查询词典 frictional

The results show that the microstructure of ventra1 scale for python was composed of micro-convex and plank structure that was periodically arranged, it was mensurable and could be described by 9 characteristic parameters. Its surface was different in their forward and backward lean angle. The frictional coefficient of the ventra1 scale had closely relationship with moving direction, it decreased with the increasing load. The value of the frictional coefficient was about 0.07. The frictional coefficient while python moved backward and laterally were equal, and that was 33% more than that moved ahead. The frictional force of the ventra1 scale surface was caused by mechanical tooth function of micro-convex, acting intermolecular force and material's elastic hysteresis. The difference of forward and behind bevel for micro-convex was the anisotropy reason of frictional force.

结果表明：腹鳞表面的微观结构由指状微突体和板结构部分周期排列而成，其结构可用9个特征参数定量描述；腹鳞表面摩擦力由分子作用力、表面微突体的犁沟力、楔形作用力以及材料弹性滞后共同引起；腹鳞表面的摩擦系数在0.07左右并与运动方向有关，摩擦系数随载荷增加而减小；后向运动及左、右侧向运动时摩擦系数基本相等，比前向运动时高33%左右；腹鳞表面微突体不同方向上倾斜角度的差异是引起摩擦各向异性的主要原因。

Single factor experiments were done with the factors including the width of protrusion and the trolley's velocity, which showed that the surface frictional coefficient decreases with the width of protrusion increasing, and doesn't change with the trolley's velocity changing, which was consistent with the results of the orthogonal experiment. A theoretical model of the horizontal projection of a corrugated bionic surface's contact area was built, which showed that the contact area's horizontal projection decreases with width and interval increasing respectively and that the ratio of the contact area's horizontal projection and the vertical load decreases with the vertical load increasing. It indicated that the surface frictional coefficient decreases with the above three factors increasing respectively. Finite element modeling and analysis of interactions of a plate and soils was done using ANSYS, which showed that the plate frictional coefficient is little relative to soil elastic modulus and decreases with vertical surface pressure and that trolley's pull and vertical displacement of bionic surface's control pilot keep constant almost during the plate being pulled. Finite element modeling and analysis of interactions of a corrugated bionic surface and soils was done using ANSYS, which showed that surface frictional coefficient is little relative to soil elastic modulus and decreases with bionic surface's structural parameters and vertical pressure increasing. However, the three factors all didn't affect the surface frictional coefficient remarkably on the condition of 90% dependability. For the first time, bionic surfaces were applied to screw piles, which formed bionic screw piles, and the contrast experiments showed the bionic screw pile had certain resistance-decreasing effects.

建立了波纹型仿生曲面与土壤的接触面积的水平投影的理论模型，表明接触面积的水平投影A随着波纹型仿生曲面突起宽度、两相邻突起间距的增大而减小，接触面积的水平投影与波纹型仿生曲面表面垂直载荷之比随着波纹型仿生曲面表面垂直载荷的增大而减小，进而得出仿生曲面摩擦系数随着波纹型仿生曲面突起宽度、两相邻突起间距以及表面垂直载荷的增大而减小；利用ANSYS软件对平板与土壤的相互作用进行了有限元建模与分析，表明平板摩擦系数与土壤弹性模量关系不大，而随着表面垂直载荷的增大而减小；平板牵引过程中台车牵引力和仿生曲面控制节点垂直方向位移基本保持不变；利用ANSYS软件对波纹型仿生曲面与土壤的相互作用进行了有限元建模与分析，表明波纹型仿生曲面系数在一定范围内基本不受土壤弹性模量的影响，随着波纹型仿生曲面突起宽度、两相邻突起间距以及表面垂直载荷的增大而减小，但在可信度为90％的前提下，三个因素影响都不显著；首次将波纹型仿生曲面应用于与土壤作用方式以挤压为主的螺旋桩，形成仿生螺旋桩，并与普通螺旋桩进行了沉桩对比试验，表明波纹型仿生曲面应用于螺旋桩桩体表面具有明显的降阻作用。

In the paper, the simulation model of port plate/cylinder block frictional pair in which the lubricating film forms was established according to force balance equation and flow continuity equation with SIMULINK of MATLAB. The frictional pair includes of damp groove type continuous oil supply port plate /cylinder block frictional pair and semi-perimeter double oil groove type periodical oil supply port plate /cylinder block frictional pair.

本文根据配流副数学模型中的力平衡动态方程和流量连续方程，利用数学仿真软件MATLAB中的SIMULINK工具包分别对阻尼槽型连续供油配流副和半周槽双油腔间歇供油配流副建立了润滑膜形成的仿真模型，并对不同工况下的这两种配流副润滑膜的形成及变化规律进行动态仿真研究。

In this paper, the frictional characteristics and thermal performance are analyzed for the frictional transmission of cylindrical and conical surface, and the breakage cause of frictional materials is analyzed by tribology and heat transfer principle.

