查询词典 stretch modulus

This paper introduces the method in measuring the elastic modulus E of Epon photoelas-tic materials by means of the electrical measurement at normal temperatures and comparesthe method with the levev extensometer.

本文介绍常温下用电测法测环氧树脂光弹性材料弹性模量E的方法，并与杠杆引伸仪法做了比较。

Given the least favorable load case, if the shear stress increase in the jointing plane of the spliced structure needs to be limited under 10%,the modulus variance of new-old surface layer and base should not exceed 30%-40%.

在最不利荷载工况下，如果要使得拼接结构拼接面上的剪应力增加不超过10%，新老面层、新老基层的模量差异应不超过30%~40%。

The first part of our experiment is the elastic modulus measurement of human fresh fibular shaft and 317L stainless steel, and in second part, finite element models of fibula under different operational status were set up, stress distribution was cal...

实验分两部分进行，首先测定人新鲜腓骨和 31 7L医用不锈钢的弹性模量，然后运用有限元程序软件分别建立各术式下腓骨的有限元模型，进行应力计算，并经统计学方法处理。

The modal tests of PCB and PCB assembly (free boundary condition and fixed boundary condition) were carried out. The equivalent elastic modulus and damping parameters of PCB can be gained, and the fixed boundary condition of finite element model was also determined. These will help to the following work.Second, drop impact tests of three different heights were carried out. Strains and acceleration responses of PCB were measured. Failed BGA packages of different test conditions were dyeing, and cross section analysis of failed solder joints was conducted.

针对JEDEC标准试件的局限性，提出了设计便于统计学研究焊点可靠性的试验试件的构想，利用有限元模态分析方法确定并验证了用圆形PCB组件替代JEDEC标准试件的可行性；通过一系列模态试验和有限元模态分析，确定了圆形PCB组件的相关试验参数，这不仅为跌落碰撞下PCB组件有限元模拟确定了较为合理准确的有限元模型，而且为正确地评价跌落碰撞下PCB组件的可靠性问题奠定了基础。2。

The modal tests of PCB and PCB assembly (free boundary condition and fixed boundary condition) were carried out. The equivalent elastic modulus and damping parameters of PCB can be gained, and the fixed boundary condition of finite element model was also determined. These will help to the following work. Second, drop impact tests of three different heights were carried out. Strains and acceleration responses of PCB were measured. Failed BGA packages of different test conditions were dyeing, and cross section analysis of failed solder joints was conducted. It was found in our drop tests that the root cause of lead-free solder joints under drop impact was the combined effect of mechanical shock and PCB bending vibration.

针对JEDEC标准试件的局限性，提出了设计便于统计学研究焊点可靠性的试验试件的构想，利用有限元模态分析方法确定并验证了用圆形PCB组件替代JEDEC标准试件的可行性；通过一系列模态试验和有限元模态分析，确定了圆形PCB组件的相关试验参数，这不仅为跌落碰撞下PCB组件有限元模拟确定了较为合理准确的有限元模型，而且为正确地评价跌落碰撞下PCB组件的可靠性问题奠定了基础。

This paper introduces the design method, constitution modulus, system's flow chart and function of this system.

介绍了该系统的设计方法、组成模块、系统流程和功能。

A series of porous metallic matrix with various porosity and good shapes were manufactured through adjusting the partitioning among Ni-Cr filler, high temperature solid grains and foamer by loose powder sintering. The elastic modulus of the matrix was measured.

以松装烧结方法为基础，通过调整Ni-Cr合金钎料、高温固相颗粒和造孔剂的配比，采用合适的烧结工艺，制备出具有不同孔隙率、形貌较好的多孔金属胎体试样，并测量了胎体试样的弹性模量。

And their improved methods were also researched, for example the force density method with the triangle element transformed the three links, surface stress density method, surface stress density method of sub-structure and nonlinear finite element method of little youngs modulus.

并且对它们的改进方法，比如三角形单元转化成三杆单元的力密度法、面力密度法、考虑子结构的面力密度法和小杨氏模量的非线性有限元法进行了深入的探讨。

Results. PVA-C compressive elastic modulus increased with increasing PVA concentration and number of FTC's.

结果：PVA-C压缩弹性模量随着PVA浓度和FTC数的升高而增加。

For spheres with constant diameter D, the grading modulus G and the specific surface of a sphere are identical, that is, G =(πD2)/(πD3/6)= 6/D.

那些集料颗粒。对于直径 D 恒定的球体，级配模量 G 和球体的比表面是同一的，即 G =(πD2)/(πD3/6)= 6/D。

Bob Eckert has been chairman and chief executive of Mattel for eight years.

美泰董事长兼首席执行官鲍勃·埃克尔特在任已8年。

The outlook for honors and disgraces carries on and surpasses the traditional outlook for honors and disgraces theoretically, and carries on and develops the theory of construction of socialist mora...

社会主义荣辱观的提出在理论上是对传统荣辱观的一次继承和超越，是对社会主义道德建设理论的继承和发展，在实践上有利于形成良好的社会风尚。