查询词典 finite constructibility

The first to use PRO / E software components establishment of the body (body, cylinder head, cylinder pad, cylinder liner, the main bearing caps, Flywheel carcasses, gear Connection Board Room, Shell pump, oil pan, about mounting frame, rear axle oil blocks, etc.) 3D solid model; Then use Hypermesh software division finite element mesh to ensure a good grid quality, and better coordination of the grid between quantity and accuracy of contradictions; Finally using ANSYS software components of a body finite element analysis.

首先利用PRO/E软件建立机体组件（机体、气缸盖、气缸垫、气缸套、主轴承盖、飞轮壳、齿轮室连接板、水泵壳体、油底壳、左右悬置支架、后轴油封盖等）的三维实体模型；然后利用Hypermesh软件划分有限元网格，保证了良好的网格质量，较好地协调了网格数量和计算精度之间的矛盾；最后利用ANSYS软件对机体组件进行了有限元分析。

This paper establishes a finite element model for the interaction between the soil and the sheet piles and performs a seismic response analysis for the portal water injection sheet pile adopting the nonlinear calculation module of finite element software ANSYS.

本文建立的有限元模型之间的互动，土壤和钣桩并进行地震反应分析，为门户注水板桩采用了非线性计算模块的有限元软件ansy

The forming process and the characteristics of plastic deformation, the sites of the heavily strained zones with severe thickness reduction and their evolution, the influences of the main processing parameters, such as the plastic melt pressure and its distribution from the gate to the end of the mold, and of friction coefficient between the sheet flange and the mold, on these during the hybrid forming of the aluminum sheet have been revealed by the updated Lagrange finite element formulation for the finite elastic-plastic deformation.

运用弹塑性大变形更新的Lagrange有限元方法，揭示了铝薄板的成形过程和塑性变形的特点与规律、大塑性变形区的产生位置及其塑性变形特点，探明了复合成型过程中塑料熔体压力及其分布规律以及铝薄板凸缘与模具摩擦系数等主要工艺参数对铝薄板成形过程和塑性变形的影响规律。

In this paper, based on the finite element method, a three-dimensional finite element model was selected to simulate performance of the self-tapping screw connections and the failure modes of the panel, considering material nonlinearity and changing-status nonlinearity.

本文运用有限单元法，建立三维实体有限元模型，考虑了材料非线性与接触非线性，对钢板－自攻螺钉连接的受力情况和破坏模式进行了细致研究。

Single factor experiments were done with the factors including the width of protrusion and the trolley's velocity, which showed that the surface frictional coefficient decreases with the width of protrusion increasing, and doesn't change with the trolley's velocity changing, which was consistent with the results of the orthogonal experiment. A theoretical model of the horizontal projection of a corrugated bionic surface's contact area was built, which showed that the contact area's horizontal projection decreases with width and interval increasing respectively and that the ratio of the contact area's horizontal projection and the vertical load decreases with the vertical load increasing. It indicated that the surface frictional coefficient decreases with the above three factors increasing respectively. Finite element modeling and analysis of interactions of a plate and soils was done using ANSYS, which showed that the plate frictional coefficient is little relative to soil elastic modulus and decreases with vertical surface pressure and that trolley's pull and vertical displacement of bionic surface's control pilot keep constant almost during the plate being pulled. Finite element modeling and analysis of interactions of a corrugated bionic surface and soils was done using ANSYS, which showed that surface frictional coefficient is little relative to soil elastic modulus and decreases with bionic surface's structural parameters and vertical pressure increasing. However, the three factors all didn't affect the surface frictional coefficient remarkably on the condition of 90% dependability. For the first time, bionic surfaces were applied to screw piles, which formed bionic screw piles, and the contrast experiments showed the bionic screw pile had certain resistance-decreasing effects.

建立了波纹型仿生曲面与土壤的接触面积的水平投影的理论模型，表明接触面积的水平投影A随着波纹型仿生曲面突起宽度、两相邻突起间距的增大而减小，接触面积的水平投影与波纹型仿生曲面表面垂直载荷之比随着波纹型仿生曲面表面垂直载荷的增大而减小，进而得出仿生曲面摩擦系数随着波纹型仿生曲面突起宽度、两相邻突起间距以及表面垂直载荷的增大而减小；利用ANSYS软件对平板与土壤的相互作用进行了有限元建模与分析，表明平板摩擦系数与土壤弹性模量关系不大，而随着表面垂直载荷的增大而减小；平板牵引过程中台车牵引力和仿生曲面控制节点垂直方向位移基本保持不变；利用ANSYS软件对波纹型仿生曲面与土壤的相互作用进行了有限元建模与分析，表明波纹型仿生曲面系数在一定范围内基本不受土壤弹性模量的影响，随着波纹型仿生曲面突起宽度、两相邻突起间距以及表面垂直载荷的增大而减小，但在可信度为90％的前提下，三个因素影响都不显著；首次将波纹型仿生曲面应用于与土壤作用方式以挤压为主的螺旋桩，形成仿生螺旋桩，并与普通螺旋桩进行了沉桩对比试验，表明波纹型仿生曲面应用于螺旋桩桩体表面具有明显的降阻作用。

