查询词典 planar developable surface

Single factor experiments were done with the factors including the width of protrusion and the trolley's velocity, which showed that the surface frictional coefficient decreases with the width of protrusion increasing, and doesn't change with the trolley's velocity changing, which was consistent with the results of the orthogonal experiment. A theoretical model of the horizontal projection of a corrugated bionic surface's contact area was built, which showed that the contact area's horizontal projection decreases with width and interval increasing respectively and that the ratio of the contact area's horizontal projection and the vertical load decreases with the vertical load increasing. It indicated that the surface frictional coefficient decreases with the above three factors increasing respectively. Finite element modeling and analysis of interactions of a plate and soils was done using ANSYS, which showed that the plate frictional coefficient is little relative to soil elastic modulus and decreases with vertical surface pressure and that trolley's pull and vertical displacement of bionic surface's control pilot keep constant almost during the plate being pulled. Finite element modeling and analysis of interactions of a corrugated bionic surface and soils was done using ANSYS, which showed that surface frictional coefficient is little relative to soil elastic modulus and decreases with bionic surface's structural parameters and vertical pressure increasing. However, the three factors all didn't affect the surface frictional coefficient remarkably on the condition of 90% dependability. For the first time, bionic surfaces were applied to screw piles, which formed bionic screw piles, and the contrast experiments showed the bionic screw pile had certain resistance-decreasing effects.

建立了波纹型仿生曲面与土壤的接触面积的水平投影的理论模型，表明接触面积的水平投影A随着波纹型仿生曲面突起宽度、两相邻突起间距的增大而减小，接触面积的水平投影与波纹型仿生曲面表面垂直载荷之比随着波纹型仿生曲面表面垂直载荷的增大而减小，进而得出仿生曲面摩擦系数随着波纹型仿生曲面突起宽度、两相邻突起间距以及表面垂直载荷的增大而减小；利用ANSYS软件对平板与土壤的相互作用进行了有限元建模与分析，表明平板摩擦系数与土壤弹性模量关系不大，而随着表面垂直载荷的增大而减小；平板牵引过程中台车牵引力和仿生曲面控制节点垂直方向位移基本保持不变；利用ANSYS软件对波纹型仿生曲面与土壤的相互作用进行了有限元建模与分析，表明波纹型仿生曲面系数在一定范围内基本不受土壤弹性模量的影响，随着波纹型仿生曲面突起宽度、两相邻突起间距以及表面垂直载荷的增大而减小，但在可信度为90％的前提下，三个因素影响都不显著；首次将波纹型仿生曲面应用于与土壤作用方式以挤压为主的螺旋桩，形成仿生螺旋桩，并与普通螺旋桩进行了沉桩对比试验，表明波纹型仿生曲面应用于螺旋桩桩体表面具有明显的降阻作用。

Furthermore, the reconstituted model of planar enveloping hourglass meshing surface is established in the light of the research of 3D surface reconstituted algorithm, and 3D error of the real planar enveloping hourglass meshing surface is derived accordingly.

利用计算机处理技术，提出了测头半径补偿的算法，进行了三维型面重构算法的研究，建立平面包络环面啮合型面重构模型，在此基础上获取了平面包络环面啮合型面三维误差。

The kinematic analysis of a planar cam mechanism can be realiaed by the method that the higher pair is substitute for lower pair, and then it is equivalent to a planar linkage. The main point by the way is how to calculate the radius of curvative of planar cam profile.

对于平面凸轮机构的运动分析可以用高副低代的方法将其转化成平面连杆机构来进行，而高副低代后关键的问题是如何在书籍平面凸轮廓线的基础上求解凸轮的曲率半径。

Experimentally, multi-pores are observed on leukocyte lysed with 3D electrodes and just single pore with planar electrodes. This is believed to be due to more uniform electric field of 3D electrodes than that of planar electrodes. Intracellular elements are extracted through the membrane as observed by increased intensity of Trypan blue when diluted by saline solution. We also demonstrate the lysing percentages at same flow velocity to explain the performance of 3D electrode is superior to that of planar electrode.

在实验方面，可发现细胞在3D 电极的形况下，是有多个破孔出现，有别於在平面电极的单个破洞，也发现当细胞出现破孔时，经由Trypan blue的辅助观察以及在食盐水稀释情况下，细胞内液是往外流出的，另外由裂解比率的结果，3D电极也是优於平面电极。

This thesis investigates the profile extraction and shape optimization on the result of topology optimization of planar compliant mechanisms. The main context includes the following work:(1) summarizing and analyzing the recent research status, some harvest and unsolved problems;(2) analyzing the conceptual design of planar path-generating compliant mechanisms and its mathematical model and tools;(3) Modifying the method of density contour as the method of profile extraction, and developing a method to optimize the density function in the profile extraction according to the requirement of the design of compliant mechanism;(4) developing a method to abstract the compliant mechanism into a form of links and joints by using the principle of connectivity on topology;(5) developing a method of shape optimization of planar path-generating compliant mechanisms, by representing the profile of the abstracted compliant mechanism as simple curves such as straight lines and arcs, establishing the models of the size optimization of the parameters of these curves, so that the compliant mechanism has a machinable shape;(6) At last, proving the feasibleness and effectiveness of the design method by making simulation design and validating it in FEA software.

