查询词典 thread bar

First two are obvious, working thread waits for a message to be posted into input queue and then processes it and service thread could break connection on inactivity timeout or could be used for performing idle periodic tasks.

前两个很明显，工作线程等候发送到队列中的消息并处理它，服务线程可以在连接超时后中断连接，也可以用于执行空闲任务。

The main products are polyester sewing thread, artificial silk embroidery threads, singeing mercerized cotton yarn, cotton packets Di, Di Di packages such as sewing thread.

主要产品有涤纶缝纫线，人造丝绣花线、纯棉丝光烧毛纱线、棉包涤、涤包涤缝纫线等。

Other major products are polyester sewing thread, artificial silk embroidery threads, singeing mercerized cotton yarn, cotton packets Di, Di Di packages such as sewing thread, with an annual output of nearly 10,000 tons of polyester, rayon embroidery threads nearly 1,000 tons.

其他主要产品有涤纶缝纫线，人造丝绣花线、纯棉丝光烧毛纱线、棉包涤、涤包涤缝纫线等，年产涤纶线近万吨，人造丝绣花线近千吨。

Moreover, elasticity and potency should be moderate during embroidering.meantime don't tie a knot in the begining of stitching and the ending and the head of thread lefting one cm should be pressed firmly on the back of material and pay attention to avoid the sleave of the head of the thread.

绣出的方向要一致，起针时应确定中心点，绣时要松紧适度用力均匀，起针或结束时不要打结，应留出一厘米左右的线头在面料背面相互压牢，注意不要使线头纠缠成团。

GO and NOT GO Plain Ring and Snap Gages for Checking Major Diameter of Product External Thread: The GO gage must completely receive or pass over the major diameter of the product external thread to ensure that the major diameter does not exceed the maximummaterial-limit.

用于检查产品外螺纹大径的通规与止规普通环规及卡规：这个通规必须完全配合或经过产品外螺纹大径来确保大径不会超过最大实体极限。

Because the horizontal lathe craft scope is quite widespread, may in the turning the outer annulus cylinder, the circular conical surface, the ring channel, the solid of revolution formation surface, the turning end surface and each kind of commonly used metric system, the British system, the mold notational system, the pitch system thread, but also may carry on drills the center bore, the drill hole, the broaching, reams, work and so on tapping, wrap thread and knurling.

因为卧式车床的工艺范围相当广泛，可以车削内外圆柱面、圆锥面、环形槽、回转体成型面，车削端面和各种常用的公制、英制、模数制、径节制螺纹，还可以进行钻中心孔、钻孔、扩孔、铰孔、攻螺纹、套螺纹和滚花等工作。

A thread state variable corresponding to the dependency is used to indicate that the thread is in inactive mode.

与该相关性相对应的线程状态变量被用于指示该线程处于不活动模式。

A piece of thread was tightly wrapped around the middle of a "mother" and knotted in such a way that there was thread on top and on bottom of the zooglea submersed in the tea.

丝片紧固缠绕在"母体"中间和在茶中浸没的菌胶团的顶部和底部有细丝交结，。

Most importantly, he emphasized the presence of lines. Anekawa Taku believes that although we use thread in our daily life, we did not fully express the appeal of thread.

很多人都把姉川たく误认为刺绣艺术家，但是使用线条只是他艺术创作上的一个工具他作品，以丝质背景与刺绣方法结合，营造三次元世界的拼贴感，重点在於强调线条的存在姉川たく认为虽然我们日常生活中使用线，但多数人并没有把线的魅力充分的表现出来。

With the rapid development of our market economy , the require of taper thread is more and more and the demand of the taper thread precision is higher and higher both at home and abroad.

随着我国市场经济的发展，国内外市场对锥螺纹的需求量越来越大，对精度的要求越来越高。

There are different types of personal loans available.

有许多不同类型的个人贷款优惠。

The above mentioned teaching model of spiral rising can be used to avoid rigidness in teaching.

上述螺旋式上升的教学模式，可以避免教学形成模式後的僵化现象。