查询词典 watchdog

The 4B Watchdog "Elite" uses non-contacting, magnetic sensors to monitor belt speed and belt alignment at the head / boot or both. Additional sensors monitor bearing temperature, head pulley alignment and plugged spout conditions.

4B Watchdog "Elite"运用非接触，磁性传感器监控带速和头部/尾部或两者传送带调整，附加的传感器监控轴承温度，主动皮带轮调整＆插入喷管的状况。

Four 8-bit I/O Ports C Three 16-bit Timer/Counters C 256 Bytes Scratch Pad RAM C 8 Interrupt Sources with 4 Priority Levels C Dual Data Pointer Variable Length MOVX for Slow RAM/Peripherals High-speed Architecture C 10 to 40 MHz in Standard Mode 16K/32K Bytes On-Chip ROM Program T80C51RD2 ROMless Versions On-Chip 1024 bytes Expanded RAM C Software Selectable Size (0, 256, 512, 768, 1024 bytes) C 256 Bytes Selected at Reset for AT87C51RB2/RC2 Compatibility Keyboard Interrupt Interface on Port P1 8-bit Clock Prescaler 64K Program and Data Memory Spaces Improved X2 Mode with Independant Selection for CPU and Each Peripheral Programmable Counter Array 5 Channels with: C High-speed Output C Compare/Capture C Pulse Width Modulator C Watchdog Timer Capabilities Asynchronous Port Reset Full Duplex Enhanced UART Dedicated Baud Rate Generator for UART Low EMI Hardware Watchdog Timer (One-time Enabled with Reset-out) Power Control Modes C Idle Mode C Power-down Mode C Power-off Flag Power Supply: 2.7V to 5.5V or 2.7V to 3.6V Temperature Ranges: Commercial (0 to +70C) and Industrial (-40C to +85C) Packages: PDIL40, PLCC44, VQFP44

四8位I / O端口C款三16位定时器/计数器 256字节RAM的便笺簿 8中断源4优先级和C双数据指针MOVX在缓变长内存/外设高速架构为C 10至40 MHz的标准模式16K/32K字节的片上ROM程序T80C51RD2无ROM版本片1024字节扩展RAMC软件可选尺寸（0，256， 512，768，1024字节）C选取在重置为AT87C51RB2/RC2兼容键盘中断接口与独立的选择港口小一8位时钟分频器64K的程序和数据存储器空间的改进X2模式的CPU和256字节每个外设可编程计数器5通道的阵列：C型高速输出C比较/脉宽调制器捕获看门狗定时器复位功能异步端口全双工增强型UART的波特率发生器的UART低EMI硬件看门狗定时器电源控制模式空闲模式C掉电模式C断电旗电源：2.7V至5.5V或2.7V至3.6V温度范围：商业（0到+70 C）和工业（- 40C至+85℃）封装：PDIL40，PLCC44，VQFP44

The system adopts CPU board with fast processing elevator operational program, data signal exchange, and HMI screen, which can make sure reliable operation and high speed. It also has PHILIPS SJA1000T field CAN bus, 82C251 Bus interface and the latest serial storage technique to record data. The functions of external watchdog and control chip internal watchdog compose two-level procedure monitoring, so as to ensure the normal operation of the control program. Heavy-current switch power LM2576 ensures the stable system working power, which has low requirements for the power supply. High-speed optoelectronic isolator and internal frequency division technology can make NW3P08-41C (42C) CPU receive the input impulse up to 1-phase 100 KHZ*2 CHANEL or 2-phase 50KHZ*1 CHANEL 32bit.

系统采用原装中央处理板，具有快速的处理电梯运行程序、数据信号交换、显示屏人机界面；确保可靠运行电梯控制程序；且速度快，PHILIPS 公司 SJA1000T 现场 CAN 总线；以及 82C251BUS 接口，最新串行存贮技术记录数据；外部看门狗及控制芯片内部看门狗功能组成两级程序监视，确保控制程序正常运行；大电流开关电源 LM2576 确保系统工作电源稳定，且对供电电源要求低；高速光电隔离光藕及微机内部分频技术，使 NW3P08-41C(42C)中央处理板可接收高达 1 相 100KHZ*2通道或 2 相 50KHZ*1通道，32bit 的计数脉冲。

The method comprises the following steps of: starting the watchdog; counting from 0, the watchdog detects that the system reads the counting value; calculating the remainder after the counting value is divided by a pre-arranged value; re-counting from the remainder by the watchdog.

方法包括：看门狗启动，从0开始计数，看门狗检测到系统读取计数值，计算计数值除以预设值后所得的余数，看门狗从该余数起重新开始计数。

A use a watchdog or other monitoring entity to deterministically kill threads.

能够用watchdog或其他监控工具来坚决的结束线程。

Use a watchdog or other monitoring entity to deterministically kill threads.

使用Watchdog或其它的监控工具来确保终止线程。

A use a watchdog or other monitoring entity to deterministically kill threads.

能用watchdog或其他监视工具来坚决的结束线程。

A Use a watchdog or other monitoring ent IT y to deterministically kill threads.

可以用watchdog或其他监控工具来坚决的结束线程。

A Use a watchdog or other monitoring entity to deterministically kill threads.

可以用watchdog或其他监控工具来坚决的结束线程。

A Use a watchdog or other monitoring entity to deterministically kill threads.

可以用watchdog或其他****工具来坚决的结束线程。

Graf, without question, is the greatest women's player in history.

格拉芙，现在，毫无疑问是女子网坛历史上最伟大的选手。

If not, you will have to look around at all your important data.

如果没有，您将需要检查所有的重要数据。