查询词典 thin coating

By diffusion of heavy metal ion into zinc oxide crystal,ACR-1 white antistatic thermal control coating is developed with acrylic resin.The space environment effects on the solar absorbtance of the coating and comparison with silicon white thermal control coating are investigated.

通过在氧化锌晶格中掺入重金属离子，得到具有防静电功能的白色颜料，再以丙烯酸树脂为粘合剂制备出空间飞行器外表面用的 ACR-1防静电白色热控涂层；研究了空间环境效应(包括紫外辐照，电子和质子辐照)对该热控涂层太阳吸收率的影响并与有机硅白色热控涂层进行了比较。

An AlTiN ceramic coating was deposited on the surface of biomedical Ti6Al4V alloy by High Ionic Pulse technology. The properties of biofriction and wear of AlTiN coating in simulated serum lubrication at 37℃ were investigated and compared with that of non-coating Ti6Al4V alloy.

采用高度离子化脉冲工艺在医用钛合金Ti6Al4V表面制备AlTiN涂层；在摩擦磨损试验机上测试了涂层在37℃的模拟人体生理血清液润滑条件下的摩擦磨损性能，并与之和未经涂层的Ti6Al4V合金作比较。

The product offers a perfect solution for the problem of color durableness of mineral coating and makes mineral coating really coexist with nature, really a revolution of coating industry.

改性后的硅酸钾不但具有更为良好的化合性，同时与各种氧化无机色素能良好相容，彻底解决了矿物涂料的色泽问题，使得矿物涂料真正与自然共存，成为涂装行业的一次革命。

To analyze and compare each targets of pre-coating Cu and pre-coating Ni,which are the two pre-coating methods adopted in electrocoating Cu for Cu-cladded steel wire The relative matters needing attention and measures of improvement are put forward,which have important significances for cutting down production cost and improving product qualit

对铜包钢丝在电镀铜过程中采用的两种预镀方法———预镀铜和预镀镍的各项指标进行分析比较，提出相应的注意事项和改进措施，对于降低生产成本，提高产品质量意义甚大。

To analyze and compare each targets of pre-coating Cu and pre-coating Ni,which are the two pre-coating methods adopted in electrocoating Cu for Cu-cladded steel wireThe relative matters needing attention and measures of improvement are put forward,which have important significances for cutting down production cost and improving product qualit

对铜包钢丝在电镀铜过程中采用的两种预镀方法———预镀铜和预镀镍的各项指标进行分析比较，提出相应的注意事项和改进措施，对于降低生产成本，提高产品质量意义甚大。

In order to research the influence of polyaniline on acrylic anticorrosive coating, the polyaniline/acrylic anticorrosive coating that the mass rate of emeraldine base form of polyaniline in coating was 0%, 1.5%, 3%, 5%, 10% were prepared, and theirs anticorrosive performance in 3.5% NaCl solution was studied by Tafel and EIS.

为了研究本征态聚苯胺对丙烯酸涂层防腐性能的影响，制备了本征态聚苯胺质量分数分别为0%，1%，3%，5%及10%的聚苯胺／丙烯酸防腐涂层，应用Tafel极化曲线和电化学阻抗谱方法对比了其在3.5% NaCl溶液中的防腐性能。

The results show that, there is a white zonal area between the AZ61 and Al-alloyed coating, which indicates that a good metallurgical bonding is obtained. The coating shows typical hypoeutectic structure. Due to lots of Mg17Al12 phases in Al-alloyed coating, the corrosion resistance of AZ61 magnesium alloy is increased obviously.

结果表明，涂层与基体形成了扩散白亮带，实现了较好的冶金结合；涂层具有亚共晶组织的特点；大量的Mg17Al12相存在于涂层表面是耐腐蚀性能提高的主要原因。

The results show that the composite coating is metallurgically bonded to the substrate and the microstructure is fine and uniform. The hardness of the composite coating is up to 400 HV, which is 2.5 times that of the substrate. Under room temperature and oil lubrication condition, the sliding wear tests indicate the friction coefficient and weight loss of the composite coating are smaller than those of substrate. The worn surface of the composite coatings is much smoother than that of the substrate, without grooves and crater.

结果表明，复合材料涂层与基体形成良好的冶金结合，微观组织细小、均匀；复合材料涂层硬度达400HV，约为基体的2.5倍；在室温油润滑条件下，滑动磨损试验表明复合材料涂层摩擦系数和失重均小于基体，磨损表面划痕较浅且平滑，无明显的犁沟、粘着、剥落现象；激光表面合金化显著提高了材料的耐磨性。

Alumina sols of different content were prepared by using Al3 as precusor, water as solvent, nitric acid as peptizer, ethylacetoacetate and polyvinylpyrrolidone as modified menstruum. We used dip-coating method and spin-coating method prepared of alumina films on the plane glass and used dip-coating method and rising liquid method inside the wall of the fiber.

以仲丁醇铝为前驱物、水为溶剂、硝酸为胶溶剂、同时加入乙酰乙酸乙酯和聚乙烯吡咯烷酮作为改性剂制备了不同浓度的氧化铝溶胶用提拉法和旋覆法在平板玻璃上镀膜，同时用提拉法和液面上升法在石英毛细管内壁上镀膜。

Because of having surplus weld reinforcement height and irregular seam form as well as the influences of polyethylene raw materials and coating process, the quality problems of ununiformity in thickness of 3PE coating and coating thickness reduction on helical seam occur.

由于螺旋埋弧焊管存在焊缝余高超高和焊缝形貌不规整等现象，加之聚乙烯原材料及涂敷工艺等因素的影响，会使三层PE防腐涂层出现涂层厚度不均、焊缝处涂层减薄等质量问题。

If you were not , and OS X just booted normally, have no fear.

如果你没有，和OS X刚刚启动通常，没有恐惧。

I only want to preserve our all .

我只想保存好我们的一切