查询词典 stringer plate

Structure form adopts converse triangle beam double-hole connection welded by general electric trolley wall plate and steel plate, connection shaft, triangle beam bottom is connected with girder by nut and thrust bearing, triangle beam could rotate 360 degrees horizontally, thus realize whole set electric trolley horizontal rotation, largely reduce curve track curvature radius of electric hoist traveling mechanism.

描述： 结构形式采取通用电动小车墙板与一个钢板和连接轴组焊的倒三角形吊梁双孔连接，三角吊梁下面通过螺母及推力轴承与一个横梁连接，三角吊梁相对横梁可在水平方向做360度旋转，从而实现电动小车的整体水平方向转动，大大减小了电动葫芦运行机构弧形轨道曲率半径。

In order to adjusting plate electrization, some servo-motors replacing mechanism as actuator were installed in the gap of the plate cylinder.

在印版滚筒的空当安装伺服电机作为执行机构来代替机械部分的动作，以实现调整印版的电气化

In order to adjusting plate electrization,some servo-motors replacing mechanism as actuator were installed in the gap of the plate cylinder.

在印版滚筒的空当安装伺服电机作为执行机构来代替机械部分的动作，以实现调整印版的电气化；通过光电头自动检测套印误差，并将误差信息反馈给伺服放大器，构成闭环控制系统。

Electrotype: A duplicate relief printing plate made electrolytically by depositing copper on a wax mould taken from an original plate or type and backing it with a lead alloy.

电铸版：是一种复制凸版式。先用蜡在原身版式或字版上套出铸模，把铜用电解法沉积于蜡铸上，然后用铅合金衬背而成。

Because of the time limit,we investigated the bipolar plate voltage of electrolyzer only.The result shows that the time and the dose of sulfonating agent are key factors of controlling the bipolar plate voltage of electrolyzer.

由于时间仓促，仅对电解槽两极板间电压进行实验，结果表明磺化时间以及实验中磺化剂的用量都是控制电解槽两极板间电压的主要因素。

Warm up there are two ways: a oil bath warming up, that is, the blank 套锅 direct warming up, the other a hot-plate warming up, that is, with a electrothermic plate in pot direct thermal.

预热方法有两种：一种用油浴预热，即用夹套锅直接预热，另一种用热板预热，即用电热板装置在预热锅内直接热的方法。

Warm up there are two ways: a oil bath warming up, that is, with a melting pot of warm up jacket, and the other a electrothermic plate warming up, that is, with a electrothermic plate in the pot, direct warming up.

预热方法有两种：一种用油浴预热，即用夹套熔锅预热；另一种用电热板预热，即用电热板装置在预热锅里直接预热。

Version before the electrothermic Board clean surface treatment and gilding, pressure on the back of the concaveconvex zinc version designated some skin, a milky white gum toppedwith of the slightly larger than zinc version of cloth version adocumented Zinc plate location and business card printing and membership card modes on the electrothermic, and then you paste in the electrothermic version of Zinc plate cloth top, at the end of platforms put some hard paper on closing and heating power connected to 80-90 ° c hot press about 15 minutes, so that the zinc version bridgeis the electrothermic Board.

装版前应将电热板表面处理洁净，并在烫金，压凹凸锌版背面划一些条痕，将一块涂有乳白胶的稍大于锌版的布块按确定的锌版装版位置和制卡和会员卡制作方式粘贴在电热板上，再将锌版粘贴在电热板布块上面，在底台板上放些硬纸合压，并将电源接通加热至80-90℃，热压15分钟左右，使锌版牢固粘贴在电热板上。

Original plate: Relief printing plate produced bu7 photomechanical etching as distinct from electrotyping.

原身版：用照相晒版蚀刻方法造成的凸版。有别于电镀版。

GY also produces metal embosser machine, three roller calendering machine, plastic extrusion assembling machine, filming machine, plastic extrusion plate production line, PVC plate production line, embossing devices etc.

公司还生产金属压花机、三辊压光机、塑料流延膜机组、涂膜机组、塑料挤出板材生产线、PVC片材机生产线，压花装置等机械类产品，且出口欧洲、非洲诸国，并已通过CE-marketing认证。19楼空间JCANh

May be considered the equivalent of 5.9 rock in terms of relative technical ability required.

有很多85至90度冰壁艰苦的绳距，差不多是攀岩5.9所需要的技巧及能力。

Yes. Please have a seat, and we'll call you.

是的。请坐，我会叫您的。