主要工作包括：(1)分析了柔顺机构拓扑优化和形状优化的研究现状，分析了目前柔顺机构的研究重点、主要成果和尚未解决的问题；(2)分析了基于SIMP的柔顺机构概念设计方法及其相关工具和模型；(3)针对柔顺机构轮廓提取的特殊要求，提出了密度等值线法的改进方案，对密度函数插值点密度值进行优化，提出优化模型和选择优化算法；(4)根据轨迹输出平面全柔顺机构自身的形状特点，提出了轨迹输出平面全柔顺机构的抽象方法，即应用拓扑学上的连通性原理将柔顺机构抽象成杆件和结点形式，并对相应的数学原理进行了证明；(5)提出了平面全柔顺机构的形状还原和尺寸优化方法，对抽象的柔顺机构进行还原，将其轮廓还原成简单曲线的连接，从而建立尺寸优化模型，对机构进行尺寸优化设计，在得到可加工的机构轮廓的同时又能对关键部位进行特别处理；(6)进行了柔顺机构的数值仿真设计，并将所得设计结果导入商用有限元软件中进行仿真实验，证明了设计方法的可行性和有效性。

Finally, the new approach is extended to synthesis planar six-bar linkages, so that a unified model is established from synthesis of planar four-bar linkages to that of planar six-bar linkages.

本文最后将平面四杆机构综合方法推广到平面六杆机构的综合中去，建立了从四杆到六杆的一致的优化模型。

In this paper, numerical calculations of magnetically induced twist effect in planar nematic liquid crystal are presented. The transmission of polarized light passing through magnetically induced twist distribution in planar nematic liquid crystal is calculated with "4-4" matrix algorithm. On the experimental side, the optical phase retardation method is used to detect the magnetically induced twist effect in planar nematic liquid crystal 5CB(4′-n-penty1-4-cyanobiphenyl) at 27℃.

对平行排列5CB(4′-n-penty1-4-cyanobinpheny1)丝状液晶在静磁场中扭曲变形做了严格的数值解，给出了严格分布情况；利用光学&4*4&矩阵算法，计算了线偏振光在严格分布下的传输情况；在实验方面，应用光学相位延迟法对平行排列5CB丝状液晶在静磁场中(温度27℃)线偏振光的通过情况进行了测量。

To generate planar tiling images with different visual effect by the same iterating mapping, we present a method that allows the P1 planar tessellations to be constructed by a planar dynamic systems with non-equidistant cyclic windows.

为了用同一个迭代映射构造出多个不同视觉效果的平面连续排列图案，提出一种用变周期窗口的动力系统生成具有P1对称特性的平面排列图案的有效算法。

At the same time, the four different genesis types of the sequence interfaces are divided: orogenic erosive sequence unconformity interface, uplift erosive sequence unconformity interface, transgression onlap sequence unconformity interface, exposural sequence unconformity interface; simultaneously the ten concrete mineral showing forms are summarized, i.e. paleo-weathering crust, drossy layer, river rejuvenation surface, paleo-karst surface, slope gravity current erosion surface, intrabasin turbid flow erosion surface, volcanic events surface, lithologic and lithofacies conversion surface, onlap surface and maximium sea flooding surface.

同时归纳出了4种不同的层序界面成因类型：造山侵蚀层序不整合界面、升隆侵蚀层序不整合界面、海侵上超层序不整合界面和暴露层序不整合界面等；同时总结出10种具体的物质表现形式，即：古风化壳、渣状层、河流回春作用面、古喀斯特作用面、斜坡重力流冲刷侵蚀面、盆地内浊流侵蚀面、火山事件作用面、岩性、岩相转换面、上超面和最大海泛面。

The differences between the edge of canopy gap and interior of forest and the differences between trunk surface temperature at the edge and surface temperature in the center of gap were also analyzed. The findings showed that there were high temperature regions on the east and north of middle vertical active surface of edge. So that the vertical active surface of edge is a new thermal active surface on the vicinage of canopy gap beyond soil surface on the interior of forest, soil surface on the gap, and forest canopy surface.

指出在林窗区域，受太阳直接照射的东侧和北侧林墙中部存在表面温度高值区，是林窗区域除林冠面、林窗地面、林内地面之外的新的第4热力作用面，对探讨林窗区域的热量传输、小气候形成以及林窗边缘植物的侧向生长等均有重要意义。

Fostering the concept of multi-culture firmly and mastering the development of advanced culture correctly are conductive to resisting terrorism, separatism of nationalities and ultraism of religion, which is of great academic theoretical, immediate and profound historical si...

牢固树立多元文化的理念和正确把握先进文化的发展方向，有助于在世界范围内自觉地抵制恐怖主义，民族分裂主义和宗教极端主义。不仅具有重大的学术理论意义，而且也具有重大的现实意义和深远的历史意义。

But if anyone walks in the night, he stumbles, because the light is not in him.

11：10 若在黑夜行走，就必碰跌，因为那光不在他里面。