查询词典 measuring error

Error analysis In order to analysis the pose error of the hexapod machine tool, considering the characteristics of the parallel mechanism,"analysis on the error prominency factors for the hexapod machine tool pose error"is proposed. Numerically, the error prominency factor can express the influence on the pose error of the tool resulted from the mechanism parameter error within the whole workspace.

四、位姿误差分析为了定量地对并联机器人机床位姿误差进行分析，结合并联机构的特点，首次提出了&并联机器人机床位姿误差放大因子分析法&，因位姿误差放大因子是反映机床机构参数误差对刀具末端误差影响大小的机床工作空间内的统计值，因此既可作为机床结构参数精度设计的依据又可对机构参数进行优化。

A measuring system which mainly consists of a high precision motorized translation stage of one dimension, POINT GREY Flea2-14S3 CCD camera and LED light source was designed and constructed. Based on a detailed analysis for experiment results, the periodic changing law of system error of LED facula centroid location in this measuring system was found. The results indicate that based on Flea2-14S3 CCD camera, the random error of facula centroid location is about 0.018 pixels, the system error is about 0.06 pixels, and the total error is about 0.063 pixels (1/15 pixels).

利用高精度一维电动平移台、POINT GREY Flea2-14S3 CCD 相机和LED 光源构建了测试系统，对测试结果进行研究和讨论，发现了测试系统LED 光斑质心定位系统误差的周期性变化规律，计算得到了基于Flea2-14S3 CCD 相机的光斑质心定位随机误差为0.018 pixels，系统误差为0.06 pixels，总体误差为0.063 pixels(约1/15 pixels)，能够应用于以光斑质心检测为手段的测量系统中。

The error correction method for microwave measuring line is analyzed, and a new method is proposed which can realize the measurement of error network parameters for microwave measuring line. Then the least square method explicit solutions of error network are given, and the CAT of error network parameters is realized.

分析了微波测量线误差校正的方法，提出了仅用小反射滑动负载即可确定测量线误差网络参数的新方法，给出了测量线误差网络参数的最小二乘法显式解，并实现了测量线误差网络参数的CAT 。

It is pointed out that the error of indication E0 for the calibrated test length which are measured when the offset length between the ram axis and the stylus tip is zero shall neither exceed the maximum permissible error MPEE0 nor exceed 1/3 of the probe error,that the repeatability of E0 shall neither exceed the maximum permissible error MPE Rnor exceed the repeatability error of the probe,and that if the measuring data is rejected in acceptance and reverification,measurement must be carried at least 5 times at the same position for reducing the possibility of misjudgement.

提出探测轴探针针头零偏置长度的校准测试长度的示值误差E0应不超过最大允许校准测试长度的示值误差MPEE0，且不应超过测头误差的1/3；E0的重复性误差R不应超过最大允许重复性误差MPER，且不应超过测头的重复性误差。建议验收校准测量数据超差剔除后，必须在相应位置重复测量5次以上，以减小误判的可能性。

On the basis of the study on the mathematical model of the closed-loop location control, the analysis of contour error in the process motion control and error calculation model, according to the lack of using normal contour error model not to calculate contour error of curve in real-time, combining real-time contour error compensation control strategy and fuzzy logic theory, the fuzzy logic and real-time contour error calculation based self-discipline control strategy is proposed.

2在研究闭环位置控制数学模型、加工轮廓运动控制中的误差分析和轮廓误差计算模型的基础上，针对利用一般运动轮廓误差计算模型不能实时计算出曲线轮廓误差的不足，结合实时轮廓误差补偿控制策略和模糊逻辑理论，研究了基于模糊逻辑理论和实时误差计算的轮廓自律控制策略。

The evaluation method and algorithm of shape error (roundness, plane straightness, space straightness, cylindricity) were discussed. A new kind of algorithm, namely mesh searching method, which can be used to evaluate the roundness error, plane straightness error, space straightness error and cylindricity error, were put forward. With this algorithm, the shape error can be obtained by transferring the distance formula repeatedly and simple judgment without linearzing the distance formula (from point to point or point to line) and choosing optimal direction and step length.

