建立AOD炉及钢液的三维实体模型，以获取其重心坐标，并对新炉、旧炉倾动力矩进行了精确的计算，依据倾动力矩变化曲线提出了防止炉体自动倾翻的耳轴中心安全高度的合理位置。

This axis may be horizontal or it may slant or plunge .

这条轴可能是水平的，也可能是倾伏的。

Took the different diameters double-row bearing slewing ring asexample, this dissertation studied the distribution of axial press ofthe rolling body under axial load and throw moment, the contact pressbetween two outer seat-rings which are connected to the main machinewith high strength screw bolts.

本文以双排异径球式回转支承为例，对球式回转支承在承受轴向载荷和倾翻力矩时的滚动体轴向正压力大小、分布及由高强度螺栓与主机连接的滚圈接触面的接触力进行了详细的理论推导和实际计算，说明在双排球式回转支承的结构静力分析过程中，可以将滚圈安装接触面的接触力简化为铅垂方向的均布载荷。

The device comprises: a conveyer belt; a let-off roller (16) on which the conveyer belt runs and from which the rubber tape is let off; a traverser (21) to move the let-off roller (16) in an X-axis direction parallel to the rotational axis of the object; a radial shifter to move the let-off roller in a Y-axis direction perpendicular to the X-axis direction; a tilter (23) to turn the rotational axis of the let-off roller (16) around a reference axis which is parallel to a Z-axis direction perpendicular to the X-axis direction and Y-axis direction.

所述装置包括：输送带；送出辊，所述输送带在送出辊上行进并且所述橡胶带从送出辊送出；移动台，其沿平行于物体的旋转轴线的X轴方向移动送出辊；径向移位装置，其沿垂直于X轴方向的Y轴方向移动送出辊；倾转装置，用于绕平行于Z轴方向的基准轴线转动送出辊的旋转轴线，所述Z轴方向垂直于X轴方向和Y轴方向。

Upper central incisors moved forward and downward together with maxillary, at the same time they upright in the sagittal plane and tip mesially. 3 The occlusion plane rotated clockwise for about 1.5°. 4 The width increasement effect of RME comes from approximately the equal amounts of skeletal and dental expansion. The mode of dental movement was a combination of body and tipping movements of posterior teeth.

结果：1后牙在宽度方向上为整体移动和倾斜移动相结合的移动方式，但第一磨牙和第一双尖牙稍有差别；牙齿和骨对宽度增加的贡献各占约1/2；2后牙在垂直方向有伸长的趋势；3第一磨牙和第一双尖牙均向前整体移动，轴倾度保持不变；4中切牙整体随上颌骨前部向前向下移动，其牙长轴发生直立，轴倾度增加；5上颌平面发生顺时针旋转。

Orebodies occur in a fault near the axial region in the southern limb of the Jinjinghe-Hujiamiao inverted secondary anticline in the southern limb of the Hongyansi-Heishan composite syncline. Host rocks are dolomitic rocks in the middle and upper parts of the Devonian Qingshiya Formation. Their spatial distribution is obviously controlled by an interlayer fracture-fissure zone near the axial region in the steeply dipping southern limb of an anticline. Ores are dominantly of nodular and stockwork types and the feature of epigenetic mineralization is very pronounced.

矿体产于红岩寺—黑山复式向斜南翼金井河—胡家沟次级背斜南翼近轴部断裂中，赋矿岩石为泥盆系青石垭组中上部白云质岩，其空间展布明显受背斜陡倾南翼近轴部的层间断裂-裂隙带构造控制，矿石主要有团块状和网脉状，其后生成矿现象非常明显。

According to the structural feature of modern tilting levels, the method of erecting the collimation axis to the standing axis and the principle of the setting out of slope with the tilting standing axis are expounded.

根据现代微倾水准仪的视准轴可以调整的构造特点，阐述了使水准仪视准轴垂直于竖轴的方法，以及倾斜竖轴法放样斜坡面的原理；讨论了其误差来源、大小；对照几个行业的设计、施工及验收规范和测量规范，给出了简便可行的操作方法与有效检验手段。

Methods The sample consisted of 2 groups. The subjects in the first group (n = 30) had complete normal dentitions including third molars; those in the second group (n =30) had impacted right and left third molars.

研究样本分为两组，第一组的研究目的确定上颌第三磨牙萌出与第一磨牙和第二磨牙轴倾度的关系。

There are six major parameters impacting vehicle handling and stability performance: the cg location, the rigidity of tyre side list, the rigidity of steering system, the steering system transmission ratio, the rear axle roll steering coefficient and the entire vehicle circling the vertical axis the rotating inertia.

对操稳性影响较大的主要有6个参数：重心位置、车轮侧偏刚度、转向系刚度、转向系传动比、后轴侧倾转向系数及整车绕垂直轴的转动惯量。

Nonlinear partial differential dynamic equations of bending vibration of a tilting stepped drive shaft with two supports were built under non-inertia movement coordinate system by theorem of the motion of mass center and Heaviside function. According to the condition of equal displacement in an adjoining plane of the shaft, an equivalent shaft and its equation were obtained. A motion equation of the equivalent shaft was obtained by method of Galerkin. An approximate steady-state solution of the main resonance was obtained by method of multiple scales. The influence factors, motion stability, amplitude jump of main resonance of a stepped drive shaft and so on were analyzed.

用质心运动定理、Heaviside函数建立了非惯性系下倾料两端支承阶梯传动轴的非线性弯曲振动偏微分动力学方程，并根据相邻轴段的衔接面处位移相等的条件，得到阶梯轴的当量轴及其动力学方程；用Galerkin法得到当量轴的弯曲运动方程，用多尺度法求得稳态下当量轴的主共振的一次近似定常解，分析了影响阶梯传动轴主共振的因素、运动稳定性、振幅突变性等。

Means the parent directory, so this command means to execute "toolchain.sh," which is in the current directory.

代表父目录，所以这个命令就是执行当前目录下的"toolchain.sh"。

Yes,In fact,I'm on our city ream.

是的。事实上我是我们市队的。