查询词典 sensitive element

Using it ingeniously to the enterprise image design, points out to make use of traditional element that is not mature place at present, putting forward the design idea of the traditional element that changes because of ages and pursuing of vogue.Expending the tinking of the symbol design in the future. Discuss the design of the adornment doctrine of traditional element from the theories.

所以，本文以探寻&传统元素&的设计开始，引出本文论点，以传统文化为依托，发觉有内涵和象征性的传统元素，再用现代理念进行设计，把它巧妙地运用到企业形象设计中去，及指出现今运用传统元素的不成熟之处，提出&传统元素&在企业形象设计中因时而变及追逐时尚的设计观念。

That is, the constant element for velocity potential, called 0 type element, and linear element for its nor

即对势函数采用线性元(或称之&1&型单元)，而对势函数法向导数采用常数元(或称之&0&型单元)，以这样的0-1混合型边界元剖分计算域的

In this article, a three-dimensional finite element model of large-scale vacuum transfer line is developed, applying ANSYS program and using 3D solid element and shell element.

本文使用ANSYS程序，选用三维体单元和壳单元，建立了减压转油线管系的三维有限元分析模型。

In this article, a three-dimensional finite element model of four-branch-pipe-joint vacuum transfer line is set up, applying ANSYS program and using 3D solid element and shell element.

本文使用ANSYS程序，选用三维体单元和壳单元，建立了减压转油线五通管系的三维有限元分析模型。

This paper is based on the former research taking the No.1 Tong-Lv Bridge as an example; the large universal finite element program Midas/Civil is adopted, a three-dimensional finite element model is established. The static performance, the comparative analysis of influence surfaces, the experimental study and the analysis of a local finite element model of the new style three-span continuous through type bow-string arch bridge is made. With these studies, this paper is aimed at revealing the performance of this kind of construction.

本文在前人研究的基础上，以通吕一号桥为背景，采用空间有限元法对结构形式新颖的三跨连续下承式系杆拱桥的静力性能、影响面比较分析、实桥荷载试验、局部节点分析等进行研究，旨在深入理解该结构形式桥梁的力学性能，为今后相同结构体系桥梁的结构分析提供可以参考的建议。

A finite element analysis on the new method is presented in this paper. Based on the finite element analysis, tension tests of 18 steel bars in different diameters and holes are carried out. The results of tests, which are according with that of finite element analysis, validate the new method to determine real stresses of steel bars by drilling/enlarging small holes. Furthermore, some suggestions in using of the new method are given.

本文针对该新方法进行了有限元分析，并在此基础上进行了18种不同钢筋直径和不同孔径的带孔短钢筋拉伸试验，试验结果与相应有限元计算结果一致，验证了钻／扩孔确定钢筋实际应力的新方法，并提出了若干工程适用建议。

An XML element is everything from the element's start tag to the element's end tag.

一个 XML元素的所有内容是元素的起始标签和终止标签之间的一切内容（起始、终止标签也包含其中）。

According to above, the mini force sensor is designed and the rationality of different way of choosing force element is evaluated, metal strain sheet, pressing-electricity element, pressing-resistance element and practical experiment result.

在此基础之上，设计了微力传感器，对比分析了利用金属应变片、压电晶体、压阻元件作为力敏元件的优劣和可行性以及实际的实验结果。

It includes the following steps: first, choose the speed of operation, direction, protection mode and protection sustaining mode; second, choose the initial point net element and the stop point net element; third, confirm the download/upload port on the two net element; fourth, take route restriction; fifth, taking route calculation; finally, send the route information to user for affirming, if user is satisfied, device completion operation configuration could download.

选定业务的速率和方向和保护方式及保护支持方式；2。选定业务的起始点A网元和终止点Z网元；3。在A网元和Z网元确定业务上下的端口；4。进行路由限制；5。进行路由计算；6。将计算得到的路径信息给用户确认，如果用户满意，确认后可下发设备完成业务配置。

Firstly, two examples, which belong to static analysis and dynamic analysis respectively, were given to show the effectiveness of discrete element method. Then the discrete element method was used to perform dynamic analysis of the Chinese 1 km deep-ocean mining system. The dynamic performance of the entire mining system under different current directions was discussed and compared with that from finite element method.

首先，从静态分析和动态分析两方面，给出2个典型算例，证明该方法的有效性；然后，将离散元方法用于中国1 km深海采矿系统的动力学分析，讨论不同海流方向下整体系统的联动性能，并与有限元方法进行对比。

"Second Life is remarkably easy to work with, and is very popular,"

"第二次生命是显着容易的工作，并且很受欢迎，"

For example, we usually assume that materials are homogeneous and isotropic and free of internal defects or flaws.

为了得到适合有限元分析的模型，我们必须经过如图2所示的简化步骤。