查询词典 slip

The coefficient of friction in the partial slip regime is lower than that in the mixed fretting regime and gross slip regime .

混合区和滑移区的摩擦系数高于部分滑移区。

Your coating of wax acts as a dry lubricant, it creates slip and decrease friction, if there is wax present on the finish, your towel will slip instead of grab and you wont' hear any noise, in other words, you won't hear any friction.

你的蜡涂层就像是一层乾的润滑剂，如果你的烤漆上是有上蜡的，它会产生光滑表面且降低磨擦力，你的毛巾将会在漆面上滑动而不会被漆面卡住，也不会听到任何的杂音，换句话说，你不会听到任何因为磨擦产生的声音。

The Unified Tire Model for combined slip considering the anisotropy of slip stiffness and friction coefficient is established in chapter three. A more general tire model considering the complex deformation of tire carcass is presented as well.

第三章推导了考虑轮胎纵滑、侧偏刚度明显不同以及摩擦系数各向异性时的联合工况下的统一模型，并给出了考虑胎体复杂变形的更一般情况下的轮胎模型。

Pliocene-Quaternary faulting in grabens around the Ordos block displays predominantly normaldip slip displacements with a right-lateral or left-lateral slip component,indicating a NW-trending extension.

鄂尔多斯周缘地堑系上新世～第四纪的断裂作用表征为以正向倾滑活动为主，同时具有右旋或左旋走滑分量的运动型式，指示了NW-SE向地壳引张作用。

Results show that in contrast to no-slip boundary conditions, slip boundary conditions would allow the displacement of contact line along the wall and have a more precise prediction of interface distortion without neglecting the wall effects.

由模拟结果可看出，相对於不滑动边界，滑动边界设定使壁面接触线可在壁面上移动，能有效预测流体界面弯曲变化情形，且不会忽略壁面之影响。

Slip a pinkie in at the heel while baby is standing - there should be enough room between the shoe and the munchkin's heel to allow your pinkie or a pencil to slip in easily.

支路一pinkie在在脚跟，而婴儿是常设-应该有足够的空间之间的擦鞋和芒奇金的致命弱点，让您的p inkie或铅笔滑倒在容易。

The numerical results of yield strength, based on considering the lamellar microstructure and the deformation mechanisms such as ordinary slip systems and true twinnings in PST crystals composed of and phase, is obtained by using calculating of resolved shear stresses in all slip systems based on micromechanical method.

基于PST晶体的微结构和相及2相普通位错和孪晶滑移启动，结合细观力学方法，通过数值模拟两相中的各滑移系上的分切应力，得出PST晶体屈服应力和外加载荷与片层之间夹角的关系。

The failures of slip-oil pump steady pin bolt and slip-oil separated valve made by copper alloy for the part of component was studied and analysis.

而零组件部份，分别选用304材质所制成之滑油泵稳梢螺栓及青铜材质所制成之柴油隔舱阀破坏作一研究探讨与分析。

In the experiment of this study, the failure structures of pipeline of exhaust system, rib material of water tank, slip-oil steady pin bolt and slip-oil separated valve made by copper alloy under water were cut individual with suit size for specimen. The X-ray, PT non-fracture detection, observation of metal micro-structure, hardness test, element spectrometer, SEM and EDS were used to investigate the mechanism of corrosion and failure.

实验首先将长期使用於水下环境之排烟系统管路、水柜肋材、滑油泵稳梢螺栓及船舶舱间柴油系统用隔舱阀之破损构件，分别裁取适当尺度之试件，藉由X-ray、PT非破坏检验、金相显微组织观察、硬度实验、腐蚀生成物机制研究、分光分析仪成分分析及利用SEM进行破断面形貌观察与EDS元素成分分析等实验。

The temperature of flue gas out of air preheater in boiler is normally about 120～180℃, the flue gas enter the absorb tower from the bottom via pre-deduster and is accelerated by venturi tube at the bottom of absorb tower, then is taken to circulating fluid bed. The materials are in the circulating fluid bed, due to the effect of flow, the gas-phase and solid-phase generate fierce turbulence and combination and are fully contacted, then form polymers constantly during the ascending and return downward, while the polymers are constantly disassembled during fierce turbulence and elevated by airflow, which makes the slip velocity between gas and solid reach the tenfold times of single slip velocity.

首先从锅炉的空气预热器出来的烟气温度一般为120～180℃左右，通过预除尘器后从底部进入吸收塔，然后烟气通过吸收塔底部的文丘里管的加速，进入循环流化床，物料在循环流化床里，气固两相由于气流的作用，产生激烈的湍动与混合，充分接触，在上升的过程中，不断形成聚团物向下返回，而聚团物在激烈湍动中又不断解体重新被气流提升，使得气固间的滑移速度高达单颗粒滑移速度的数十倍。

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。