查询词典 trial-and-error method

By applying the concept of "dominant input",the existence of both the approximation error and external disturbance which are supposed to have unknown boundaries is considered.What's more,the adaptive law utilizes two types of errors in the adaptive fuzzy systems,the tracking error and approximation error.

该方法应用"主导输入"的概念，同时考虑了函数逼近误差和系统外扰的存在，假设了该系统逼近误差和系统外扰有界但界未知的情况；并探讨了自适应模糊控制器的参数自适应律由跟踪误差和逼近误差共同进行调节。

Analysis of slewing errors angle is proceeded with measurement error of the drive chain and every effect of errors factor on slewing error is quantitatively analyzed in the paper. And the numeric moel of caculating slewing error angle is established.

本文主要从传动链尺寸误差入手定量分析各项误差因素对FA传动回差的影响，并建立计算回差的数学模型。

The mathematical model between position error and north seeking error is gotten through error theory and partial derivative principle.

运用误差理论和偏导数原理，推导出转位误差与寻北误差二者之间的关系模型。

The maximum error of regional anomaly separation is 3.101×10^(-6)m/s^2 the mean square error is 0.989×10^(-6)m/s^2 and the maximum percentage error is 7.76% for several data on the boundary and is lower than 4.1% for the other points.

分离出的区域异常最大误差为3.101×10^(-6)m/s^2，均方差为0.989×10^(-6)m/s^2，最大百分比误差仅在边部的几个数据上，为7.76%，其余各点的误差均小于4.1%。

The results show that the phase error of the vector measurement is zero, and amplitude error can be eliminated, and the error caused by D/A is much lower than a LBS.

结果证明，相位测量的理论误差为零，幅度测量的理论误差可用修正系数消除，且D/A有限字长引起的误差远小于一个LBS。

As the existence of qualitative calculation error and statistical error, we have to use the qualitative analysis to examine the scientific nature and effectiveness of the work, making sure to reduce the error of qualitative calculation.

由于在定量计算中系统误差和统计误差的存在，为此在定量分析之后，都有相关定性分析加以分析和解验，以求研究工作的科学性和有效性。

Aiming at researching on the theory of the shaft-kind parts form error evaluation and its application, on the basis of the analysis for the geometric model of the roundness error and cylindricity error, the linear programming models of the enclosure evaluation were proposed. According to the features of the proposed models, the solution of the optimization algorithms of linear planning was discussed to obtain accurate evaluation results.

为了对轴类零件形状误差评定理论及应用进行研究，在分析轴类零件的圆度、圆柱度误差评定几何模型的基础上，建立了包容拟合评定的规划数学模型，并针对模型的特点，探讨了使用线形规划的单纯形优化算法进行规划模型的求解，从而获得精确的形状误差评定结果。

Its precision mainly lies on the Abbe Error caused by the offset between the centerline and the mobile line of the capacitive-gate ruler, the heeling error of the guide mechanism, and the error caused by the dilatometric change of parts resulted from the temperature change.

主要在于它的精度造成的阿贝误差之间的中心线与电容栅尺移动线偏移，指南的机制倾斜误差，以及零件的热膨胀变化引起的温度变化导致的错误。

The adaptive compensation term of the optimal approximation error and a new robust term are adopted to minify the influence of modeling error and parameter estimation error.

该方案通过引入最优逼近误差的自适应补偿项和新的鲁棒项，削减建模误差和参数估计误差的影响，从而在稳定性分析中取消了要求逼近误差平方可积或逼近误差的上确界已知的条件。

As the result of theoretical analysis and practical test, the systematic error corrections of the second-order level measurement must include collimation error correction, refraction error correction and orthometric correction (altitude over more than 50 m in the examining area).

经理论分析与实际测试后发现二等水准测量须做视准轴误差、折射误差与正高改正（测区标高超过50公尺以上），而二等水准测量，则须加人视准轴误差，测区标高超过100公尺以上，亦需加人正高改正。

It's not quite as simple as that.

并没有那么容易。

It debuted in 1992 in Japan and the United Kingdom, and 1993 in the United States.

它首次亮相于1992年在日本和英国，在美国1993年。