查询词典 trial-and-error method

The error of ultimate load prediction after retrofitting:the error of structure program and preliminary estimation are between respectively 35~80% and 25~40%, the reason of error results from the slight deformation between the fixed beam relation with brick arch and reaction force base.

砖拱补强后，其水平极限荷载预测之误差：值分析程式预测结果误差约在35~80%之间，推估公式预测结果误差约在25~40%之间，试验进时砖拱与底固定处及底与反基座产生微小变形应为误差源。

Moreover, the accuracy analysis for different measurements and parameters(such as time measure error, azimuth measure error, buoys error, baseline length and sound velocity fluctuation) are given respectively. To make the best use of the observation datas, the weighted least square localization algorithm is used to improve the accuracy in bistatic sonar. The simulation results show that the positioning accuracy of this algorithm is higher than the other four algorithms, with which the positioning accuracy in stations areas and side areas can be improved effectively.

同时，通过对系统各个因素，如系统的各观测量的测量误差、站址误差、基线长度、声速波动等参数对算法性能的影响，得出了各方法定位误差的分布规律；为了充分利用双基地声纳系统的观测数据，提高系统的定位精度，采用加权最小二乘方法对系统的数据进行优化处理，仿真结果表明该方法定位精度明显高于基本方法的定位精度，能有效的改善发射站和接受站侧边区的定位精度，且定位性能受站址测量误差的影响较小。

Then the error sources of the reaction type and electron type electric energy mete were analyzed and the theory analysis result through the concrete test have been proved. At last, the main conclusion has been drawn. When the induction type electric energy meter measures harmonics energy, the negative error characteristic appears. The higher the frequency of harmonics is, the greater the error is. The electron type electric energy meter can measure harmonics energy accurately in general cases. Except thermo-electrical conversion type electron type power meter, reaction type and electron type electric energy meter can measure direct current power.

本论文通过分析感应式和电子式电能表的工作原理推导出了电能表计量电能的数学模型；分析了感应式和电子式电能表的误差来源以及谐波对计量的影响，并通过具体的试验对理论分析结果进行了验证；得出了如下谐波对电能表计量影响的主要结论：感应式电能表计量谐波电能时，呈现负的误差特性，谐波频率越高，误差越大；电子式电能表在其频响范围内可以准确计量谐波电能。

The complexity of bodywork decides variety of it's error. The station and primary factor which cause error is inconstant change and using correlation analysis can find out the primary factor. With an project given, the theory of correlation analysis for dimension variation of bodywork is discussed through correlation analysis and the layer structure of the bodywork,the state in which the error happened can be found out. How to use eigenva...

车体装焊的复杂性决定了误差产生的多因素性，车体制造过程中产生误差的工位和主要因素是不断变化的，采用相关性分析方法从众多的误差根源中准确地发现最主要的误差源；结合工程实践，论述了车体尺寸波动的相关性分析方法的原理，根据测量点的相关性分析和车体焊接工艺的层次结构，可准确地找到产生车体尺寸误差的工位；讨论了如何利用相关系数矩阵的特征值和相应的特征向量判断尺寸波动的模式，指出测量数据的波动主要按最大特征值所对应的特征向量方式波动，引起这种波动的原因是车体误差产生的主要原因，应重点采取措施加以控制；提出了应用计算机进行相关性分析的解决方案。

Simulation results show that in the image rotation and scale variation range resulted from the navigation system error and the measurement error of the wireless pressure altimeter, the proposed image matching algorithm can satisfy the accuracy demands of the scene aided navigation system and provide the location error-correcting information of the system.

仿真分析表明，在导航系统误差漂移所引起的图像旋转和气压高度表所引起的尺度变化范围内，该算法能满足匹配准确性的要求，并能有效给出系统的定位误差修正信息。

And the temperature error could be divided into accidental error and systematic error.

其温度误差分为随机误差和系统误差两部分。

Sampling error or allowable error is conventionally accepted between 1% and 10%; however, it is suggested that sampling error should be carefully assessed in light of the nature of the derivation of the population proportion and other aspects of the initial data.

抽样误差或允许误差是接受常规的1 ％和10 ％，但是，有人建议，抽样误差应当认真评估根据的性质推导的人口比例和其他方面的初步数据。

The average error, maximum error and the error standard deviation regarding the test data decrease by 37%(45%), 34%(40%) and 35%(40%), respectively.

对测试数据的平均误差、最大误差和标准差较传统ANFIS分别下降了37%(45%)， 34%(40%)和35%(40%)。

Based on the criteria of roundness error, the definition of the circumscribed circle and inscribed circle with the least roundness error was given. The solution to the circumscribed circle and inscribed circle with the least roundness error was proposed when they met with the criterion of obtuse triangle.

根据圆度误差评定的判别准则，给出具有最小误差的外接圆和内接圆的定义，并提出了解决具有最小误差的外接圆和内接圆满足钝角三角形准则时的误差评定方法。

Fourthly, this paper standardizes the linear of the inductance sensor and analyzes its error. Then we discuss the angle error of the laser sensor and the datum plane error of the mechanism.

第四， 此外，本文还对电感传感器进行了线性校正及误差分析，讨论了激光传感器倾角误差，并对机械设计中的定位结构进行了误差分析，提出了改进的措施。

It's bell can reach over a meter in diameter.

它的身体最大可以达到直径1米多。

Now they are overdue and I shall have to pay a fine.

现在他们过期了，我不得不付罚款。