查询词典 hemispherical shape

Under financial support by the Guanzhong Irrigation Improvement Project loaned by WB,the choice for the shapes of the water measuring flumes in U-shape canals have been carried out,based on the choice research,the straight wall type water measuring flume in U-shape canal was proposed for the optimal shape.

对U形渠道量水槽进行了选型，在选型的基础上，提出以U形渠道直壁式量水槽作为本研究的优选体型，并对U形渠道直壁式量水槽的体型、喉道长度、喉道宽度、过渡段长度、水尺位置、设计方法进行了优化研究，所得结果已在工程实践中应用，取得了良好的经济效益和社会效益。

A new method was developed for design of the composite material flywheel with high speed. In this paper ,the method of optimization of shape design for the composite material flywheel with high speed was put forward on the base of the analytical method and research optimization of shape design, and established the models of density optimization of energy and light mass.These models were used to design two typical composite flywheels with high speed in hybrid electrical vehicle flywheel battery and the stress level and convergence on the flywheel were got .Then a new way was developed for optimization of shape design of the composite material flywheel with high speed.

在此基础上对高速复合材料飞轮进行了形状优化设计，将复合材料有限元分析方法和优化设计技术相结合，提出了复合材料的形状优化的方法，分别建立了以高速复合材料飞轮的以储能密度最大为目标函数的形状优化模型和以质量最轻为设计目标的形状优化模型，并以混合动力客车飞轮电池中高速复合材料飞轮作为具体应用，使其在满足强度条件和几何约束条件下，分别寻求其最大储能密度和最轻质量，从而为高速复合材料飞轮的形状优化设计提供参考依据。

According to the wire electrode on the trajectory of the different forms of control, WEDM can be divided into three types:* is a copy-control, cutting their lines in advance to create the shape of the workpiece and the same mode *, When the rough machining parts and die at the same time * Clamping in the machine tool table, in the process of cutting wire electrode tightly * close to the edge of model for mobile track, thus cutting out the model * with the same shape and precision to work; another One is the optical tracking control, the cutting in line before the first parts in accordance with drawings by a certain ratio of enlarge depicts an electro-optical tracking maps, drawings will be processed when the machine electro-optical tracking placed on the stage, followed on the stage The first photo has to follow the ink line graphics track movement, and then through the use of electrical, mechanical linkage to control the machine tool table work together with the relative electrode wire Xiang Sixing do sports in order to cut out the pattern and shape of the workpiece to the same; a re - Is a digital process control, advanced digital automatic control technology, machine-driven process in accordance with the geometry of the workpiece before the parameters of good pre-processing CNC automatic completion of the processing, production do not look like without drawing board also plans to enlarge, in front of more than two Control in the form of higher precision processing and broad scope of application, at home and abroad for more than 95% of WEDM have been using digital technology.

根据对电极丝运动轨迹的控制形式不同，电火花线切割机床又可分为三种：一种是*模仿形控制，其在进行线切割加工前，预先制造出与工件形状相同的*模，加工时把工件毛坯和*模同时装夹在机床工作台上，在切割过程中电极丝紧紧地贴着*模边缘作轨迹移动，从而切割出与*模形状和精度相同的工件来；另一种是光电跟踪控制，其在进行线切割加工前，先根据零件图样按一定放大比例描绘出一张光电跟踪图，加工时将图样置于机床的光电跟踪台上，跟踪台上的光电头始终追随墨线图形的轨迹运动，再借助于电气、机械的联动，控制机床工作台连同工件相对电极丝做相似形的运动，从而切割出与图样形状相同的工件来；再一种是数字程序控制，采用先进的数字化自动控制技术，驱动机床按照加工前根据工件几何形状参数预先编制好的数控加工程序自动完成加工，不需要制作模样板也无需绘制放大图，比前面两种控制形式具有更高的加工精度和广阔的应用范围，目前国内外95％以上的电火花线切割机床都已采用数控化。

In the jig design process, mainly locates by V shape block and the support plate, depends on the straight clamp and the spring clamps, drills turns diameter two to be supposed to use long trades quickly drills the wrap, when drills turns the diameter incline hole uses the plane incline the jig body, when drills turns the diameter incline hole uses is the horizontal-type drilling machine, when face milling 2 V shape blocks and the milling cutter cannot interfere ,therefore V shape block altitude must reduce, the jig design must be convenient, be simple.

