查询词典 van load

Third, based on the example of over proof on-load loss in 180MVA/220kV power transformer, the eddy loss in winding is analyzed with the leakage flux element software. Some conclusions with practical use are given. In order to reduce the load loss, primarily we should reduce radial leakage flux of transformer possibily.

运用漏磁场分析软件，以180MVA/220kV电力变压器负载损耗超标为例，进行详细分析，提出有工程实用价值的结论：降低变压器负载损耗，从根本上应尽可能减少变压器辐向漏磁。

This thesis DESign steel wire tension control system of Steel Billet Grinding Machine, and establish mathematical model of every component in electro-hydraulic proportional valve control dissymmetry hydraulic cylinder servosystem and the load with large inertia and flexibility system of Grinding Machine. Through the medium of matlab/simulink simulation, this thesis mostly analyses Pre-load impact of steel wire stress. Compare with the emulation result of non-feedback, force feedback, displacement feedback, thereby educe reliable conclusion.

本文设计了钢坯修磨机钢丝绳张力控制系统，并且对电液比例阀控非对称液压缸伺服系统的所有液压元件和修磨机柔性负载系统进行了建模，通过MATLAB／SIMULINK仿真，主要分析了预紧力对钢丝绳受力的影响，而且对开环无反馈、力环反馈、位移反馈的仿真结果进行了比较、得出了可靠的结论。

The detailed steady state process of OCC APF with both resistive load and nonlinear load is analyzed,based on which the physical meaning and steady condition of proportional part and integral part in PI controller are given.

在此基础上给出了 PI调节器中P和I环节的物理意义及其应满足的条件，发现可将其作用分开：I环节主导Um长期内较大的变动，用来反映负载大小的改变；P环节每个工频周期内对Um小范围调整，用来平衡每个工频周期内负载存在的谐波。

On the single row angular contact bearings, radial load rating of bearing rings relative to each other purely radial displacement of the load of the radial component.

对单列角接触轴承，径向额定负荷为引起轴承套圈彼此相对纯径向位移的负荷的径向分量。

To a module of single output, its load is rated load.

单路输出的变换器，其输出负载就是其额定负载。

In this case the 225/45R17 91W Standard Load size's rated load capacity of 1,477 lbs.

在这种情况下， 225/45R17 91W标准负荷大小的额定负载能力1477英镑。

When is tested,testing shall be performed with rated load current of firstly, and then with load current of inverter.

在测试时（仅限 Power 测试），的额定负载电流，后带的负载电流。

Traditionally,the vehicle overload is defined as the load that exceeds its rated load.

传统意义上车辆的超载是指车辆当前负荷高于该车型的额定载荷。

At the detecting point of the load signal,the rated three-phase load power is divided in section on real-time.

在负荷信号检测端，采取按三相负荷功率的额度进行实时分段的措施。

As the test shows, when the rated load is 25%, the air leakage volume will be about twice of 100% load.

因此在低负荷启动时，必须抽除更多的空气以保持凝汽器的最低压力。

If you were not , and OS X just booted normally, have no fear.

如果你没有，和OS X刚刚启动通常，没有恐惧。

I only want to preserve our all .

我只想保存好我们的一切