查询词典 maximum error

Based on X-filtered LMS algorithm and -filtered LMS algorithm adaptive inverse control, we use a new variable step size LMS algorithm. Adding little computation, variable step size LMS algorithm can result in fast convergence speed and low residual error simultaneously. The adaptive feedback control can counteract the beginning error of the system. The adaptive disturbance canceler can best erase noises and disturbances.

在原来的X-滤波LMS算法自适应逆控制和-滤波LMS算法自适应逆控制方法的基础上，引入了新的变步长LMS算法，在计算量增加不多的前提下，能同时获得较快的收敛速度和较小的稳态误差；引入自适应的反馈补偿控制克服了被控系统的直流零频漂移，使控制系统在初开始工作阶段快速收敛；还引入自适应扰动消除器，它能最大限度的消除扰动。

Experiments shows that it can detect the carrier frequency and the low frequency of modulation signal as expected, the resolution of the carrier frequency is 0.3Hz,the detecting error is within ±0.5Hz, and the resolution of the low modulation frequency is 0.07Hz, the detecting error is within ±0.05Hz.

实验结果表明该检测仪能很好地检测出信号的载频和信号的低频调制信息，其中信号载频的分辨率为0.3Hz，误差范围在±0.5Hz 以内，低频信息的分辨率可达0.07Hz，信号的误差在±0.05Hz。

This paper presents a new effective error-control coding-the double catercorner line redundancy code, which overcomes some defects of the several error controlling codes.

针对常用的差错控制编码存在的缺陷，提出了一种新型的差错控制编码－双向斜行列校验码。

In this paper, according to the characteristics of central projection, aerial photographs were analyzed to discuss displacement of images under tilt conditin or caused by ground undulation, based on which the principles of tilt error and projection error were summarized.

根据中心投影的特性，论述了像片在倾斜条件下所引起的像点位移和像片因地面起伏而引起的像点位移，在对其进行分析的基础上总结出倾斜误差和投影误差的规律，从而说明了不能把像片当作地形图使用。

In this paper, according to the characteristics of central projection, aerial photograph s were analyzed to discuss displacement of images under tilt conditin or caused by ground undulation, based on which the principles of tilt error and projection error were summarized.

本文以航空摄影测量像片为分析对象。根据中心投影的特性，论述了像片在倾斜条件下所引起的像点位移和像片因地面起伏而引起的像点位移，在对其进行分析的基础上总结出倾斜误差和投影误差的规律，从而说明了不能把像片当作地形图使用。这是使用航空像片时必须注意的基本问

Results The measurement error of dental cast analysis is less than 0.09 mm,and the error of three-dimentional cephalometry is less than 0.45 mm.

结果 经检测，模型立体分析的误差小于0.09mm，三维头影测量系统精度为0.45 mm，符合临床要求。

Contour Error of linear and circular motion is caused by following error of each axis position servo system.

由于位置伺服系统跟随误差的存在，导致直线和圆弧运动时产生轮廓运动误差。

By means of analyzing the influence of OD surface roundness error on the outer raceway of bearing ring, the processing method of bearing on internal grinder electromagnetic centerless clamper was improved, the influence of roundness error on outer raceway was decreased, meanwhile, the product quality was raised with less waste products.

通过分析轴承环外径表面圆度误差对轴承环外滚道的影响，改进了轴承在内圆磨床电磁无心夹具上的加工方法，降低了轴承环外径定位表面圆度误差对轴承环外滚道的影响，提高产品质量，达到了降低废品损失的目地。

As the research of the error-correction coding theory going deep, the error-correction code has been widely applied.

随着纠错编码理论研究的不断深入，纠错码的实际应用也越来越广泛。

Statistic analysis result shows that the time step is the most important influence factor of simulation precision, and there is relation between simulation error and the setup value of restitution coefficient which the greater the setup value is, the less the simulation error is. Although there is no effect to the total contact time in the course of collision, the value of the time step decides the total contact step, and there is a logarithmic linear correlativity between them.

统计分析结果表明：计算时步是影响模拟精度最重要的因素；模拟误差还同恢复系数的设定值有关，设定值越大，模拟误差就越小；计算时步的大小虽然对碰撞过程的总接触时间影响不大，但是却决定了碰撞过程的总接触时步数，二者之间存在对数线性相关关系

"The operators will suffer a temporary decrease in the number of consumers and short message services as people may not like having to provide their ID cards for a phone number," Xu Junqi, vice-dean with the Policy-Making Institute of the Telecommunications Research Centre under MII, said yesterday.

信息产业部下属的通信决策研究院副主任徐俊其昨天说：&实行手机实名制后，人们可能不太情愿用身份证注册手机号，所以通信运营商会暂时面临用户减少和短信用户减少的问题。&

I don't believe in make-believe!

我不相信这些虚构的故事。