查询词典 load up

In accordance with the needs of solving problems, mold experiments carried out are as follows:(1) Testing flexural normal stress, shearing stress and shearing force stagnant effect of molds of organic glass and load's lateral distribution coefficient of beam's ribs;(2) Testing rigid torsion and distortion effect of molds of organic glass;(3) Testing cap plates' vertical and lateral efficient load working breadth of molds of organic glass;(4) Testing lateral frame's bending moment of molds of organic glass within the range of their working breadth;(5) Experiment on respondency of dynamic force of molds of organic glass.

根据解决问题的需要，所作的模型试验有：⑴测试有机玻璃模型的弯曲正应力、剪应力、剪力滞效应和箱梁梁肋荷载横向分布系数；⑵测试有机玻璃模型的刚性扭转和畸变效应；⑶测试有机玻璃模型顶板纵向、横向荷载有效工作宽度；⑷测试有机玻璃模型载荷在工作宽度范围内的横向框架弯矩；⑸有机玻璃模型的动力响应试验。

The connected load must limit the reverse load current.

连接的负载必须限制负载电流反向。

Based 188F gasoline engine heat load studies, the research unit based on Using AutoCAD software for the design cylinder sleeve, and then use the software PRO-E 3D modeling, and the calculated and experimental analysis to determine the reference cylinder heat transfer across borders, reuse finite element analysis software ANSYS right cylinder mathematical analysis, systematically on the finite element method in 188F cylinder gasoline engine design of the application, in-depth study of the thermal load on the performance and reliability, as relates to structural strength, stiffness, temperature and so on.

本文以188F汽油机热负荷为研究对象，在研究整机的基础上，利用AUTOCAD软件进行汽缸套的设计，然后用PRO-E软件进行三维建模，并通过计算解析和实验参考确定了气缸套各处的传热边界条件，再利用有限元分析软件ANSYS对气缸套进行数学分析，系统地探讨了有限元法在188F汽油机缸套设计中的应用，深入研究了其热负荷对性能和可靠性的影响，内容涉及到结构强度、刚度、温度场等方面。

A deep beam model is developed to simulate load-bearing wall structure which is perpendicular to the edge of excavation, rigorous solution is derived to find the deformation rule of load-bearing wall, Assuming the position of neutral axis at the lower edge of the beam, the restraint effect of foundation and soil can be considered. Damage rule of the wall under the effect of settlement and horizontal extension are discussed.

将垂直于基坑的承重墙结构简化为深梁模型，通过调整深梁中性轴位置来考虑建筑物与地基的共同作用，通过调整E／G的值来考虑砌体材料的各向异性及门门窗开洞情况，用解析法推导了建筑物的变形规律，研究了建筑物在水平拉伸与沉降共同作用下破坏规律。

This thesis analyses and studies the electric powered servo load system deeper based on the load system of one minitype robot bomb undercarriage, and brings forward some effectual control methods.

本论文就是基于某小型无人飞机起落架伺服加载系统的预研项目，对电动伺服加载系统作了较深入的分析和研究，提出了一些有效的控制方法。

Researched results indicated that contact force's modification was very little inner joints of synchronize Mechanism under the state of no-load and heavy load of sizing press, the rolling force that slab deformed created was supported mostly by side Mechanism.

研究结果表明，调宽机在空载和工作两种状态下，同步机构各构件间的运动副内接触力变化不大，侧压机构主要承受了板坯变形产生的轧制力。

Under the same situation as tube-diameter and so on, yield load and limited load increase with the increasing of steel tube ratio. But the steel tube ratios variety has ruleless to maximum displacement of the upper column.

2在钢管外径等其他属性相同的情况下，屈服荷载与极限荷载随含钢率的增大而增大，但含钢率的变化给柱顶最大位移带来的变化不具有规律性。

Under the same situation as steel tube ratio and volumetric percentage of stirrups and so on, yield load and increases with the increasing of reinforced bar-diameter. But the variety of reinforced bar-diameter has ruleless to limited load and ductibility.

4在含钢率、配箍率等其他属性相同的情况下，屈服荷载随着钢筋直径的增大而增大，但钢筋直径的改变对极限荷载和柱的延性的改变不具有规律性。

America shipped load after load of scrap iron to Japan, while Britain considered blockading the Burma Road .

美国一船船的废铁运到日本，英国在考虑封锁中国的军火。

Physical model and research development of scratch test are reviewed in this paper.The physical relationship between critical load Lc measured by scratch test,shear strength and adhesion energy exists.The critical load Lc can be used to characte

文摘：本文总结了划痕试验法的物理模型及研究现状，临界载荷与涂层和基体之间的界面剪切强度和附着功有物理关系，临界载荷能够表征涂层与基体的结合力。

Tom: You are right, he worked hard all the time.

你是对的。他一直都是努力工作。

Take shortcomings,failures,and mockings of others as commonplace and a drive to complete oneself,hold your own opinion over the evalution and disscution divested from others,afterwards sink into the state of eliminate mistakes if any or encourge oneself being not being influenced by the sayinngs of others or having no ideas to do.

把缺点、失败及别人的耻笑等看成是一种常事，当成完善自己的动力，对别人的评价和议论自己心中有主见，做到&有则改之，无则加勉&，不为人言所左右或无所适从。