查询词典 flutter valve

Pilot-operated pressure reducing valve is to use well in advance to adjust the air pressure instead of springs for voltage regulator, and its regulation principles and the main valve part of the structure and the same direct-acting pressure reducing valve.

先导式减压阀是使用预先调整好压力的空气来代替调压弹簧进行调压的，其调节原理和主阀部分的结构与直动式减压阀的相同。

A refinement of this small-scale direct-acting pressure reducing valve is integrated with the main valve, claimed it as the internal pilot type valve.

若将这个小型直动式减压阀与主阀合成一体，则称其为内部先导式减压阀。

After extended operation, if leakage should occur at the top bearing or across the valve disk of either the Model-B or Model-C valve, this is an indication of wear to the elastomeric seat and/or O-ring seals, requiring their replacement. In most cases, valve replacement will be found less expensive than parts replacement.

在进行操作后，如果泄露出现在型号B或型号C阀门的顶部轴承或阀门阀瓣上，则表明弹性材料阀座和/或O形环密封出现磨损，这时就需要进行更换。

The Metal seated butterfly valve adopts a double eccentric structure and a inclined cone seal. The seal-ring can be separated once open the disk, and the valve can be sealed once the seal-ring contacts the disk. This structure can decrease the friction torque when the butterfly valve opens and closes, and expanded the life time, and make opening and closing easily.

斜锥面金属密封蝶阀设计采用了一个双偏心和一个特殊斜锥椭圆密封结构，实现蝶板在开启瞬间密封面即分离，关闭接触即密封的效果，这种密封结构实现启闭无机械滑动摩擦，大大延长了密封件的使用寿命，并且达到启闭轻松自如目的，且具有密封自动补偿功能。

Working pressure breathing valve did not reach previous: nominal diameter ≤ 150mm, the leakage ≤ 0.04m3 / h; nominal diameter ≥ 220mm, the leakage ≤ 0.4m3 / h; when the breathing valve to the pressure after the work: once the valve disk open, to ensure the normal tank ventilation requirements.

呼吸阀没达到工作压力以前：公称通径≤150mm，其泄漏量≤0.04m3/h；公称通径≥220mm，其泄漏量≤0.4m3/h；当呼吸阀达到了工作压力以后：阀盘立即开启，保证储罐正常的通气要求。

Municipal drinking water enters from the first level check valve, passes through drainage device, second level check valve, to supply water to the water downstream, part of medium enter the lower cavity of diaphragm of drainage device, to close the valve flap of drainage device.

市政饮用水从第一级止回阀进入，经过排污器、二级止回阀，向下游供水，一部分介质由导管进入排污器膜片下腔，使排污器阀瓣关闭。

As solenoid valve the key component in the electronic-control system, the essay focuses on certain solenoid valve construction and characteristics, and set the mathematics model, which used the Simulink to analyze the driving voltage, spring tension and mobile quality, and found that it is complicated on the influence of different factors on solenoid valve, one factor can accelerate the turning off response, but may slower turning on response.

由于电磁阀是电控喷油系统中的关键器件，因此本论文针对某型电磁阀的结构和特点，建立了数学模型。并运用Simulink软件对其进行了仿真研究，分析了驱动电压，回位弹簧预紧力以及运动件质量等对电磁阀响应特性的影响。研究发现影响电磁阀响应特性的因素是十分复杂的，一种因素往往在加速电磁阀关闭响应的同时却会延迟电磁阀开启的响应。

"Hydraulic safety valve" is widely used in hydraulic power systems and hydraulic equipment of safety devices, pressure devices can be limited, is a special valve, which is different from the conventional valve, the traditional use of mechanical valves metal spring as a driving force, can only be limited to low pressure, encountered more BALANCING VALVES than 10Mpa pressure limit pressure can do to increase the volume of pressurized design, the traditional role of the high-pressure valves and high pressure hydraulic power systems and hydraulic equipment The limit pressure of necessity is bulky and complicated structure, difficult to manufacture large, high production costs; in the course of the fatigue of metal spring parameters change fluctuating pressure limiting Ambassador to regular revision to ensure the normal use.

&气动液压安全阀&是目前广泛应用于液压动力系统和液压设备中的安全装置，也可以作限压装置，是一种特殊的阀门，它不同于传统的阀门，传统阀门用机械金属弹簧为动力，只能限中低压力，遇到超过10Mpa以上的压力限压，闸阀只能做加大体积的增压设计，因此传统阀门作用于高压和超高压的液压动力系统和液压设备的限压时必然体积笨重，结构复杂，制造难度大，产品成本高；在使用过程中金属弹簧的疲劳变化大使限压参数波动大，要经常调整才能保证正常使用。

"Hydraulic safety valve" is now widely used in hydraulic power systems and hydraulic equipment in the safety device could also serve as limited pressure device, is a special valve, unlike conventional valves, conventional valves with mechanical metal spring as a driving force, can only be limited to low pressure, the pressure encountered over more than 10Mpa limit pressure can do to increase the volume of the Safety Overflow Valve booster design, the traditional role of the high-pressure valves and high pressure hydraulic power systems and hydraulic equipment The limit pressure of necessity is bulky and complicated structure, difficult to manufacture large, high production costs; in the course of the fatigue of metal spring parameters change fluctuating pressure limiting Ambassador to regular revision to ensure the normal use.

&气动液压安全阀&是目前广泛应用于液压动力系统和液压设备中的安全装置，也可以作限压装置，是一种特殊的阀门，它不同于传统的阀门，传统阀门用机械金属弹簧为动力，只能限中低压力，遇到超过10Mpa以上的压力限压，只能做加大体积的增压设计，因此传统阀门作用于高压和超高压的液压动力系统和液压设备的限压时必然体积笨重，结构复杂，制造难度大，产品成本高；在使用过程中金属弹簧的疲劳变化大使限压参数波动大，要经常调整才能保证正常使用。

Of a tight set of professional production and marketing packages, retirement dumping sets, crushing machine dedicated hub, Park nuts, washers and the only basis for withdrawal of Zhang Tao and manually slurry valve, manually Serous valve, pneumatic valve size, rolling, the rectangle, the first track bolts, T-bolts, knife at the end of bolts, Anchor Bolt, bolt-section,-key, plastic screws, Xiao class, grass-cutting Feidao pinched stainless steel screws and a fan-shaped, needle-shaped nozzle, high strength bolts and nuts, stainless steel bolts and nuts, copper bolts and nuts, motorcycle-wide standard of vehicles, vehicle standard parts, household electrical appliances, electrical equipment standard parts, furniture hardware , Dang Quan, rivets, and various non-standard fasteners GB-pieces, Chong parts, stamping parts, car parts, and so on.

苏州金良机电有限公司系一家专业生产销售紧定套，退卸套、破碎机专用衬套、园螺母、止退垫圈及基础件账套及手动浆料闸阀、手动浆液阀、气动浆液阀、滚动轴承座、长方头道轨螺栓、 T型螺栓、底刀螺栓、地脚螺栓、活节螺栓、平键、塑料螺丝，肖类，切草机飞刀压紧螺钉及不锈钢扇形、针形喷咀，高强度螺栓及螺母、不锈钢螺栓及螺母、铜螺栓及螺母、摩托车全车标准件、汽车标准件、家电、电气设备标准件、家俱五金、挡圈、铆钉、各种GB型紧固件及非标准件、冲制件、冲压件、车制件等。

Panorama Many people are dancing in a large sitting room.

在一个大客厅里，许多人在跳舞。

We fully understand how a microwave oven cooks food, it is first necessary to talk ...

我们充分理解一个微波炉煮的食物，这是首先要谈。。。