查询词典 technological process

So, the paper brings out a feed forward cascade PID control method in order to optimize control process according to technological flow and control theory. It promotes the system stability and decreases the cost of the water process.

通过分析处理工艺流程及生产控制原理提出了前馈串级控制的控制方法，利用该控制方法对控制过程优化，提高了系统适应能力，降低了污水处理加药费用，同时保证了回注油田污水的质量。

The technological scheme is that under the conditions one reaction temperature 40-200 deg.c, reaction pressure from normal pressure to 6.0 MPa and reaction velocity of 0.5-3/hr, C4 mixture as the main material is made to contact with catalyst to produce isooctene. The production process may be used in industrial production of selective C4 mixture dimerizing process to prepare isooctene.

本发明通过采用以混合碳四为原料，在反应温度为40～200℃，反应压力为常压～6.0MPa，反应液体体积空速为0.5～3小时-1条件下，反应原料与催化剂接触生成异辛烯的该技术方案较好地解决了上述问题，可用于混合碳四选择性二聚制异辛烯的工业生产中。

At first, the rought C〓F〓 mixed gases are obtained by pyrolysis process of R22. A experimental pyrolysis device is designed and made by ourself. The optimum operating conditions are offered in the paper. Secondly, the much efforts is on the synthesis of R134. After through the discussion of basic thermodynamics and kinetics, selecting and preparating catalyst, it is possible that the synthesis of R134 by pyrolyzed gases hydrogenation. Base on the character of catalytic process, the kinetics equation about C〓F〓 catalytic hydrogenation is established. The rate constant of the reaction is obtained through experiment data regression. In order to achieve higher yield of R134, some optimum technological conditions is determined.

论文首先对R22裂解制成四氟乙烯混合原料气的裂解过程进行了讨论，自行设计和制作裂解反应装置，并确定裂解反应的最佳操作条件；然后，重点对R134的合成进行基础研究，分别从热力学和动力学的角度探讨以含四氟乙烯的R22裂解混合气为原料合成R134这一全新工艺的可能性，选择和制备加氢催化剂，根据催化过程特点建立四氟乙烯催化加氢反应的总包动力学方程，并在此基础上自行设计和制作中试合成装置，获得了以裂解混合气为原料合成R134的最佳工艺条件，为R134的工业化生产提供了必要的理论依据和实验基础。

Finally, the research contents, significance and technological rotes of the dissertation are expanded, with which followed a brief introduction to the dissertations architecture.In chapter 2, the primary theories of process simulation are researched. The basis concept of process structure model and simulation model are given firstly combined with the case.

为此，本文主要内容包括：第一章讨论了本文的研究背景，研究了过程管理产生的背景及进行过程仿真的必要性，分析了过程仿真的特点及当前过程仿真建模技术的现状，提出了全文研究工作的意义、目标及论文的主要研究内容、技术路线。

An introduction was made on the design of the essential processing drawing and the part_processing procedure drawing , the selection of the pressing direction, the makeup design of the technological process, and the location of the drawing ribbings in designing the pressing process of the front part of the right_rear wheel hood of Fukang cars.

介绍了富康轿车右后轮罩前部冲压工艺设计中的加工要领图、工序制件图设计及冲压方向选择、工艺补充设计和拉伸筋设置等。

So we must adjust the technological process and parameters of the milling process to reach the improved effects.

因此调整了缩绒工艺流程和参数，达到改进的效果。

In basic properties of silver grass, the basic biology construction, fiber morphology, buffering capacity , surface wet ability and longitudinal tensile strength was mainly studied; in manufacturing process of SPB, the effect of board density and UF addition on physical and mechanical properties of SPB was mainly discussed, and By means of test of orthogonal experimental design and searching test, the relationship between moisture content , hot-pressing temperature , water-proofing agent addition and the TS of SPB was studied in detail. Through the study of the test production process of SPB, the best technological conditions were determined.

在荻草基本性质方面，主要研究了荻草的基本生物构造、纤维形态、化学成分、酸碱缓冲容量以及荻草的表面润湿性和纵向抗拉强度；在荻草刨花板制造工艺方面，主要讨论了不同密度、施胶量与板材物理力学性能之间的关系，并通过正交试验的方法深入研究了热压温度、板坯含水率以及防水剂施胶量对荻草刨花板吸水厚度膨胀率的影响，通过研究确定了较佳的试验生产荻草刨花板的工艺条件。

When the equivalent strain rate is relatively low, this influence can be neglected and the compression process can be considered as an isothermal process. While the equivalent strain rate is high, this influence is of importance and the compression process can be approximately considered as an adiabatic process.

当等效应变速率很小时，变形热效应对流动应力的影响可忽略不计，压缩过程可近似认为是等温过程；当等效应变速率较大时，变形热效应对流动应力的影响相当显著，压缩过程基本上成为绝热过程。

When the equivalent strain rate is relatively low, this influence can beneglected and the compression process can be considered as an isothermal process. While the equivalent strain rate is high, this influence is of importance and the compression process can be approximately considered as an adiabatic process.

当等效应变速率很小时，变形热效应对流动应力的影响可忽略不计，压缩过程可近似认为是等温过程；当等效应变速率较大时，变形热效应对流动应力的影响相当显著，压缩过程基本上成为绝热过程。

Treating with coils as aeolotropy, this paper brings forward a set of mathematical mode for computing internal stress distribution of coil in the process of coil coiling, in which some factors are taken into account, such as the transverse distribution of shape, crown and curl tension of the strip, the friction between the strip and the reel, the friction between strips, and etc. Because the reel shrinkage and the inner circle of the strip losing radial restrain and circumferential restrain can induce interlayer slipping and the change of the whole coil compactedness , the assumption concerned ——"virtual reel" in the process of coil uncoiling is put forward, which takes the form of slow action to express the uncoiling process and, therefore clearly simulates the variation course of internal stress distribution of coil in the process of coil uncoiling.

考虑到带材板凸度、卷取张力的横向分布以及带材与卷筒之间、带材与带材之间的摩擦力等因素的影响，并将钢卷按各向异性体处理，提出一套计算卷取过程中钢卷内部应力分布的数学模型；同时考虑到卸卷过程中由于卷筒的收缩，钢卷内圈失去径向和周向约束而引起层间滑移及整个钢卷紧密程度发生变化，提出钢卷卸卷过程中有关"虚拟卷筒"假设，将卸卷过程以"慢动作"的形式表示出来，清楚地模拟出卸卷过程中钢卷内部应力分布的变化历程。

Don not attempt to do something which you can not to do.

不要企图做那些办不到的事情。

The expression of CTGF and TNF-αweredetected by immunochemistry and the number of Clara Cells was calculated.

光镜下观察肺组织的病理变化，采用免疫组化染色观察肺组织中结缔组织生长因子和肿瘤坏死因子-α的表达和Clara细胞的数量。