查询词典 shear angle

Usually, maximum shear modulus is determined by strain method in laboratory, rather than by shear velocity method in-situ,and based on it,shear modulus ratio and damping ratio of soil can be provided.

最大剪切模量是影响土的动剪切模量比、阻尼比和土层地震反应的最重要参数之一。

Through a great number of experiments, the paper put forward to shear test index of graded broken stone with self-invented instrument, analyzes its influence rule by varying gradation, water content, compactness, shear rate and lateral compression; studies systematically the changing rule of CBR, infiltration index and thermal conductivity by gradation; works out the suitable biggest particle size, key screen openings and range of their reasonable percentage passing; put forward to graded broken stone design methodology based on CBR and shear strength and construction method in perennially frozen soil zone.

本文通过大量试验，利用自行研发设备，提出了级配碎石的抗剪切性能指标，分析了级配、含水量、密实度、剪切速率、侧压力对抗剪切性能的影响规律；系统研究了级配对CBR值、渗水性能、导热性能的影响规律；通过CBR试验和抗剪切试验，得到了最佳级配最大粒径和关键筛孔及其通过率合理变化范围；提出了基于CBR值和剪切强度双指标控制的级配碎石组成设计方法及适宜多年冻土地区的施工工艺。

By considering the influences of initial packing fraction, shear rate and friction coefficient on the shear velocity profile, local packing fraction and coordinate number, we have investigate the mean flow features inside shear granular flows.

根据初始体积分数、剪切率、摩擦系数等对系统内剪切速度廓线、局部体积分数和配位数等的影响规律，分析了剪切颗粒系统的平均流动特征。

The results show that the plasticity zone and dynamically quiescent layer become fine equiaxed recrystallisation under the thermo-mechanical effect, the grains in the heat-affected zone grow up because of the effect of friction heat. When the rotation speed is 2 500 r/min and the welding time is 12 s, good joint is achieved, and the tensile shear strength of the joint reaches 9.24 kN. The tensile shear strength of spot increases with increasing tool rotation speed, with increasing welding time, the strength increases first, while then reduces. The microhardness of plasticity zone is high, but is slightly lower than that of the base metal, the minimum value of microhardness is in the heat affected zone. When the energy input of joint is high, the fracture type of spot is mode Ⅰ, and the tensile shear strength is high; on the contrary, when the energy input of joint is less the fracture type of spot is mode Ⅱ, and the strength is low.

结果表明：塑性区和动态静止层的晶粒在热和力作用下发生动态再结晶形成细小的等轴晶，热影响区的晶粒在摩擦热作用下长大变粗；搅拌头旋转速度为2 500 r/min，焊接时间为12 s时，可以获得力学性能较好的焊点，焊点的剪切强度达到9.24 kN；焊点的剪切强度随搅拌头旋转速度的增大而增大，随焊接时间的延长先增大后减小；塑性区的显微硬度较高，但略小于母材，接头显微硬度的最小值分布在热影响区；焊点热输入量较多时，接头为Ⅰ型断裂，焊点的剪切强度较高；焊点热输入量较少时，接头为Ⅱ型断裂，焊点的强度较低。

Furthermore, finite element program ABAQUS6.5 was also used to simulate experimental course. Results show that the change of ply splice angle will lead to shear stress concentration on 0 ply in splice region. But the average of shear stress along notch root of specimens almost does not change.

采用有限元软件ABAQUS6.5对实验过程进行模拟，得到拼接层角度改变将引起拼接层中0层出现切应力集中，但沿缺口切应力的平均值几乎不变。

A theoretical model for calculating the cutting angle with different crystal planes, orientations and tool orthogonal rakes are described in this paper. It is built with the ultra-precision cutting model by the principle of the maximum specific energy of shear deformation and the mechanism of change of the shear modulus with...

本文利用剪切变形比能最大及单晶材料不同晶面晶向剪切弹性模量不同的原理，结合超精密切削模型，从理论上计算出不同晶面、不同晶向及不同刀具前角超精密切削条件下的剪切角，得到其在不同切削条件下的变化规律，并由此解释了切削加工中由KDP晶体各向异性所导致的工件表面粗糙度的各向异性。

The concept of negative shear zone and negative shear angle are proposed in study.

提出了负剪切角及负变形区的概念。

And the distribution of the magnetic shear angles exhibits the hemisphere sign rule as the asymmetry of helicity. In our dataset, 53% of the active regions in the south hemisphere have positive shear angle and 62

磁场剪切角具有南北半球符号的反对称手征性，在南半球有53％的活动区的磁场剪切角是正的，而在北半球有62％是负的。

The shear angle in the shear plane will crease with the cutting velocity.

切屑剪切平面之剪切角会随著切削速度的增加而增加。

Fractography analysis shows that the global tension failures trimly,because of matrix cracks and tension fracture of fiber and the compression specimens failure in a shear plane about a little angle to the compression loading direction because of delamination and longitudinal fiber shear fracture.

其拉伸断口较为平齐，基体开裂以及纤维拉伸断裂是主要破坏形式；压缩破坏呈现剪切断面，压缩断面和压缩加载方向形成一个较小夹角，层间分层和纵向纤维剪切断裂是其主要破坏形式。

Pradeep Indulkar, a senior official at the Maharashtra state Home Ministry say 101 human were killed and 287 injured.

马哈拉施特拉邦内政部高级官员Pradeep Indulkar称，有101人在冲突中丧生，287人受伤。

Mark Frei, a senior vice president of West, says 80% of West's homeagents have some college education, compared with 30% of those whowork in office-based call centers.

Frei说，该公司80%在家办公的人员都拥有本科学位，而在公司电话中心工作的人中只有30%拥有本科学位。