对形状误差(圆度、平面直线度、空间直线度、圆柱度)的评定方法及算法进行了讨论，提出了一种评价圆度误差、平面直线度误差、空间直线度误差及圆柱度误差的新算法——网格搜索法，该算法不需要对距离公式线性化，也不需要选定优化方向和优化步长，只需重复调用距离公式和简单的判断即可得到符合定义的形状误差。

In the paper, a generalized error model for the robots is set up by using DH coordinates. Moreover, a new analytical technique called"analysis on the error prominency factors for the robot pose error"is proposed. Numerically, the error prominency factor can express the extent of influence on the pose error of the end effector resulted form every DH parameter error within the whole working space of the robot.

在这一研究过程中，除了建立了用DH坐标描述的机器人末端位姿误差和轨迹误差的通用模型之外，还提出了一种新的机器人位姿误差分析技术——机器人位姿误差的显著性分析法。

Based on the discussion about fitting normal error's definition, constitution and properties, it was suggested that fitting normal error represented the error of fitting plane linear in old highway. The accuracy index of fitting plane linear in old highway based on fitting normal error was set up. The algorithm of swinging approach on compressible size step that could be used to calculate the fitting normal error was put forward. The method and basic norm of decision about fitting normal error's symbolic were discussed.

在论述拟合法线偏差定义、构成及性质的基础上，提出以拟合法线偏差表征旧路平面线形拟合偏差；建立了基于法线偏差的旧路平面线形拟合精度指标；提出了采用步长压缩摆动趋近法计算拟合法线偏差的算法，并就拟合法线偏差的符号判定准则及方法进行了讨论。

Products for the caliper, micrometer, dial indicator, dial gauge, lever scale thickness measurement tools, etc., as well as precision projector, instrument measuring microscopes, video measuring instrument, the second element altimeter, three-coordinate measuring instrument of precision measuring instruments, etc. mainly used for scientific research units, teaching the field, aerospace, automobile, shipbuilding, electronics, metal, plastic and many other fields in nanotechnology today, represented by technological innovation, it is necessary to adapt to the ever-changing industry needs, constantly drawing and the use of advanced science and technology, high-precision measuring instruments for scientific research in manufacturing has played a role as a bridge has been all over the world the user's trust and support.

产品为卡尺、千分尺、百分表、千分表、杠杆表、厚薄表等测量工具以及精密投影仪、工具测量显微镜、影像量测仪、二次元高度仪、三坐标测量仪等系统精密测量仪器，主要用于科研单位、教学领域、航空航天、汽车、造船、电子、五金、塑料等许多领域，在今天以纳米技术为代表的技术革新，要适应千变万化的产业界的需求，不断的吸取和运用先进的科学技术，高精密测量仪器在为科研制造等方面起到了桥梁作用，得到了全世界各用户的信赖和支持。

The invention belongs to the fluid measuring technical field and relates to an oil, gas and water three-phase oil well continuous gauging device, which comprises a high-efficient gas-liquid separator; the high-efficient gas-liquid separator is connected with an oil, gas and water three-phase inflowing port; a gas phase outlet of the oil, gas and water three-phase inflowing port is connected with a gas phase measuring pipeline; a gas path temperature sensor, a gas path pressure sensor and a gas path endocone flowmeter with high-frequency differential pressure transmitter are arranged on the gas phase measuring pipeline; a liquid phase outlet of the high-efficient gas-liquid separator is connected with a liquid phase measuring pipeline; a liquid path Coriolis mass flowmeter and a liquid path endocone flowmeter are arranged on the liquid phase measuring pipeline; and the cross section of the pipeline for mounting the liquid path Coriolis mass flowmeter is more than the cross section of the pipeline for mounting the liquid path endocone flowmeter.

本发明属于流体测量技术领域，涉及一种油、气、水三相油井连续计量装置，包括高效气液分离器，高效气液分离器与油、气、水三相流入口相连，其气相出口与气相测量管路相连，在气相测量管路上装有气路温度传感器、气路压力传感器、带有高频差压变送器的气路内锥流量计；高效气液分离器的液相出口与液相测量管路相连，在液相测量管路上装有液路科氏质量流量计和液路内锥流量计，安装液路科氏质量流量计的管路的截面积大于安装液路内锥流量计的管路的截面积。

I am a stripper at heart really.

我真的是个心灵的清洁工。

Some,like Leviton's Decora Occupancy Sensor($70),are designed to replace astandard wall switch.Others are ceiling-mounted.

有些人，如立维腾的装扮感应器(70美元)，旨在取代标准的墙壁开关。