查询词典 process furnace

The novel vacuum furnace is employed in laboratory study. Compared with atmosphere magnesium carbothermic reduction furnace, this new one has the merits of high automation, easy manipulation and fine safety. Vacuum coking, vacuum carbothermic reduction process and magnesium vapory condensation process can be carried out in a furnace.

小型实验结果证明：还原温度升高，还原时间延长，氧化镁还原率增大，添加适量的氟化物对还原反应有促进作用；还原过程中真空度随时间的变化具有规律性，由此可以判断还原反应进行的速度与程度；真空中煤还原氧化镁的条件是：配料时保证C：MgO=3：1，并加入占总料重10％的氟化钙作为催化剂，尽可能的提高反应温度至1500℃以上，保温30～40分钟。

The objectives of this paper were to investigate the simulation and design of continuous multiple-station rolling forming process for a U-Section Steel Bar by CAE software-DEFORMTM Due to the limitation of elements number using a short strip 120mm went through all the stations to simulate the real continuous rolling forming on factory The roller gap was fixed as 0 30mm roll speed was 20 rad/sec and progressive angles were all equal for each rolling process which were the formed angle divided by by the number of station Three rolling processes were selected with 6 9 and 12 stations respectively During simulation processes two cases occurred Case A the strip was through a single station Case B the strip across two stations Because the strip laterals side was stretched and twisted during the process The model of case B closer to the practical process than case A and the calculated stress and strain on the tip of U section for case A were lower than these for case B by up to 15% From the result of case B for each process the stress for 12-station process was smallest 9-station process second and 6-station process next Because less-station can save larger cost and forming time but the bigger stress and strain for 6-station caused wrinkles on lateral sides not found on 9-station and 12-station Therefore 9-station process was a more suitable design than 12-station process smaller stretched and twisted and stress The progressive angles for 12-station was 7 5?

本文主要是以DEFORMTM有限元素软体模拟U型钢片连续道次成型与单一道次成型以确认单一道次模拟的是否可取代连续道次模拟之研究。因DEFORMTM 软体对於网格元素上的限制故使用较短素材120mm通过所有的成型站以模拟工厂实际连续成形方法。辊轮间隙固定为0 3mm；辊轮转速为20 rad/sec；弯曲角度的方法为将成型角度平均除以成型站数。有三种辊轮成型方式被选择分别为6站，9站，与12站。在模拟的过程中有两种现象会产生 Case A，素材通过单一成型站。Case B，素材会通过两个成型站。因为在模拟过程中素材的两端会有拉应力与扭力。Case B的模拟比Case A像实际的制程，并计算应力与应变在U型断面的Tip部中可发现Case A比Case B低约15%。从Case B的每站的结果可以得知，12站的成型应力最小，9站次之，6站最后。

To improve temperature uniformity,trolley electric furnace heated by three districts, in accordance with temperature arrangement method arrange heating elements, compensation for loss of furnace heat mouth, I District II District III district heating elements layout of the different, but the car high-precision temperature furnace heating and insulation in the process of maintaining three districts temperature consistent.

可为用户定做各种规格尺寸高精度高温台车电炉。为提高炉温均匀性，台车电炉采用三区加热，并按均温布丝法布置加热元件，为补偿炉口热损失，I区II区III区加热元件布置范围各不相同，但使高精度高温台车电炉在升温及保温过程中保持三区均温一致。

After having compared the cupola furnace with electric arc furnace on the characteristics of the process of producing spheroidal graphite cast iron steel ingot module and their application effects, the results show that it will prolong the life of steel ingot module and improve the quality of steel ingot by applying arc furnace to melt spheroidal graphite cast iron steel ingot module.

电弧炉技术在球墨铸铁钢锭模生产上的应用赵海兵任元和李梅曹志张涛摘要将冲天炉和电弧炉这两种生产球墨铸铁钢锭模的工艺特点及应用效果进行对比，结果表明，采用电弧炉冶炼球墨铸铁钢锭模能够提高钢锭模使用寿命，改善钢锭质量。关键词球墨铸铁模耗A

Induction Furnace Carburizing Furnace;■ cupola furnace by carbon;■ process by double-carbon;■ steel package with the flow of hot metal by carbon.

