查询词典 welds

Where the difference in thickness between the abutting member and the table member is considerable, the size of fillet welds will be specially considered.

例 1：当角接的两个构件的厚度相差甚大时，则该角焊缝的尺寸将予以特殊考虑。

The analysis and test results show that the concentration of stresses at the end of fillet welds between the tensile anchor plate and the tensile anchor tube is obvious, and the maximum principal tensile stress occurs in the stress concentration region.

结果表明，锚拉板与锚拉筒之间的连接焊缝下端部应力集中明显，最大主拉应力出现在该区域；在设计疲劳荷载作用下，该结构关键构造细节处均未发现疲劳裂纹，结构疲劳性能满足设计要求。

Die bonder is a kind of microelectronics encapsulation device that welds transistors to the base. Temperature control system is one important part of it.

粘片机是一种将晶源焊接到底座的微电子封装设备，温度控制系统是其较为重要的组成部分。

The butt weld is easier to inspect nondestructively than the fillet welds.

对接焊缝比角接焊缝更容易进行无破坏检查。

He may give the Screw Machine a pair of lobsterlike pincers instead of a buzz saw, or he welds a flamethrower to one arm of 25-foot-tall Big Totem.

他可能换掉"螺丝锥"的电锯，代之以龙虾似的一对大铁螯，也可能给25英尺身高的"大坨塔"的胳膊焊上一把喷火枪。

Frames that are welded should have beautiful thick welds that you'd want to eat off them.

应该是有美丽的焊接焊缝厚，你会希望把他们吃的框架。

After a few test welds with it the firebox was welded together.

经过几次试验焊缝与它的Firebox是焊接在一起。

Creep tests of P91 base material and its welds have been carried out,the creep behavior of P91 studied and creep rupture strength extrapolated by the Isothermal and the L-M parameter methods,followed by creep life estimations of P91 fresh steam pipes.

对P91钢母材和焊接接头进行持久试验，研究P91钢的蠕变特性，采用等温线法和L-M参数法对持久强度进行外推，进而对P91钢制主蒸汽管道的蠕变寿命进行估算。

Transfers the bottom type resistance furnace structure outer covering becomes by the steel plate and the section welding, the furnace body welds the system full circle densely by the steel plate, lower part the spatial installment has the turntable support, the kingbolt, on the furnace body foot ledgerwall the installment has the velocity modulation electrical machinery and the transmission gearbox, through the umbrella type gear and the main axle connection, transfers the bottom type resistance furnace's stove village material to use fan-shaped ultra light quality high strength 0.6g/cm3 to conserveenergy the fireproof heat preservation brick, the heat insulating layer uses the aluminum silicate textile fiber felt and the inflation heat preservation powder, the resistance silk thread becomes spiral-shaped, installs according to the average temperature rule in the resistance wire trough, the basealso arranges the resistance wire in the special-purpose trough, in such stove the temperature is even, the work piece and the turntable cannot bump with the resistance wire, resistance wireThe service life is long, is not easy to damage.

转底式电阻炉结构外壳由钢板和型钢焊接而成，炉体由钢板密焊制成圆型，下部空间安装有转盘支撑，旋转主轴，炉体最下部底板上安装有调速电机和变速器，通过伞型齿轮与主轴连接，转底式电阻炉的炉村材料采用扇形超轻质高强度0.6g/cm3节能耐火保温砖，保温层采用硅酸铝纤维毡和膨胀保温粉，电阻丝线成螺旋状，按均温规律安装在电阻丝槽内，底部也布置电阻丝在专用槽内，这样炉内温度均匀，工件及转盘不会与电阻丝相碰，电阻丝使用寿命长，不易损坏。

Transfers the bottom type resistance furnace structure outer covering becomes by the steel plate and the section welding, the furnace body welds the system full circle densely by the steel plate, lower part the spatial installment has the turntable support, the kingbolt, on the furnace body foot ledger wall the installment has the velocity modulation electrical machinery and the transmission gearbox, through the umbrella type gear and the main axle connection, transfers the bottom type resistance furnace's stove village material to use fan-shaped ultra light quality high strength 0.6g/cm3 to conserve energy the fireproof heat preservation brick, the heat insulating layer uses the aluminum silicate textile fiber felt and the inflation heat preservation powder, the resistance silk thread becomes spiral-shaped, installs according to the average temperature rule in the resistance wire trough, the base also arranges the resistance wire in the special-purpose trough, in such stove the temperature is even, the work piece and the turntable cannot bump with the resistance wire, resistance wireThe service life is long, is not easy to damage.

转底式电阻炉结构外壳由钢板和型钢焊接而成，炉体由钢板密焊制成圆型，下部空间安装有转盘支撑，旋转主轴，炉体最下部底板上安装有调速电机和变速器，通过伞型齿轮与主轴连接，转底式电阻炉的炉村材料采用扇形超轻质高强度0.6g/cm3节能耐火保温砖，保温层采用硅酸铝纤维毡和膨胀保温粉，电阻丝线成螺旋状，按均温规律安装在电阻丝槽内，底部也布置电阻丝在专用槽内，这样炉内温度均匀，工件及转盘不会与电阻丝相碰，电阻丝使用寿命长，不易损坏。

If you are unfortunate enough to the lovelorn, please tell me, I will help you out, really, please contact me!

如果你不幸失恋了，请告诉我，我会帮助你摆脱困境，真的，请联系我啦！

China's plan to cut energy intensity by 20 percent and pollutant discharges by 10 percent between 2006 and 2010 is a case in point.

中国计划在2006年到2010间降低20%的能源强度和减少10%的主要污染物排放，就是一个这样的例子。