在夹具的设计过程中，主要以V形块和支承板来定位，靠直压板和弹簧来夹紧，钻拐径两孔应采用长型快换钻套，在钻拐径倾斜的孔时采用平面倾斜的夹具体，在钻拐径倾斜的孔时使用的是卧式钻床，铣面时2个V形块与铣刀不能干涉，因此V形块高度要降低，夹具设计要方便、简单。

The different points of views, transverse section, plane and volume changes are considered. The results show that the evolution of the Xinqiao Channel has experienced three stages: in 1861~1926 ,the Xinqiao Channel area had been eroded at first and then silted; the Xinqiao Channel is formed during 1926~1958 with the channel experiencing persistence erosion; from 1958 to 2002, the total volume of the Xinqiao Channel keeps stable with the volume of 5.02×108m^3. The pattern of 10m contour has shaped to a certainty in 1926 and 5m contour of the upper and lower parts of Biandansha has been joined. The change of sections of the Xinqiao Channel reflects its thalweg movement to the North Bank 1.1~2.8 km, its shape changes from "U" shape to "V" shape and its depth has been deepened.

计算结果显示在所研究的区域内自1861年以来新桥水道冲淤过程明显被分为三个阶段：1861~1926年的66a间新桥水道区域经过一段时间的冲刷后又重新产生淤积，总容积变化不大；1926~1958年的33a间新桥水道在不断的冲刷中总容积由2.603亿立方公尺增长到5.076亿立方公尺；1958年至今的45a时间里水道容积基本保持在平均5.02亿立方公尺。1926年新桥水道10m等深线已经形成一定的格局，1947年5m等深线向上延伸，扁担沙已经不再与崇明岛相连；1958年上下扁担沙的5m等深线基本连成一体，可以认为此时新桥水道已经形成。

The shape memory effect of poly{2,5-bis[(4-butoxyphenyl)oxycarbonyl]-styrenes} fiber was studied by TA-Q800 Dynamic Mechanical Analysis. According to the research results, the outstanding shape recovery ability of PBPCS fiber was found. The recovery rate was fastest above 145℃. It cost about 9 minutes recovering from 400% strain to origin length. The repeatability of shape memory was good in 5 repeated times.

本文采用TA-Q800动态热机械分析仪研究了聚乙烯基对苯二甲酸二酯纤维的形变回复性能，发现PBPCS纤维具有非常好的形状记忆效应，在145℃及以上温度，形状回复速率最好，9min左右可以从400％的伸长回复到原来的尺寸，于145℃，重复实验5次，结果说明形变回复重复性好。

In the meanwhile, the TS characteristics of a scattering particle and their relationship are studied when it is passing through the scattering area, In addition to this, the distribution function of particles' shape is defenited in terms of math's method and a new method is putout of which the distribution of particles' shape is captured in according to the power spectrum and spectral distribution characterist of light scattering and finally, the utility of the perturbation ameliorating method and the effect of the particles' shape is modified, so far, the accuracy of measurement of the particles' size is improved effectively.

对此，本文在以Mie散射理论为原理，依据前向接收器接收的前向散射光信息以获取微粒大小信息的测量基础上，对微粒穿越光敏区时的时域与空域的特征以及相关性开展了研究，从数学上定义了微粒的形体分布函数，提出了一种依据光散射功率潜和频谱分布特征来获取微粒形体分布信息的方法，完善了微扰修正理论的应用性，有效地改善了形体的影响问题，从而可提高微粒粒度分布测量结果的准确性。