本文对圆柱面和圆锥面的摩擦特性及热性能进行分析，利用摩擦学原理及传热学理论，分析了摩擦材料的损坏原因，并提出了合理解决对策以及两种摩擦副的特点。

The piezoelectric motor includes a piezoelectric member which generates a first vibration mode and a second vibration mode simultaneously by an applied power and a frictional member of which a portion is insertedly attached into a concave portion indentedly formed on one side of the piezoelectric member, wherein the frictional member is in an elliptic motion by the vibration generated by the piezoelectric member, so that an influence of the attachment of the frictional member to a resonance frequency can be minimized.

该压电电机包括：压电构件，通过施加的功率同时产生第一振动模式和第二振动模式；摩擦构件，摩擦构件的一部分插入地附着到凹入地形成在压电构件的一侧上的凹入部分中，其中，摩擦构件通过由压电构件产生的振动进行椭圆运动，从而能够使附着摩擦构件对谐振频率的影响最小化。

Low speed principle of closed - loop system , it can be concluded that the existence of the difference between static frictional and dynamic frictional torque , and the periodic saltation of the dynamic frictional torque , are the main reasons of the low speed stick - skip to the electrohydraulic position servo system

针对伺服马达的低速性能，进行了低速实验研究，并兼顾快速性能进行了阶跃响应和正弦响应实验研究，对实验结果进行了分析，得出了一些有价值的结论，提出下一阶段进行实验的建议。

AlTiN coating has inconspicuous anti-wear effect on carbide.(3) With the introduce of graphite chips bwteen the frictional surface, the effect of graphite chip on the sliding friction and wear behavior of frictional pair was studied. The results show that graphite chips can reduce the coefficient of friction and frictional temperature, and make the coefficient of friction decrease with the decrease of normal load and rise of sliding speed.

在硬质合金微铣刀高速铣削石墨的刀具磨损和破损研究方面，分析了石墨高速铣削过程中的摩擦学条件，揭示了涂层和非涂层硬质合金微铣刀高速铣削石墨的刀具磨损和破损形态及其机理，研究结果表明涂层早期剥落是涂层的早期破损形式，&抛光&磨粒磨损是涂层硬质合金微铣刀在稳定磨损期的主要磨损机理。

In order to do research on pipe flow and pump characteristics of polymer flooding and water flooding rod-pumped well in especially high water-cut stage, rheometric test aimed at production stream from polymer flooding and water flooding rod-pumped well in especially high water-cut stage has been made, and the characteristic of production stream in especially high water-cut stage is confirmed as Newtonian fluid. Experiments using different mediums about pipe flow and pump characteristics is made. Frictional resistance and coefficient of friction resistance of annulus fluid between sucker rod and the pipe flow is calculated under different working conditions. Frictional resistance between plunger and pump barrel under different parameters is calculated based on related theory of pump characteristic and the strained analytical model of oil-well pump. Besides, using the theory of slit flow and hydraulic -clamping pressure, the frictional resistance is calculated, and the error between the result and measured value is no more than 13%.

为研究特高含水期水驱及聚驱抽油机井管流特性与泵特性，本文针对特高含水期水驱及聚驱井采出液进行了流变性试验，确定了特高含水期油井采出液的性质属牛顿流体；利用不同介质，进行管流特性与泵特性试验，得到了不同工况下杆、管环空流的摩擦阻力和摩阻系数；根据泵特性相关理论和抽油泵受力分析模型，计算了不同参数下柱塞与泵筒间的摩擦阻力，并利用缝隙流与液压卡紧力理论对柱塞与泵筒间的摩擦阻力进行了计算，计算结果与实测值误差在13%以内。

The experimental results showed that the frictional factor periodically fluctuated with the time variable, and its amplitude was obviously affected by the change of Reynolds number and pipe diameters. The amplitude and average value of frictional factor both decreased with the increase of Re number, but the bigger the tube diameter was, the larger the amplitude of frictional factor was.

经实验研究发现，试验段内的摩擦阻力系数随时间变化有明显的周期性，雷诺数增加导致摩擦阻力系数的波动幅值降低、平均值减小，管径越粗使得摩擦阻力系数边的波动幅度越大。

The alpaca fiber has good felt ability because of its large frictional coefficient and frictional effect.

纤维的摩擦因数、摩擦效应都比较大，具有很好的缩绒性能。

In the chapter 2, the theoretic knowledge about the photosensitive resin and the grinding tools was firstly introduced.

第二章阐述了光固化树脂结合剂磨具的相关理论研究。

Do not use the program's indenting or margin-setting features; these will be added during typesetting.

不要使用缩排，页面边缘设置之类的选项，偶看不大懂。