查询词典 steering column

The handling stability is analyzed, mainly the steering transient response test of steering wheel step input、 the steering transient response test of steering wheel angle pulse input、 return-ability test、 steady static circular test and central steering test are carried out. With those test, how the front suspension system can influence the handling and stability performance is investigated.

在此基础上进一步建立了整车模型，包括前悬架系统、后悬架系统、转向系统、前轮胎系统、后轮胎系统、车身系统，分析了该车的操纵稳定性，主要进行了稳态回转试验、转向盘角阶跃输入、转向盘角脉冲输入、转向回正试验、转向盘中间位置转向试验，并通过这些试验来考察了前悬架对操纵稳定性的影响。

It possesses the steering cylinder assembly testing line of Recirculating Ball-rack steering gear, Rack and pinion steering gear and EPS and the valve production testing line of Recirculating Ball-rack steering gear and Rack and pinion steering gear.

拥有循环球式转向器、齿轮齿条式转向器、可溃电助力式转向管柱总成装配检测线和循环球式、齿轮齿条式液压助力转阀生产检测线。

Rudder equipment 3.2.1. Steering Gear 舵机 The steering gear is designed to comply with the requirements of the Rules. Arrangement of steering gear according to G.A. Plan in steering gear compartment. The gear to be an electrohydraulic piston-type steering gear; driven by two (2) sets of hydraulic pump units. The design to comply with the requirements of the flap rudder maker.

JIANGSU EASTERN SHIPYARD 江苏东方造船有限公司 44 1100TEU 集装箱船建造规格书舵机的设计应满足规范要求，并且舵机的布置根据舵机舱总布置图，舵机型号为电动-液压活塞式，由2套液压泵组单元驱动，并且其设计应满足襟翼舵制造商的要求。

The manual steering system is composed of steering wheel,shaft and column,steering gear and pitman arm,steering knuckles and ball joint,spindle assembly,etc.

手动转向系统包括方向盘，转向轴和转向柱，转向器，转向摇臂，转向节，转向节球头以及转向轴总成等部件。

The conclusions were as follows: theνO-H andνC=O IR absorption maxima shifted towards higher wave numbers after imprinting 17β-estradiol on TFMAA-co-TRIM copolymer with the red shift of theνO-H groups being apparent after precipitation polymerization for 16h while that forνC=O groups being observed after polymerization for 24h. A strong interaction between TFMAA and 17β-estradiol was confirmed by the high selectivity for 17β-estradiol, as indicted by the values of the separation factor of isomers of 17β-estradiol/17α-estradiol (2.28) and the imprinted factor (3.01). Particle diameter of TFMAA-co-TRIM polymer was between 300 nm and 1.5μm, which suited well for solid phase sorbent throughout at low column pressure. The recognition of imprinting TFMAA-co-TRIM polymer for sterol molecules was driven by enthalpy eluted with acetronitile, and low temperature was in favor of the separation of sterol structure analogues on imprinting column. TFMAA-co-TRIM polymer possessed of determinate anti-heat stability, with melting point beginning at 255.84℃, Tp=257.40℃, control TFMAA-co-TRIM polymer and imprinting TFMAA-co-TRIM polymer were respectively decompounded at 267.79℃and 343.11℃, and solid micro-extraction noddle prepared by the special polymerization also showed definite recognition for 17β-estradiol by GC/MS detecting at 270℃. By selection of various washing and elution solvents, elution reagents of close polymerization system were of more advantage in template molecules retention and recognition on molecularly imprinted solid phase extraction column. At a certain extent, progesterone, 17α-estradiol, 17β-estradiol and 4-androstene-3, 17-dione could be intercepted on the MISPE column. Especially, MISPE had high selectivity for progesterone, and imprinting TFMAA-co-TRIM polymer could achieve adsorption balance within 50 min by absorption kinetics test for 17β-estradiol. However, MISPE column showed better selectivity and enrichment property for 17β-estradiol than C18 and CSPE columns according to the data from HPLC and GC/MS analyses. Recovery of 17β-estradiol on MISPE column was up to 85.5% while when prime extracting solution of milk powder was sampled, the recovery of CSPE and C18 columns were 43.7% and 30.7%, respectively.