感应电炉炉内增碳；■冲天炉炉内增碳；■双联工艺增碳；■炉前铁水包随流增碳。

Consequently, the permeability of cohesive zone in blast furnace can be improved and the total pressure drop in blast furnace can be decreased by use of such sinters. In order to ensure proper MgO content in the BF slag and improve the RDI of sinter, a new process of adding MgO in BF is proposed.MgO; sinter; blast furnace; cohesive zone

本文考察了MgO对烧结工艺及烧结矿冶金性能的影响，提出了合理添加MgO新工艺的建议。1 MgO对烧结工艺的影响1.1 烧结试验在实验室条件下，以各种铁精矿粉为原料，使用j6150 mm烧结杯系统，考察MgO含量对2种碱度(R=1.36和R=1.76)烧结工艺的影响，烧结试验中的MgO以白云石的形式添加，MgO的质量分数分别为1.3 、1.7％、2.1 、2.6 和3.0％，其他烧结工艺参数见表1.1.2 试验结果及。。。。。。

For KISC, the technology shall firstly use high-phosphorus ironstone efficiently which can not completed by the current picking technology or blast furnace process, to greatly reduce ironstone cost that occupies the most proportion of iron and steel production cost, easy cost pressure caused by international and domestic shortage of production materials, induce transportation risk, to assuringly supply KISC with a great deal of cheap raw materials and create great economic profit; Secondly it shall promote KISC to update its products, especially high-added-value products of lowest phosphorus and lowest sulfur, to enhance its ability to adapt market and gain profit; Thirdly it shall improve technical and economic indexes of blast furnace and converter, and be helpful for efficient blast smelting and less-slag melting of converter process; Furthermore the technology shall greatly promote the stable operation of melting process and the control of the production of high-temperature and high-quality casting blank, to realize efficient continuous casting and continuous casting and rolling to improve KISCs production intensification; Finally the technology shall distribute melting functions and optimize production processes, to improve the auto-control of melting and continuous casting, to realize the integrated management of technology, equipment, production organization and management, logistic management, and production running of smelting, continuous casting and rolling.

对昆钢而言，该技术的应用，首先可以经济有效地实现现有采选技术及高炉冶炼所不能完成的高磷铁矿石的利用，大幅度降低在钢铁生产中占绝大比例的原料成本，缓解国际国内生产原料紧张而造成的成本压力，为昆钢创造巨大的经济效益；其次可以促进昆钢产品的升级换代特别是高附加值超低磷、超低硫钢种的开发，增强昆钢的市场适应能力和效益创造能力；再次可促进高炉及转炉技术经济指标的改善，降低生产成本，且利于转炉生产实现高效吹炼和少渣冶炼；此外，该工艺能显著提高冶炼环节的平稳顺行及高温、高质量铸坯生产的可控程度，可实现高效连铸和连铸连轧生产，提高昆钢生产的集约化程度；最后，该工艺能实现冶炼功能的分工和生产流程的优化，可提高昆钢炼钢与连铸生产的计算机自动控制程度，有效促进炼钢—连铸—轧钢的工艺、设备、生产组织和管理、物流管理、生产操作等环节的一体化管理的实现。

The instruments used ATmega16L onboard A / D converter channels to achieve the cold wind pressure, the hot blast pressure, the furnace top pressure and cold wind current capacity four way analog acquisition;used PWM waveform produced by ATmega16L internal timing / Counter to achieve the entire differential pressure ,the cold wind flow and the permeability index three-way analog output for recording instruments; realized the cold wind pressure, the hot blast pressure, the furnace top pressure, the cold wind current capacity and the entire differential pressure five group parameter tour demonstration and the fixed-point demonstration by key-elect key's coordination during demonstration blast furnace permeable index; produced acousto-optics alarm when the permeable index across the upper and lower limits;used RS-485 realizing the communication with the superior computer.

仪表利用ATmega16L自带的A/D转换通道实现对冷风压力、热风压力、炉顶压力及冷风流量四路模拟信号的采集；通过ATmega16L内部的定时/计数器产生的PWM波形来实现对全压差、冷风流量及透气性指数三路模拟量输出供记录仪表使用；通过键选键的配合在显示高炉透气性指数的同时实现冷风压力、热风压力、炉顶压力、冷风流量及全压差五路参数的巡回显示与定点显示；当高炉透气性指数越上、下限时，仪表产生声光报警信号；仪表采用RS-485与上位机实现通信。

The company has a 5-ton electric arc furnace, electroslag furnace set of 1.5 tons, 5 tons an electroslag furnace.

公司拥有5吨电弧炉一套，1.5吨电渣炉一套，5吨电渣炉一套。

Arc furnace,it is put forward that an optimum heat distribution relationship exists between the reaction area and furnace charge area,in view of this,a simple smelting model of submerged?arc furnace is set up.

摘 要 从铁合金矿热炉内的等效电路及其热分布出发，提出冶炼过程中炉内反应区和炉料区之间存在着一个最佳的配热关系，由此而建立起铁合金矿热炉简单的熔炼模型。

The two-acre Dunbar Community Garden in Little Rock has served as a model for several years.

几年来，坐落于小石城，占地两英亩的邓巴社区菜园树立了一个标杆。

Jerry points to the jacket hanging in the bathroom. It's ruined, and unwearable What?

杰瑞指着洗手间里挂着的夹克，毁了，不能穿了）什么？