查询词典 tolerance factor

Ds Explained the technology of tolerance design;Aimed at Antenna Structure based on modularized assembly, by referring to the random numbers based on Uncertainty Theory that accord with tolerance distribution rule and using Monte Carlo simulation, a simulated analysis and mathematical statistics of the Antenna-Structured Precision Information Model terminal error have been done.

对产品精度信息模型的公差分析和公差综合技术进行说明；针对模块化装配的天线结构产品精度信息模型，基于不确定性理论的随机公差分布，利用蒙特卡洛模拟法来对天线结构的装配产品精度信息模型的终端误差进行仿真分析和综合。

The detailed processing and analysis of the experimental results indicate that the color discrimination characteristics of human eyes are different for individual color regions and directions in the a*-b* plane,and namely the CIE1976 a*-b* plane is visually non-uniform. The visual color tolerance in the third and fourth quadrants is smaller than the first and second quadrants, the biggest tolerance is in the region of high chroma orange, and the smallest is in blue.

通过对实验数据的详细处理和分析表明，等明度a*-b*平面非视觉均匀，人眼对一、二象限的色宽容度普遍高于三、四象限的色宽容度，对高彩度的橙色具有最高的宽容度，对蓝色具有最低的宽容度，所有的颜色在红-绿方向的视觉色差尺度均低于黄-蓝方向。

Based on the idea of tolerance-robustness design,considering the fuzziness of product quality,and taking the ratio of the variance of probability density function of deviation distribution for the close-loop to the probability of high-quality product as design objectives,the objective function of the loss of quality robustness for this tolerance optimization design was established.

在目标函数中，加工成本是优化的一个重要目标，即寻求总加工成本的最小化，同时还要使设计的产品质量稳健性好，即寻求产品质量稳健性损失成本的最小化。

General dimensional tolerance and geometric tolerance stipulated in this standard are applicable to weldment, welding assembly parts, and welded construction.

本标准规定的一般尺寸公差和形位公差适用于焊件、焊接组装件和焊接结构。

This is not simple tolerance, this tolerance, such as whetstone, Sharpen your will, your life edge.

这不是简单的宽容，这宽容如硎，磨砺着你的意志，磨亮了你生命的锋芒。

Chlorophyll contents and xanthophyll cycle pool calculated from reflectance were closely related with cucumber tolerance to salt stress, and reflectance characteristics could be used as index to evaluate cucumber cultivar tolerance to salt stress.

利用光谱反射指标得出的叶绿素含量、叶黄素循环库的大小与黄瓜的盐害程度及不同品种的耐盐程度有密切关系，反射光谱特性可以用来作为筛选黄瓜耐盐的生理指标。

Tolerance zigzagged on the way of history, and the significance of tolerance was exposed in the multi-dimensional comparison of horizontal and longitudinal orientations.

宽容与不宽容同行，在寻求真理的同时怀抱宽容之心何其难也；宽容在历史中曲折前进，宽容意义展示在横向与纵向的多维比较中。

The result showed that the methane tank sludge was execellent, with 25338.16 mL of the total aerogenesis tolerance, 844.61 mL of day aerogenesis tolerance.

通过对沼气池污泥的接种量设置不同的梯度，研究接种量对产气效果的影响。

The results showed that under 8% of raw total solids concentration, 6.8-7.4 of pH, the methane tank sludge, 20% of them inoculated, after 30 days of fermentation, it was 9 days of period that the effect was execellent. The total aerogenesis tolerance was 42490.70 mL, the day aerogenesis tolerance was 1416.36 mL, the pit held aerogenesis rate was 0.217 m~3/m~3·d , the stuff held aerogenesis rate was 0.241 m~3/m~3·d, the raw material aerogenesis rate was 0.090 m~3/kg·TS.

结果表明，在原料的总固体浓度为8％、pH值介于6.8～7.4、接种沼气池污泥量为原料干物质重量的20％、发酵周期为30d时，对发酵系统间隔9d换料的效果最好，其在总产气量、日均产气量、池容产气率、料容产气率和原料产气率分别达到了42490.70mL、1416.36mL、0.217m~3／m~3·d、0.241m~3／m~3·d和0.090m~3／kg·TS，都比不换料的对照处理有很大提高，分别提高了153.41％、153.41％、152.33％、153.68％和150％，沼气中的甲烷含量也在70％以上。

TJU103 combined with CTLA4-Ig could induce tolerance of donor CD4〓 T-cell to the given antigen, and the tolerance could be transferred by the anergic CD4〓 T-cell and supernatants.

TJU103联合CTLA4-Ig应用，能够调节Th细胞分化，诱导Th细胞发生免疫偏离，使辅助性T细胞更多地向Th2细胞方向分化，有利于免疫耐受的形成。

Cable dampener cannot be rolled up but must be hung over the cable.

缆帆不能被卷起，必须保证处于展开状态

"This skylark is a present from my master," he says.

"这只云雀是我主人献上的礼物。"他说。