通过研究阐明：紫外聚合产物TFMAA-co-TRIM中的νO-H振动吸收峰在聚合16h后红移，νC=O振动吸收峰在聚合24h后红移；TFMAA-co-TRIM对雌二醇异构体的印迹因子达到了3.01，α为2.28，优于其它功能单体参与得到的聚合物识别特性；TFMAA-co-TRIM聚合物粒径介于300 nm至1.5μm之间，作为色谱固定相具有良好的通量和低的柱压；在乙腈流动相中，TFMAA-co-TRIM分子印迹固定相的分离过程主要被焓驱动，低温有利于分子印迹固定相分离甾醇结构类似物；TFMAA-co-TRIM分子印迹聚合物在255.84℃时开始熔融，Tp=257.40℃，聚合物CP的降解温度在267.79℃，MIP降解温度在343.11℃，制备的固相微萃取头初步经GC/MS 270℃的耐热性测定；不同的洗提溶剂筛选证明了选择接近聚合溶剂的洗脱体系更有利于MISPE发挥识别效应；分子印迹固相萃取柱对孕酮、17α-雌二醇、17β-雌二醇和雄烯二酮都具有不同程度的保留特性，可作为此类化合物的吸附材料，特别对孕酮强保留的富集特性，可作为孕酮的选择性识别吸附剂，其分子印迹聚合物对17β-雌二醇的吸附动力学测定显示在50 min内基本达到吸附平衡，具有作为传感器核心敏感材料的潜力；对比萃取奶粉中17β-雌二醇性能，MISPE柱比非分子印迹固相萃取柱和C18柱具有更高的保留，回收率依次为85.5%，43.7%和30.7%。

The load transfer and settlement behavior from the simulation results are also analyzed: most of the column load concentrates on the enlarged column cap, and distributes quickly, there is more load attenuation at the variable section. The skin friction of enlarged column cap develops more adequately than underside column. The column settlement concentrates on enlarged column cap, and soil settlement concentrates on a little area below the variable section.

利用三维数值模拟分析了钉形搅拌桩复合地基的荷载传递和变形特性：钉形搅拌桩桩身荷载主要集中在扩大头部分，且衰减较快，变截面处桩身轴力有较大衰减，扩大头桩侧摩阻力较大，下部桩体侧摩阻力较小；桩身变形集中在扩大头，桩间土变形则集中在变截面以下较短范围内。

A complete range of steering parts such as knuckles, steering cylinders and repair kits, bushings and bearings, bell cranks, tie-rods, hand wheels, horn kits, power steering motors and pumps, king pin kits and other steering system parts.

我们拥有完整的转向系统配件，例如转向节、转向油缸及修理包、衬套及轴承、转向拉杆、手轮、喇叭及修理包、动力转向马达及油泵、中心销及该系统的其它配件。

The use of the variance steering ratio can not only raise the steering stability under the high vehicle speed, but also reduce the uncomfortable feeling and steering burden. This is helpful for the subjective evaluation of four-wheel steering vehicle.

采用变转向比方式的四轮转向车辆，不仅能够提高车辆高速时的操纵稳定性能，还能减少驾驶员转向时的不适应和负担，改善对四轮转向车辆操纵稳定性的主观评价。

It also introduced selecting methods of the power redirectors in the steering-system design. Moreover it also did the further research on the power redirectors matching and coordination problem of the suspension system and the steering-system, calculated steering wheel strength and momental gradient when the heavy-duty vehicle matched two kind of power redirectors, did entire vehicle performance simulation research on two matching schemes of the suspension system and the steering-system.

还介绍了在转向系统的设计过程中动力转向器的选型方法，另外还针对动力转向器匹配及转向系统与悬架系统匹配问题做了进一步的研究，对重型汽车匹配两种动力转向器时车辆的转向盘力和力矩梯度进行了计算，并对两种转向系统、悬架系统匹配方案进行了整车性能的仿真研究。

The present paper analyzes the effect of EPS on steering performance. The new system of evaluation includes steering maneuverability, steering returnability, on-center handling performance, steering hand-wheel vibration, servo motion sensitivity and assist characteristics. Some relevant evaluation indexes are also discussed here.

针对电动助力转向的结构特点，本文分析了电动助力转向对汽车转向性能的影响，提出从转向轻便性、转向回正性、转向盘中间位置区域性能、转向盘振动、随动灵敏度和助力特性等方面进行电动助力转向系统转向性能的客观评价，并探讨了相应的评价指标，对EPS系统的设计以及相关试验标准的确定有一定的指导意义。

If you were not , and OS X just booted normally, have no fear.

如果你没有，和OS X刚刚启动通常，没有恐惧。

I only want to preserve our all .

我只想保存好我们的一切