查询词典 input data

The boxcars can be rearranged at a shunting yard that has an input track, an output track, and K holding tracks between the input tracks and output tracks.

该车厢可以重新排列在一个调车场具有一个输入采样，输出跟踪，和K之间举行的输入和输出轨轨道轨道。

When 1053 nm 20 ns Nd:YLF laser was used as pump in a 3∶1 inverse expansion system are using attenuators to adjust input energy in the rang of 2 to 92 mJ, the rules of transmitted energy and waveform versus input energy are acquired, and compared with the results of focusing pump.

以波长1053nm、脉宽20 ns的Nd：YLF激光器为光源，采用3∶1的缩束系统，通过衰减片调整入射光能量在2mJ—92mJ变化，获得了透射光能量和功率波形随入射能量变化的规律，并与聚焦条件下的结果进行了比较。

This course is designed Lee AT89C51 microcontroller T0 and T1 count function of the timing function to complete 1S input signal waveform within the number of counted, count resulted in the adoption 74LS48 decoder, the last by four static digital tube display , which showed the result is the input signal frequency.

本次的课程设计是利AT89C51单片机T0的计数功能和T1的定时功能来完成1S内对输入的信号波形的个数进行计数，计数的结果通过74LS48译码器，最后由4位静态数码管显示出来，显示的结果就是输入信号的频率。

To prevent the false input of the anode and cathode wires, NETCCA Sine Prince V-Sine2-10K have the Zero Livewire False Input Detect Function.

为了避免电池输入正负线反接，朗科正弦系列V-Sine2-10K机器具备零火线反接侦测功能。

The apparatus (40) further comprises a second mixer (42) with a second mixer input (45), a second local oscillator input (48), and a second mixer output.

该装置(40)进一步包括具有第二混频器输入(45)、第二本地振荡器输入(48)、和第二混频器输出的第二混频器(42)。

The results show that the plasticity zone and dynamically quiescent layer become fine equiaxed recrystallisation under the thermo-mechanical effect, the grains in the heat-affected zone grow up because of the effect of friction heat. When the rotation speed is 2 500 r/min and the welding time is 12 s, good joint is achieved, and the tensile shear strength of the joint reaches 9.24 kN. The tensile shear strength of spot increases with increasing tool rotation speed, with increasing welding time, the strength increases first, while then reduces. The microhardness of plasticity zone is high, but is slightly lower than that of the base metal, the minimum value of microhardness is in the heat affected zone. When the energy input of joint is high, the fracture type of spot is mode Ⅰ, and the tensile shear strength is high; on the contrary, when the energy input of joint is less the fracture type of spot is mode Ⅱ, and the strength is low.

结果表明：塑性区和动态静止层的晶粒在热和力作用下发生动态再结晶形成细小的等轴晶，热影响区的晶粒在摩擦热作用下长大变粗；搅拌头旋转速度为2 500 r/min，焊接时间为12 s时，可以获得力学性能较好的焊点，焊点的剪切强度达到9.24 kN；焊点的剪切强度随搅拌头旋转速度的增大而增大，随焊接时间的延长先增大后减小；塑性区的显微硬度较高，但略小于母材，接头显微硬度的最小值分布在热影响区；焊点热输入量较多时，接头为Ⅰ型断裂，焊点的剪切强度较高；焊点热输入量较少时，接头为Ⅱ型断裂，焊点的强度较低。

According to password which establishes, uses two pressed keys realizations password the input function, after the password input is correct, locks opens, if inputs three passwords are not correct, locking presses a key 3 seconds, simultaneously discovered reports to the police the sound, after has not pressed a key presses down 3 kinds, only then opens the pressed key locking function; Otherwise still had the pressed key in 3 seconds to press down, relocked presses a key 3 seconds time and reports to the police

根据设定好的密码，采用二个按键实现密码的输入功能，当密码输入正确之后，锁就打开，如果输入的三次的密码不正确，就锁定按键3秒钟，同时发现报警声，直到没有按键按下3种后，才打开按键锁定功能；否则在3秒钟内仍有按键按下，就重新锁定按键3秒时间并报警

Ment must be in zero input or input shortcircuit or an adjustment signal.

注意：调节SPAN比率值和量程设定后，必须检查零点看是否需要重新调整，调零时必须在零输入或者输入一个所需调零值，如4~20mA输入

Notes:Afterthe adjustment of span value and scale setting,you need to check whether zero nment must be in zero input or input shortcircuit or an adjustment signal.Fox example,inputting4~20mA,if you want to display

注意：调节SPAN比率值和量程设定后，必须检查零点看是否需要重新调整，调零时必须在零输入或者输入一个所需调零值，如4~20mA输入

Ment must be in zero input input shortcircuit an adjustment signal.

注意：调节SPAN比率值和量程设定后，必须检查零点看是否需要重新调整，调零时必须在零输入或者输入一个所需调零值，如4~20mA输入

Don not attempt to do something which you can not to do.

不要企图做那些办不到的事情。

The expression of CTGF and TNF-αweredetected by immunochemistry and the number of Clara Cells was calculated.

光镜下观察肺组织的病理变化，采用免疫组化染色观察肺组织中结缔组织生长因子和肿瘤坏死因子-α的表达和Clara细胞的数量。