Wire electrode based on the trajectory of the different forms of control, WEDM can be divided into three types: one is shaped by the imitation controlled cutting in line in advance and work to create the same shape by mold, when processing the workpiece at the same time rough and on the mold clamping in the machine tool table, in the process of cutting wire electrode tightly against the mold on the edge of the track for the mobile, thus cutting out and die on the same shape and precision to the workpiece; another One is the electro-optical tracking control, to carry out the cutting line, before the basis of certain parts to enlarge the proportion of drawings depicts an electro-optical tracking map-processing machines will be placed in design stage of electro-optical tracking, tracking platform Photoelectric first line of graphics has always been to follow the track of the Mexican campaign, and then through the use of electrical, mechanical linkage to control the machine tool table, together with the workpiece so相似形wire electrode relative movement, thus cutting out the same shape and design to the workpiece; again a digital control, the use of advanced automatic control of digital technology-driven machine tool in accordance with the pre-processing parameters according to the workpiece geometry pre-processing procedures for the preparation of a good CNC auto-complete processing, the production does not require appearance on board the need to map to enlarge map of the previous two form of control has a higher machining accuracy and a broad range of applications, both at home and abroad more than 95% have adopted WEDM NC.

根据对电极丝运动轨迹的控制形式不同，电火花线切割机床又可分为三种：一种是靠模仿形控制，其在进行线切割加工前，预先制造出与工件形状相同的靠模，加工时把工件毛坯和靠模同时装夹在机床工作台上，在切割过程中电极丝紧紧地贴着靠模边缘作轨迹移动，从而切割出与靠模形状和精度相同的工件来；另一种是光电跟踪控制，其在进行线切割加工前，先根据零件图样按一定放大比例描绘出一张光电跟踪图，加工时将图样置于机床的光电跟踪台上，跟踪台上的光电头始终追随墨线图形的轨迹运动，再借助于电气、机械的联动，控制机床工作台连同工件相对电极丝做相似形的运动，从而切割出与图样形状相同的工件来；再一种是数字程序控制，采用先进的数字化自动控制技术，驱动机床按照加工前根据工件几何形状参数预先编制好的数控加工程序自动完成加工，不需要制作靠模样板也无需绘制放大图，比前面两种控制形式具有更高的加工精度和广阔的应用范围，目前国内外95%以上的电火花线切割机床都已采用数控化。切割属电加工范畴，是由前苏联人发明的，我国是第一个用于工业生产的国家，当时由复但大学和苏州长风机械厂合作生产的这是最早的机型叫复旦型，我们国内在此基础上发展了快走丝系统。欧美和日本发展了慢走系统LS

In this study, novel nanostructures of metal copper are discovered, including dendritic shape, wire shape and ribbon shape. Those were fabricated using galvanic displacement reaction on aluminum grid. We found that cetyltrimethylammonium chloride played an important role to affect the morphology of the products.

本论文的研究乃在於利用简易的贾凡尼置换反应，於溶液中添加十六烷基三甲基氯化铵(cetyltrimethylammonium chloride； CTAC)与HNO3以合成树状、线状与缎带状奈米铜。

We mainly refered to the one of those improved algorithms of Gerchberg-Saxton.With the computer simulation and drawing program, the simulated diffraction patterns were gotten in this paper, the results agreed with the anticipated diffraction patterns; in the paper we also design the computer optical elements that can shape the laser beam into a double circle shape,a lamp shape and so on.

同时，本文还用标量理论设计了把高斯光束整形为双圆斑形光束的计算机光学元件，文中主要是参考改进的GS(Gerchberg-Saxton)算法；通过计算机模拟，得到了计算机光学元件表面的相位浮雕图。

Tom: You are right, he worked hard all the time.

你是对的。他一直都是努力工作。

Take shortcomings,failures,and mockings of others as commonplace and a drive to complete oneself,hold your own opinion over the evalution and disscution divested from others,afterwards sink into the state of eliminate mistakes if any or encourge oneself being not being influenced by the sayinngs of others or having no ideas to do.

把缺点、失败及别人的耻笑等看成是一种常事，当成完善自己的动力，对别人的评价和议论自己心中有主见，做到&有则改之，无则加勉&，不为人言所左右或无所适从。