Based on rolling technology of 2050 hot strip roughing mill group, a 3-D coupling thermal, mechanical and microstructural rigid-plastic finite element model had been developed by using nonlinear finite element method and physical metallurgy microstructural evolution models.

根据某厂2050热带钢粗轧机组轧制工艺，借助物理冶金组织演变模型，利用非线性有限元法开发了热连轧过程热、力、组织耦合三维刚塑性有限元模型。

This paper puts forward CS roof plate finite element model and its analyse method. The analysis result indicates that the finite element model and analyse method is appropriate and makes some analyse of the CS plates with different distributed steel.

本文提出了三步节能CS屋面板有限元模型建立以及分析方法，分析结果表明本文建立的有限元模型和采用的分析方法是合理的，并利用有限元方法对其他配筋形式的三步节能CS屋面板进行了分析。

S the rational finite element interpolates with the soultions of elasticity and formulates directly in the physical domain, it has superiority over the isoparametric finite element in clear physical meaning and accuracy.

bstract 由于理性有限元用弹性力学的解插值并且在物理域内直接列式，因而与等参元相比，具有物理意义明确和精度高的优点。

An equal cross-section blade was investigated and a finite element model was built parametrically. Geometrical parameters (such as length, width and thickness), material parameters (such as young's modulus and density) and speed of blade were considered as input random variables while the static frequencies and dynamic frequencies were output random variables. Combining the finite element method, response surface method and Monte Carlo method, the statistical properties and cumulative distribution functions of static frequencies and dynamic frequencies were obtained. Probability sensitivities analysis, which combined the slope of the gradient and the width of the scatter range of the random input variables, was applied to quantitatively evaluate the sensitivities of static frequencies and dynamic frequencies with respect to the random variables. The Scatter plots of structural responses with respect to the random input variables were illustrated how to adjust the values of the static frequencies and dynamic frequencies by changing input random variables.

文中以某试验台用汽轮机等直叶片为研究对象，考虑几何参数、材料参数和转速的随机性，通过有限元参数化建模，将确定性有限元方法、响应面方法和Monte-Carlo模拟法相结合，从而获得了叶片静频、动频的统计特性和累积分布函数；同时考虑随机变量的梯度和离散范围对静、动频的影响，通过概率敏感性分析，定量地判断出叶片静、动频对随机输入变量的敏感性；通过绘制叶片静、动频与输入变量的散点图，定量地分析了如何改变随机变量以调整静、动频率的方法。

In order to verify the accuracy of heat transfer coefficient,2D nonlinear finite element axisymmetric model is established by the means of finite element software MSC.Marc, which is utilized to simulate the transient temperature field coupled with phase transformation process and nonlinear synthetic surface heat transfer coefficient of several typical steels in the different quenchants.

Marc作为模拟平台，建立了淬火过程二维非线性有限元模型，模拟淬火过程中的瞬态温度场，在模拟过程中以多种常用钢在不同淬火介质中的非线性表面综合换热系数为边界条件，同时耦合了相变过程的影响。

He has to relate with three women in the movie, and yet remain implicitly faithful to the unseen Lucinda.

让克劳德布里亚里成功地饰演试验了一个难度很大的角色：和三个女人打交道，但还要底下对观众未曾谋面的卢馨达保持忠诚。

The experiment was conducted to study effects of inulin on the growth performance, indices of immune organs and serum immunoglobulin of laying chicklings as well as the performance of inulin which replaced the antibiotics in diets by adding 0.2%, 0.4% and 0.8% of inulin, respectively.

试验旨在通过在蛋用雏鸡日粮中添加0.2%、0.4%和0.8%的菊粉，研究菊粉对蛋雏鸡生长性能、免疫器官指数和血清免疫球蛋白的影响，以及菊粉替代抗生素对蛋雏鸡的应用效果。