查询词典 filler wall

It is the most ideal filler material of reburner , reacting furnace, filler furnace on oil and chemical industries.

应用领域：是广大石油、化工行业中转化炉、反应炉、填料塔中最为理想的填料。

As an important parameter measuring the inter-function of mine filler/glue stock, the higher is Wa/γSL, the stronger is the inter-function of mine filler/glue stock. Then the composite material will have a better mechanical property.

作为衡量矿物填料/胶料基体相互作用强弱的一个重要参数， Wa/γSL值越大，矿物填料/胶料基体相互作用就越强，所形成的复合材料就具有较好的力学性能。

The ambient-temperature tensile strength of the joint brazed with Cu-Co-Ti filler metal is slightly higher than that brazed with Cu- Ti filler

两种接头的的室温拉伸强度均较低，但Cu-Co-Ti钎料接头的强度高于Cu-Ti钎料接头。

The effects of brazing temperature on spreadability of series Ni-P filler metal and mechanical property of the stainless steel joint brazed with the filler metal were studied.

中文摘要：研究了钎焊温度对Ni-P系钎料铺展性能及其真空钎焊0Cr13不锈钢接头力学性能的影响。

The research indicate that the performance of brazing joint using Al-Ge-Si brazing filler metal precedes to the one using HL401 brazing filler metal. And the main reason is that brittle compound such as Cu2Al is not appeared in brazing joint.

本研究建立的2090Ce铝锂合金钎缝组织形态成长模型以及母材溶解厚度控制模型对钎料的选择、钎焊工艺参数的选择及接头钎焊间隙的确定等具有重要的参考和指导作用。

Compared with the joint brazed with Cu-Ti filler metal, the content of Cu in the reaction layer adjacent to the stainless steel is higher than the joint brazed with Cu-Co-Ti filler metal, so is the content of Nb in brazing seam.

与Cu-Ti钎料接头相比，Cu-Co-Ti钎料接头中钎缝与不锈钢侧的反应层中Cu含量较高，钎缝中Nb含量也较高。

AgCuTi active filler metal exhibits a good wettability to brazing cBN, joint interface between filler metal and cBN is compact, and a reaction layer is formed between them.

AgCuTi 活性钎料对cBN的润湿性较好，界面结合紧密，并在界面处形成反应层。

Ag-Cu-Ti active filler metal exhibits a good wettability to brazing c-BN, joint interface between filler metal and c-BN is compact, and a reaction layer is formed between them.

Ag-Cu-Ti活性钎料对c-BN的润湿性较好，界面结合紧密，并在界面处形成反应层。

The results demonstrate that welds with good appearances could be obtained when welding with the appropriate processing parameters. The as-welded joint tensile strength without filler wire is 180.7 MPa, while the tensile strength is 190 MPa when welding by one side with the filler wire of AlSi12 or AlMg4.5MnZr.

研究结果表明，在合适的工艺参数下，可以获得表面光洁、正反面焊缝成型良好的对接接头；焊态下，单面焊接不填充焊丝的接头强度为180.7 MPa；单面焊接填充AlSi12，AlMg4.5MnZr焊丝的接头强度最低为190 MPa，且两种填充焊丝接头的拉伸强度无明显差异；双面焊接填充AlMg4.5MnZr焊丝的接头强度达到200.7 MPa，约为母材的90%。

Using high frequency induction brazing and TiZrNiCu filler metal, the shear strengths of the joints were low. The maximum shear strengh was only 102.1MPa, which was lower than the maximum strength of vacuum brazing. The reasons may be that excessive intermetallics, holes and oxidation existed in the joint. So TiZrNiCu filler metal isn't fit for non-vacuum brazing.The stress variation, stress distribution and crack-sensitive regions during the cooling process of brazing have been studied by Marc non-linear software.

采用气体保护高频感应加热、TiZrNiCu钎料钎焊时，接头的强度普遍偏低，最高的剪切强度只有102.1MPa，远远低于辐射加热真空钎焊的强度，其原因是接头中局部生成了过量的金属间化合物，且产生氧化，接头中含有较多的气孔等影响了接头强度，因此可以认为TiZrNiCu钎料不适合在非真空条件下的钎焊。

We are forbidden from giving money to these shoeless, skinny children, as this will perpetuate begging.

向光着脚，骨瘦如柴的孩子施舍是不可以的，因为要招来无休无止的乞讨。

It would be hard not to fall victim to some sharpeyed policeman.

要想不被某个目光锐利的警察抓到，谈何容易。