仪表读数

The pressure system consists of socket, bourdon tube and transfer mechanism and show the value through the pointer.

仪表的测量系统由接头、弹簧管和传动机构组成。通过指针指示仪表读数。

After each addition, wait until a constant potential has been established and record the burette

在每次加量后。等到稳定的电压后记下量管的读数及仪表读数。

The electronic heating evaporator in the high-side gravity recirculation system in ANSI/ASHRAE 64-2500 standard is replaced by a new type plate evaporator which is more effcient and energy-saving, because the cold water outlet from the evaporator that is used to heat the cryogen can be used once again to cool the air in the air inlet trunk; an air processing unit is designed in the lab design, so to imitate all kinds of weather in each season in every location of China at any time the test is being made; the data selection system can send all the data in the test to the computer at one time, and to reduce the cost of the test some data which is more stable are read manually through traditional meters if this can not sacrifice the precision of the test.

本文的设计中用效率更高的新型板式换热器代替了原ANSFASHRAE 64——2500标准中压缩驱动循环系统中的电加热蒸发器，加热冷剂后得到的低温淡水还可以用于冷却进气通道中的空气，不仅提高了效率，而且更加节能；实验室方案中增加了空气处理系统，可以实现随时对全国各地各季节的空气状态进行模拟，方便实验的进行；采用数据采集系统将数据整体采集到电脑中方便数据处理，而且对于变化频率不高相对较为稳定的数据采取传统仪表进行人工读数，在保证测试结果准确性的前提下降低了成本。

Note all the readings in the instrument board after the engine starts, more attention to L.

起动后应密切注意仪表板各仪表读数，尤其是机油压力，如没有压力，应立即停车检查。

Historically, I've shown "live" Instrument readings through the constant updating of a numerical value by using constant value array.

从历史上看，我已经展示"活"的仪表读数，通过不断的更新数值使用常量数组。

Construct a graph by plotting the meter readings versus the volumes of standard silver nitrate solution used in the titration.

通过仪表读数及与之读数相对应的在测式中所用销酸银溶液的量建立一个图表。

Presently, the reading work of the dial indicator in our country still adopts the manual method. This method is restricted by such subjective factors as observing angel and distance as well as fatigue strength and so on, which results in not only large error and low reliability but also low efficiency and great labor costs.

目前国内对这类仪表的判读工作主要是采用人工观测仪表表盘指针来读数的方法，这种方法受人的主观因素如人的观测角度、观测距离及疲劳强度等的影响，误差较大，可靠性不高，且工作效率低，劳动强度大。

Zero/calibrate the gauge, set the gauge reading to a specified point according to test spec normally 7bar

清零/标定该仪表，根据测试规范设置仪表读数到指定读数上通常为7bar

The experiments, in the case of using compass, show that the system has both good effectiveness on processing of image of gauge and high precision on recognizing readings. So the system is applicable for the situation that is inconvenient to get the parameters directly.

通过以两种型号的罗经为例进行实验表明，该系统对仪表图像的处理效果较好，识别的读数结果精度较高，对于不便于直接读数的场合具有较强的适用性。

Lowly open vent needle valve until gauge reads 1.0 PSID then close vent needle valve holding pressure at 1.0 PSID.

tep 7 慢慢开启排气针形阀，直到仪表读数达到1.0 PSID为止，然后关闭排气针形阀，保持压力在1.0 PSID。

If you are unfortunate enough to the lovelorn, please tell me, I will help you out, really, please contact me!

如果你不幸失恋了，请告诉我，我会帮助你摆脱困境，真的，请联系我啦！

China's plan to cut energy intensity by 20 percent and pollutant discharges by 10 percent between 2006 and 2010 is a case in point.

中国计划在2006年到2010间降低20%的能源强度和减少10%的主要污染物排放，就是一个这样的例子。