查询词典 jaw

Now, all that one has to do is rub the stick against the gum twice, once against the upper jaw and then on the lower jaw, from one end to another, to collect oral mucosal transudate fluid, normally secreted in the oral cavity.

现在，这一切只要用一个棒摩擦牙龈两次，第一次贴着上颚，接着贴着下颚，从一边到另一边去收集口腔粘膜渗出液，通常在口腔秘密的分泌。

The valve channel structure models of molded lines of the valve clacks with various jaw openings were analyzed by using FLOTRAN CFD of ANSYS program, the flow coefficients of various valve cores with different jaw openings were derived.

本文用ANSYS程序中的FLOTRANCFD对几种阀芯型线在各开度下构成的阀道结构模型进行分析，得出不同阀芯在各开度下的流量系数。

The mouth of the dog is then diagramed out into the UPPER JAW and the LOWER JAW, each then divided into halves so that the whole mouth has now 4 quadrants.

犬只的口腔内部被图解为上额及下额，每一个部分又对半分，所以整个结构就由四个部分所组成。

An overshot jaw or a level bite is undesirable. An undershot jaw is a disqualifying fault.

上颚突出式咬和或钳状咬和不符合需要，下颚突出式咬和属于失格。

This paper,based on analyzing the characteristics of spring pin clutch, jaw clutch and plats friction clutch, presents a new typs clutch——spring column pin-jaw clutch, discussing the principle of its work, with the designs of its structural dimensions and calculations of its capacity.

本文在分析弹簧插销离合器、牙嵌离合器和摩擦离合器特点的基础上，提出了弹簧柱销牙嵌离合器，并对这种离合器的工作原理、结构尺寸设计及工作能力计算作了详细的阐述。

Product has ball mill, jaw crusher, fine jaw-breaking machine, hammer crusher, roller crusher, flotation machine, classifier, magnetic separator, conveyor, disc granulator, bucket elevator and efficient energy-saving ball mill, mixer, feeder, conveyor, shaker, high-frequency screen, drum sieve, vibrating screen, do the magnetic roller, mixing bucket, efficient enrichment machine, drying machine, brick machine,×ú, briquettes machines, various models of block machine equipment and so on.

产品有球磨机、鄂式破碎机、鄂式细破机、锤式破碎机、辊式破碎机、浮选机、分级机、磁选机、输送机、圆盘造粒机、斗式提升机、高效节能球磨机、搅拌机、给料机、输送机、摇床、高频筛、滚筒筛、振动筛、干磁辊、搅拌桶、高效浓缩机、烘干机、制砖机、免烧砖机、煤球机，各种型号砌块机设备等。

The main products have jaw crusher, double roll crusher, hammer crusher, steel shell fine jaw crusher, PCL vertical shaft-type hammer crusher, hard rock counterattack crusher, belt conveyor, screw conveyor, bucket elevator machine, planetary mixer compulsory, speed reducers, electric rollers and other equipment and various fittings.

主要产品有颚式破碎机、双辊破碎机、锤式破碎机、铸钢壳细碎颚式破碎机、PCL型立轴锤式破碎机、硬岩反击破碎机、皮带输送机、螺旋输送机、斗式提升机、行星式强制混合机、减速机、电动滚筒等设备及各种配件。

Congenital element, because be born before, of pregnant woman hidebound, systemic sex disease, certain and familial genetic element (if the tooth is mixed,the character of jaw bone and size often affect a tooth, cause dental amlposition or jackknife to wait); Acquired element, basically be undesirable habit (consistent side sex is masticatory, buccal breath, make force of parity of tongue, lip, buccal share is destroyed, those who cause jaw growth is not not well-balanced, harmonious) with all sorts of tooth disease.

先天因素，由于出生前，孕妇的营养不良，全身性疾病，某些家族的遗传因素（如牙齿和颌骨的性状和大小常常影响牙位，造成牙齿错位或重叠等）；后天因素，主要是不良习惯（如一侧性咀嚼，口呼吸等，使舌、唇、颊部分均势力量受到破坏，导致面颌发育的不匀称、不协调）和各种牙病。

The selection rules for the angles of jaw clutch, the determination of the sup ply voltage for the magnet, the design of the control circuit to eliminate the so-called "striking jaw top" and the measures to reduce residual magnetism and the switching time are discussed. The code circuit designing method for the speed control of the spindle box in XHK 5140 machining centre is also described.

本文根据牙嵌式电磁离合器的使用情况，对离合器齿形角的选择原则、激磁电压的设计、消除顶齿的控制电路的设计，以及采用电容器放电消除剩磁和缩短断开时间等问题进行了讨论，最后介绍了XHK5140立式加工中心主轴用电磁离合器变速的译码电路的设计方法。

And those are made by our country are used by other countries,this design of the Jaw crusher is besed on the adventages of the older Jaw crusher ,and studied in improved aspects.

本文所设计的鄂式破碎机是在原鄂式破碎机的基础上，保留了原鄂式破碎机的优点，并对其优化方面进行阐述。

But in the course of internationalization, they meet with misunderstanding and puzzlement.

许多企业已经意识到了这一点，但在国际化的进程中，仍存在一些误区与困惑。

Inorder toaccomplish this goal as quickly as possible, we'll beteamingup with anexperienced group of modelers, skinners, and animatorswhosenames willbe announced in the coming weeks.

为了尽快实现这个目标，我们在未来数周内将公布与一些有经验的模型、皮肤、动画制作小组合作。