查询词典 socketed screw

And at this basement, analyzes the matching design between screw propeller and diesel engine, according design theory of screw propeller chart.

目前常用的螺旋桨图谱匹配设计涉及大量图、表及繁多复杂的计算公式，并且各图表有特定的适用范围，不利于设计应用和推广；船舶冷却系统中冷却水流量、水泵排量等主要依据主机标定点设计，而船舶在实际航行过程中主机主要运行在部分负荷状态，这样就造成了冷却能力过剩，冷却水温度过低，影响主机性能的发挥。

Therefore, in order to screw suction port separated from the oil discharge screw thread section is greater than the length of at least one lead.

因此，为了使螺杆能吸、排油口分隔开来，螺杆的螺纹段的长度至少要大于一个导程。

Therefore, in order to enable the screw to smoke, Pai oil separated from the mouth, screw thread length is greater than at least one lead.

因此，为了使螺杆能吸、排油口分隔开来，螺杆的螺纹段的长度至少要大于一个导程。

Fig. 11 Measure screw thread pitch using screw gauge

图11。用螺纹规测量螺距的方法

If there's a screw-up, it's your screw-up.

如果出了麻烦就是你的麻烦

Focusing on the interaction among the screws,the paper analyzed the current method of determining propulsive factor based on ship s self-propulsion test with three-screw and presented a new method to test and analyzed propulsive factor of ship with multi-screw.

针对多桨船螺旋桨间互相干扰的影响，通过对三桨船自航试验推进因子分析方法进行分析探讨，提出新的三桨及以上的多桨船船模自航试验方法和其推进因子分析方法。

Hydraulic screw down system of cold rolling sheet plant of Benxi Iron and Steel Company was studied,physical and mathematical models of every part of hydraulic screw down were established and transfer function of the whole system under position control was deduced.

通过对本钢冷轧厂四辊冷带轧机液压压下系统的研究，对液压压下系统的各个环节建立了物理和数学模型，推导出了整个系统在位置控制方式下的传递函数。

Hollow screw, anchor screw fixation for the treatment of knee PCL tibial attachment avulsion fracture is simple, reliable and effective.

空心钉、锚钉内固定治疗膝PCL胫骨附着部撕脱骨折，操作简便，固定牢靠，疗效满意。

Main various types of plastic extrusion machines, injection molding machines, chemical fiber spinning extruder, rubber tube extruder screw machine screw, Liao Tong, flange, such as printing network box.

主营各种型号的塑料挤出机、注塑机、化纤纺丝挤出机、橡胶挤出机机筒螺杆螺杆、料筒、法兰印花网框等。

Detect drive way too much space is a fixed power input shaft and output shaft rotation shaking, in the case of the transmission structure of conventional design and manufacture of machine tools, the transmission output shaft angle space at more than ten degrees to the dozens of degrees Transmission gap caused by too large spiral screw groove surface then there is obvious marks, thus affecting the machining accuracy of the screw.

检测驱动方式太多空间是一个固定的动力输入轴与输出轴旋转摇晃在常规情况下传动结构设计和制造的机床，传动输出轴角空间超过度到10度的数十个输电差距过大造成的螺旋槽螺旋面则有明显的标志，从而影响了螺丝加工精度。

There had been a moment during the breakfast meeting, though, after the backslapping and the small talk and when all of us were seated, with Vice President Cheney eating his eggs Benedict impassively and Karl Rove at the far end of the table discreetly checking his BlackBerry, that I witnessed a different side of the man.

那次早餐会期间，在表示过关心和寒暄以后，我们所有人坐了下来，我注意观察了一下，副总统切尼面无表情地吃着班尼迪克蛋（Eggs benedict，源自美国，以英式松饼、火腿、水煮蛋以及荷兰酱组合而成），卡尔。罗夫在餐桌的远端谨慎地经常查看他的黑莓手机，我目睹了他所不为人知的一面。

Talk Undelete failed; someone else may have undeleted the page first.

Talk 无法删除选定的页面或图像（它可能已经被其他人删除了）。